Introduction To Finite Element Analysis And Design
2nd Edition
ISBN: 9781119078722
Author: Kim, Nam H., Sankar, Bhavani V., KUMAR, Ashok V., Author.
Publisher: John Wiley & Sons,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 45E
Repeat problem 44 for the truss on the right side of the figure. The properties of element 6 are same as those of element 5, but
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Calculate the reaction forces at points P and Q as [kN] using the information given in the figure.
PROBLEM 3: A right-angled rigid pipe is fixed to a wall at A and is additionally supported through the cable CD as shown in the figure. The tension in the cable is 3 kN. Neglect the weight of the pipe. Use the Right-Hand-Rule to indicate the direction of the moment.
[8] Calculate total force reaction at A. (ANSWER: 3.00 KN)
[9] Calculate the moment reaction (including correct sign) at A about z-axis. (ANSWER: 2.168 KN-m)
[10] Calculate the moment reaction (including correct sign) at A about x-axis. (ANSWER: -0.843 KN-m)
In the figure below, the trusses are all stable. Compute the magnitude of reaction at C in
kips.
link
truss 1
truss 2
15
40
201
15'
В
link
20'
24 kips
60 kips
A S
- 20' 20-20 20' → 20-
Chapter 1 Solutions
Introduction To Finite Element Analysis And Design
Ch. 1 - Answer the following descriptive questions a....Ch. 1 - Calculate the displacement at node 2 and reaction...Ch. 1 - Repeat problem 2 by changing node numbers; that...Ch. 1 - Three rigid bodies, 2,3, and 4, are connected by...Ch. 1 - Three rigid bodies, 2,3, and 4, are connected by...Ch. 1 - Consider the spring-rigid body system described in...Ch. 1 - Four rigid bodies, 1, 2, 3, and 4, are connected...Ch. 1 - Determine the nodal displacements, element forces,...Ch. 1 - In the structure shown, rigid blocks are connected...Ch. 1 - The spring-mass system shown in the figure is in...
Ch. 1 - A structure is composed of two one-dimensional bar...Ch. 1 - Two rigid masses, 1 and 2, are connected by three...Ch. 1 - Use the finite element method to determine the...Ch. 1 - Consider a tapered bar of circular cross section....Ch. 1 - The stepped bar shown in the figure is subjected...Ch. 1 - Using the direct stiffness matrix method, find the...Ch. 1 - A stepped bar is clamped at one end and subjected...Ch. 1 - A stepped bar is clamped at both ends. A force of ...Ch. 1 - Repeat problem 18 for the stepped bar shown in the...Ch. 1 - The finite element equation for the uniaxial bar...Ch. 1 - The truss structure shown in the figure supports a...Ch. 1 - The properties of the two elements of a plane...Ch. 1 - For a two-dimensional truss structure as shown in...Ch. 1 - The 2D truss shown in the figure is assembled to...Ch. 1 - For a two-dimensional truss structure as shown in...Ch. 1 - The truss shown in the figure supports force Fat...Ch. 1 - Prob. 27ECh. 1 - In the finite element model of a plane truss in...Ch. 1 - Use the finite element method to solve the plane...Ch. 1 - The plane truss shown in the figure has two...Ch. 1 - Two bars are connected as shown in the figure....Ch. 1 - The truss structure shown in the figure supports...Ch. 1 - It is desired to use the finite element method to...Ch. 1 - Determine the member force and axial stress in...Ch. 1 - Determine the normal stress in each member of the...Ch. 1 - The space truss shown has four members. Determine...Ch. 1 - The uniaxial bar shown below can be modeled as a...Ch. 1 - In the structure shown below, the temperature of...Ch. 1 - Prob. 39ECh. 1 - The three-bar truss problem in figure 1.23 is...Ch. 1 - Use the finite element method to determine the...Ch. 1 - Repeat problem 41 for the new configuration with...Ch. 1 - Repeat problem 42 with an external force added to...Ch. 1 - The properties of the members of the truss in the...Ch. 1 - Repeat problem 44 for the truss on the right side...Ch. 1 - The truss shown in the figure supports the force ....Ch. 1 - The finite element method as used to solve the...Ch. 1 - Prob. 48E
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What are some of the applications of adhesives in the automotive industry?
Degarmo's Materials And Processes In Manufacturing
The moment of the force F about an axis extending between A and C.
Engineering Mechanics: Statics & Dynamics (14th Edition)
A person applies an insect repellent onto an exposed area of A=0.5m2 of their body. The massof spray used is M=...
Fundamentals of Heat and Mass Transfer
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
The combined action of the three forces on the base at O may be obtained by establishing their resultant throug...
Engineering Mechanics: Statics
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the ...
