Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 4, Problem 4.49P
Consider a one-dimensional fin of uniform cross-sectionalarea, insulated at its tip,
- Derive the finite-difference equation for any interiornode m.
- Derive the finite-difference equation for a node n located at the insulated tip.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Please solve asap,
Will provide helpful ratings for complete solution. Thank u
A double-glazed window is constructed such that it has 5 mm thick glass as the inside layer, 4 mm layer of gas, and finally 5 mm thick glass as the outer layer. Which have thermal conductivies of 0.7, 2.120, and 5.9 W m-1 K-1, respectively.
Calculate the heat loss per unit area, Wm-2 through the glass if the inside temperature of the glass is 11.09 °C and the outside temperature is 6.47 °C
Report your answer to 2 decimal places.
2. The slab shown is embedded in insulating materials on five
sides, while the front face experiences convection off its face.
Heat is generated inside the material by an exothermic
reaction equal to 1.0 kW/m'. The thermal conductivity of the
slab is 0.2 W/mk.
a. Simplify the heat conduction equation and integrate
the resulting ID steady form of to find the
temperature distribution of the slab, T(x).
b. Present the temperature of the front and back faces of
the slab.
n-20-
10 cm
IT- 25°C)
100 cm
100 cm
1. A simple cavity wall consists of two brick layers separated by an air gap of 50 mm. If the inside air temperature is 20oC and the ambient outside temperature is 5 oC, calculate the heat flux through the wall. Bricks are 100 mm thick with thermal conductivity kbrick = 0.5 W/m K, hin = 10 W/m2 K, hout = 20 W/m2 K. The internal air cavity can be considered still (no convection) with kair = 0.015 W/m K.
2. On a day in winter, the outside air temperature drops to -5 oC and the outside convective heat transfer changes to hout = (2 x V) + 8.9 W/m2 K. If the outside wind speed gusts at 50 kph, calculate the change in heat flux for the wall in question 3.
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6arrow_forward1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4arrow_forward(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = = W 3 m. k . Ay m-1, n m, n | Δx=" m, n+1 m, n-1 The side insulatedarrow_forward
- 6. A furnace wall consists of 250 mm fiber brick,125 mm insulating brick, and 250 mm building brick. The inside wall is at a temperature of 600°C and the atmospheric temperature is 20°C. Calculate the heat loss per m' of wall area and the temperature of the outside wall surface of the furnace and the temperature at each interface throughout the wall. The heat transfer coefficient for the outside surface is 10 W/m² °k and the thermal conductivities of the fiber brick, insulating brick and the building brick are 1.4,0.2 and 0.7 W/m.°C respectively.arrow_forwardA composite wall is made up of an external thickness of brickwork 110 mm thick insidewhich is a layer of fiberglass 75 mm thick. The fiberglass is faced internally by an insulatingboard 25 mm thick. The coefficient of thermal conductivity for the three are as follows: Brickwork 1.5 W/m-KFiberglass 0.04 W/m-KInsulating board 0.06 W/m-KThe surface transfer coefficients of the inside wall is 3.1 W/m2 -K while that of the outside wall is 2.5 W/m2 -K. Take the internal ambient temperature as 10°C and the externaltemperature is 27°C. Determine the heat loss through such wall 6 m high and 10 m long.arrow_forwardA 1-D conduction heat transfer problem with internal energy generation is governed by the following equation: +-= dx2 =0 W where è = 5E5 and k = 32 If you are given the following node diagram with a spacing of Ax = .02m and know that m-K T = 611K and T, = 600K, write the general equation for these internal nodes in finite difference form and determine the temperature at nodes 3 and 4. Insulated Ar , T For the answer window, enter the temperature at node 4 in Kelvin (K). Your Answer: EN SORN Answer units Pri qu) 232 PM 4/27/2022 99+ 66°F Sunny a . 20 ENLARGED oW TEXTURE PRT SCR IOS DEL F8 F10 F12 BACKSPACE num - %3D LOCK HOME PGUP 170arrow_forward
- (a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = W 3 m. k Ay m-1, n 11- m2, 11 m, n+1 m, n-1 The side insulatedarrow_forwardA plane wall of thickness 8cm and thermal conductivity k=5W/mK experiences uniform volumetric heat generation, while convection heat transfer occurs at both of its surfaces (x= -L, x= + L), each of which is exposed to a fluid of temperature T∞ = 20˚C. The origin of the x-coordinate is at the midplane of the wall. Under steady-state conditions, the temperature distribution in the wall is of the form T(˚C) = a + bx - cx^2, where x is in meters, a =86˚C, b = -500˚C/m, and c=4459. 1) Heat Flux Entering the wall is ? 2) Temperature at the left face is /arrow_forward(a) Consider nodal configuration shown below. Derive the finite-difference equations under steady-state conditions for the following situations. (a) The boundary is insulated. (b) The boundary is subjected to a constant heat flux. m, n+1 Ay Im, n The side insulated m-1, n I I Ax- m, n-1arrow_forward
- 1- Fin question {(b) (Accounting the heat transfer at the end)} 2- Derive a nodal equation for analysis of the node(n) in the Figure below 1 n 3- Aluminum plate having a thickness of 4cm and initial temperature is 200 °C. The plate is subjected to a convection with h= 500 w/m².°C and T= 25 °C. Using lumped heat method, calculate the temperature at time of 24.2 sec. Take the density = 2707 kg/m³ , Cp =896 j/kg. °C , k= 204 w/m. °Carrow_forwardPROBLEM 1: The block of 304 stainless steel shown below is well insulated on the front and back surfaces, and the temperature in the block varies linearly in both the x- and y-directions. Find: (a) The heat fluxes and heat flows in the x- and y-directions. (b) The magnitude and direction of the heat flux vector. 15°C 5°C 5 cm y 5 cm- 10 cm The thermal conductivity of 304 stainless steel is 14.4 W/m K. 10°C 0°Carrow_forwardProblem 4 A cork board (k = 0.039W/m K) 3 cm thick is exposed to air with an average temperature T.. = 30°C with a convection heat transfer coefficient, h = 25 W/m².K. The other surface of the board is held at a constant temperature of 15°C. A volumetric heat generation of 5 W/m³ is occurring inside the wall. Assuming one dimensional conduction, write the governing equation and express the boundary conditions for the wall. (solve the equation is not required) Problomarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license