Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.67P
To determine
The heat rate from the each duct per unit length.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A heater coil is completely immersed in an oil bath that is insulated on all sides except for
the top where the oil is in direct contact with the surrounding air that is maintained at a
constant temperature, Oair. At t=0s, the coil is switched on and provides in watts of
electrical power to the oil which has a thermal mass of moil and an initial temperature of
Oinit-oil. The temperature of the oil is denoted by oil and the thermal resistance between
the oil and air is Roil-air-
a) Draw a schematic of the system clearly labeling the (assumed) directions of the
heat transfer rates and the temperature at every node.
b) Derive the governing differential equation for the temperature of the oil, oil-
c) Where does Oinit-oil appear in the system schematic and how does it affect the
governing equations?
d) Derive an expression for the steady-state temperature of the oil as a function of
the various system parameters.
A camera used for monitoring marine life is placed in water where T.. -5°C and the
convection heat transfer coefficient h=1420 W/m²K. The camera is operating, but
its battery is experiencing thermal runaway, causing the camera to become very hot,
and there is volumetric heat generation, qe inside it. There is no heat generation
within the waterproof, protective enclosure surrounding it.
00:08
The camera is already compromised; however, its owner hopes to save the protective
case. Each interface (between layers A and B and between layers B and C) must not
exceed a temperature of 185°C, or these plastic, protective layers will begin to melt.
Approximate the camera and its casing as a composite, rectangular object with flat
surfaces. The device's total thickness, L=LA + 2LB +Lc, is much smaller than its area
(into the page); therefore, 1-D conduction can be approximated through the layers.
On the left surface of layer A, the temperature is measured to be T₁ = 8.0°C, and the
temperature on…
In a new residential project, you strongly believethat double-paned windows are ‘better’ than singlepaned windows. Compare the rate of heat loss betweensingle and double-paned windows (1.5 m x 1 m) if thethickness of each pane is (th = 0.4 cm) and (k = 0.9W/m.K). The indoor and outdoor temperatures are 18°C and 2 °C, respectively. Thickness of the air gapbetween the double-paned windows is (th = 1 cm), and(k = 0.022 W/m.K). Image credit: Windowwhirl
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.arrow_forwardOne vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.Karrow_forwardA composite plane wall consisting of materials, 1.5-in steel (k = 312 BTU-in/HR.ft2.0F) and 2-in aluminum (k = 1400 BTU-in/HR.ft2.0F), separates a hot gas at Ti = 2000F, hi = 2 BTU/HR.ft2.0F, from cold gas at To = 80 deg F, ho = 5. If the hot fluid is on the aluminum side, find: a) Transmittance, U; b) The heat through 100 sq. ft of the surface under steady state condition and c) The interface temperature at the junction of the metals.arrow_forward
- A cylindrical storage tank with diameter of 4m and a length of 10 m will hold a fluid whose temperature must be maintained at 347k. in order to size the heater required for the tank the following worst-case scenario is considered: Ambient temperature=-20 wind speed=20m/s tank wall temperature=347k what size (kW) heater will be needed?arrow_forwardQ1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a fluid at 20 C. The convection heat- transfer coefficient is 15 W/m2 C. Determine the dimension of the block that it is just considered as lumped-capacity system. Calculate : (1) the time the center of the sphere reaches the half value of initial temperature and, (2) the heat loss from the block at that time.arrow_forwardQuestion 1:A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg=1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15oC and -20oC, respectively, ona cold winter day, what is the rate of heat loss throughthe glass? To reduce heat loss through windows, it iscustomary to use a double pane construction in whichadjoining panes are separated by an air space. If thespacing is 10 mm and the glass surfaces in contact withthe air have temperatures of (last two digit of your Registration number) oC and -15oC, what isthe rate of heat loss from a 1 m x 2 m window? Thethermal conductivity of air is ka=0.024 W/m.K.arrow_forward
- Can someone please help me with creating an excel spreadsheet to calculate heat transfer phenomenon from a cylindrical fuel rod to the coolant? The excel sheet needs to be able to calculate these 3 things: Heat generated in a fuel rod at a distance ‘r’ from the center; Total Heat generated in the Reactor; the maximum temperature in the fuel and the cladding surface temperature, for a fuel rod at a distance ‘r’ from the center. The fuel used in this will be UO2 and there is a thin layer of helium that will separate the fuel from the cladding material. The user input parameters will be: the thermal neutron flux at the core, thermal conductivity of fuel, thermal conductivity of helium, thermal conductivity of the cladding, thickness of the helium layer, thickness of the cladding, diameter of the fuel pellet, fuel rod location (r), Cylindrical Reactor Size, and the fuel enrichment. For the fluid the user input will be coolant temperature and the heat transfer coefficient.arrow_forwardPlate glass 5 mm thick at200°C is to be cooled fromb bothsides using air at 40°C. Ifs surfacecracks are to bea avoided determine them maximumvalue of convective heat transfer coefficient. Material properties are density = 2500 kg/m3, = specific heat 670 J/kgK. Thermal conductivity 0.744 W/mk. Also determine the time required in this to cool the plate to 80°C.arrow_forwardH.W1 Consider a person standing in a room. Determine the total rate of heat transfer from this person if the exposed surface area and temperature are 1.6m² and 29°C, respectively. Assume that the convection heat transfer coefficient is 6W/m².K and the emissivity of a person is 0.95. The air temperature in the room is maintained at 22°C at all times of the year. In summer, the wall and ceiling temperatures are observed to be 25°C, while in winter, they are 10°C. Ans: Qrotal =104.4 W In Summer Qrotal =231.3 W In Winterarrow_forward
- Q2/ A hot surface at 100 C is to be cooled by attaching 27778 copper fins (k=237 w/m.K), 3 cm long for each fin, 0.25 cm dia. to it. Temp. of surrounding air is 30 C and h=35 w/m2.K on the surface. Calculate the heat rate from the surface for a 1m X im section of the plate. Also, determine the effectiveness of the fins.arrow_forwardThermal jackets are typically put on cryogenicstorage tanks to minimize the heat transfer gainsfrom the surroundings. Consider a cylindercontainer that is 1.5 m long made from steel (k = 750W/m.K) with an inner diameter of 0.5 m and outerdiameter of 0.7 m. If the liquefied natural gas (LNG)inside the cylinder is maintained at 90 K, ambientconditions are Tamb = 20 °C, h = 7 W/m2.K. What is the required insulationmaterial to maintain the outer temperature of that jacket of 15 °C? Usethe end of the book and write your assumption with the right value.(Take a maximum allowed jacket thickness of Lins = 7 cm)arrow_forwardHeat Transfer Lesson The water will be heated from 10 (Degrees centigrade oC) to 90 (Degrees centigrade oC) while flowing through a smooth pipe with 1.5 cm inner diameter and 7 meters length.The entire surface of the pipe is equipped with an electric heater, which ensures uniform heating throughout.The outer surface of the heater is well insulated and therefore all heat generated in the heater in continuous operation is transferred to the water in the pipe.If the system provides 6 Liter / minute flow rate of hot water. (Thermophysical properties of water at 50 oC:ρ = 988 m3/kg, k= 0.6305 W/m oC, cp=4181 J/kg oC, Pr=3.628, μ= 0.0005471 kg/m.s ) a)Find the power of the resistance heater [W]. b)Calculate the inner surface temperature [oC] of the pipe at the outlet. c)Find the pressure drop [Pa]. d)Find the pump power [W] required to overcome this pressure drop.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license