Statics and Mechanics of Materials (5th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH=1200N (C) as indicated in Figure 2. Determine the loads P1, P2, and P3 as well. Use four decimal places.arrow_forwardI need help please Two gondolas on a ski lift are locked in the position shown in the figure while repairs are being made elsewhere. The distance between support towers is L = 100 ft. The length of each cable segment under gondola weights WB = 450 lb and WC = 650 lb are DAB = 12 ft, DBC = 70 ft, and DCD = 20 ft. The cable sag at B is ΔB = 3.9 ft and that at C(ΔC) is 7.1 ft. The effective cross-sectional area of the cable is Ae = 0.12 in2.(a) Find the tension force in each cable segment; neglect the mass of the cable.(b) Find the average stress (s) in each cable segment.arrow_forwardRAY F Enter Fpc: Enter Fr The figure above is a pin-joint frame with horizontal member length 1 = 2m and vertical member length h = 4m. (Note that the diagram is not to scale.) You are given that F₁ =45kN, RAY = 15kN and Rpy = 30kN. Use the method of sections to calculate the forces in members BC, FC and FE. Enter your answers in kilonewtons (kN) correct to 2 decimal places. Enter Fac: KN KN F₁ KN RDYarrow_forward
- RAX M A 0 F RAY Enter FAP: kN F₂ The figure above is a pin-joint frame with angle = 30° between members AF and AB. (Note that the diagram is not to scale). Given that the reaction forces at the support A are given by RAX = 10kN and RAY = 25kN, calculate the forces in members AB and AF, denoted by FAB and FAP respectively. Enter your answers in kilonewtons (kN) correct to 2 decimal places in the boxes below: Enter FAB KN D RDYarrow_forwardThe cantilever truss in the figure is hinged at D and E. Find the force in member AC. 1000 1b 60 60° 30 lo00 16 c00 16.arrow_forwardFind the residual forces acting in a truss with members’ AC=1000N (T), EG=520N (T), and FH= 1200N (C) as indicated in Figure 2. Determine the loads P1, P2, and P3 as well.arrow_forward
- Find the residual forces acting in a truss with members’ AC=1000N (T), EG=520N (T), and FH= 1200N (C)as indicated in Figure 2. Determine the loads P1, P2, and P3 as well.arrow_forwardPROBLEM 4: Find the reaction force components at point A and B. The member AB has a length of L=10m. The infinitesimal loads at point A and B are 1200N/m and 800N/m respectively. 12=5mm 1200 N/m/ A In L=10m 4₁=5m 0:38 800 N/marrow_forwardThe elements of a floor jack are shown in the figure. The figure CDFE is a parallelogram. Calculate the magnitude of the force in the hydraulic cylinder AB corresponding to the 2270-Ib load supported as shown. What is the magnitude of the force in link EF? Assume W = 2270 lb, a = 2.90 in., b = 3.10 in., c = 4.45 in., d = 8.75 in., e = 1.95 in., and f = 1.95 in. W e D b. a A E Answers: AB = i Ib EF = i Ibarrow_forward
- A bent pipe is attached to a wall with brackets as shown. A force of F = 170 lb is applied to the end of the tube with direction indicated by the dimensions in the figure. Determine the support reactions at the brackets B, C, and D. Model these brackets as journal bearings (only force reactions perpendicular to the axis of the tube) and neglect couple moment reactions. Assume the distance between the supports at B and C and the tube bends nearby are negligible such that the support at Cis directly above the support at D and the dimension g gives the distance between supports B and C. Enter your answers in Cartesian components. 2013 Michael Swanbom BY NC SA d A FK Values for dimensions on the figure are given in the table below. Note the figure may not be to scale. Variable Value 8.68 in 14.9 in 14.2 in d 46.5 in h 29.5 in 31.0 in The reaction at B is B = k lb. The reaction at C is Ć = k lb. The reaction at D is D ĵ + k lb. +arrow_forwardProblem 4.61 Figure 15m 0.5m B 2.5 m 1 of 1 Part A Determine the magnitude of the moment of the force F = {50i- 21 j-80k} N about the base line AB of the tripod. (Figure 1) Express your answer to three significant figures and include the appropriate units. MAB= Submit μÀ Value Request Answer < Return to Assignment Units Provide Feedback ?arrow_forwardFind the rod forces 1, 2 and 3 of the plane truss system shown in the figure. 4m 3m 60kN 40kN 60kN 3m 3m 3marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Basics - Statics & Forces in Equilibrium; Author: Solid Solutions - Professional Design Solutions;https://www.youtube.com/watch?v=dQBvQ2hJZFg;License: Standard YouTube License, CC-BY