Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.78P
(a)
To determine
The temperature distribution within the fin.
(b)
To determine
Heat transfer per unit length and comparison with value of assuming 1-D fin.
(c)
To determine
The temperature distribution and heat rate for different convection coefficient.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The composite wall of an oven consists of three materials, two of which are ofknown thermal conductivity, kA = 25 W/m ⋅ K and kC = 60 W/m ⋅ K, and knownthickness, LA = 0.40 m and LC = 0.20 m. The third material, B, which is sandwichedbetween materials A and C, is of known thickness, LB = 0.20 m, but unknownthermal conductivity kB. Under steady-state operating conditions, measurementsreveal an outer surface temperature of Ts,o = 20°C, an inner surface temperature ofTs,i = 600°C, and an oven air temperature of T∞ = 800°C. The inside convection coefficient h is known to be 25 W/m2 ⋅K. Neglecting convection transfer effect,what is the value of kB?
A section of a composite wall with the dimensions shown below has uniformtemperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA = 70 W/(m K), kB = 60 W/(m K), kc = 40 W/(m K) and kD = 20 W/(m K), determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces.
A gas filled tube has 2 mm inside diameter and 25 cm length. The gas is heated by an electrical wire of diameter 50 microns (o.05 mm) located along the axis of the tube. Current and voltage drop across the heating element are 0.5A and 4 volts, respectively. If the measured wire and inside tube wall temps are 175C and 150C respectively, find the thermal conductivity of the gas filling the tube.
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q2) A short fin is attached to a flat surface temperature T = 40 °C. Determine the fin temperature at 5 cm from the base and the rate of heat loss from the entire fin. Considering that the ambient air temperature Too = 20 °C, convection coefficient h = 50 w/m².°C, fin conduction coefficient k = 300 W/m.°C, fin dimensions (L = 7cm, W = 5cm, t = 2mm), Perimeter, P = 10 cm. 612223 T=40 °C X = 5 cm L = 7 cm h=50 Too=20 k-300 W = 5 cm = 2mmarrow_forwardHeat loss through an insulation (k = 0.05 W/m·C) is 125 W/m2.The temperature gradient across the insulation is 100 C. Find thethickness of the insulation.arrow_forward2. A pipe with: ID: 130mm OD: 165mm k=15 W/m?-K L= 2m is insulated with several materials, and convection on the inside and outside of the pipe is as follows. Oil inside is at 118°C and air outside is at 25°C KA or h 10.256 W/m2-K Material Thickness A 25mm В 2.369 W/m2-K 30mm C 0.257 W/m2-K 40mm h=120.3T2/3 (T in K) h=0.272/3 (T in K) Oil inside Air outside Determine the heat losses of the pipe, and what must be the temperature of the oil to decrease the heat losses by 20%?arrow_forward
- Two walls of cold storage plant are composed of an insulating material (k = 0.25 kJ/hr-m-°C), 100mm thick at the outer layer and material (k = 3.5 kJ/hr-m-°C), 15mm thick at inner layer. If the surface temperature at the cold side is 30 °C and hot side is 250 °C, find the heat transmitted per square meter.arrow_forwardFind the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K) not sufficient information 8 m 10 m 20 m 15 marrow_forwardA bar of thermal conductivity k = 140 W/m ⋅ K is of a trapezoidal cross section asshown in the schematic. The left and right faces are at temperatures Th = 100°Cand Tc = 0°C, respectively. Determine the heat transfer rate per unit bar lengthusing a finite difference approach with ∆X = ∆y = 10 mm. Compare the heat rate tothat of a bar of a 20 mm × 30 mm rectangular cross section where the height of thedomain is 20 mm.arrow_forward
- PROBLEM 3 In the given schematic of heat transfer for a wall, there is heat conduction through the wall and the outer surface of the wall is subject to both convection and radiation. T₁ = 308 K k = 0.3 W/m-K L = 3 mm -T₁ -ε = 0.95 111 Air Tsur = 297 K T = 297 K h = 2 W/m² K (Air) (a) Write the energy conservation equation for the system in terms of the three heat transfer modes. (b) Find the surface temperature Ts in °C.arrow_forward1. Temperatures are measured at the left-hand face and at a point 4 cm from the left-hand face of the planar wall shown in the figure below. These temperatures are T₁ = 45.3 °C and T* = 21.2 °C. The heat flow through the planar wall is steady and one dimensional. What is the value of T2 at the right-hand surface of the wall? TI T* 4 cm 10 cm T2arrow_forwardQ1/The thermal conductivity 14.4w/m.k for the block of stainless steel shown below is well insulated on the front and back surfaces, and the temperature in the block varies linearly in both the x- and y directions, Find: The heat fluxes and heat flows in the x- and y-directions. 5 cm 15°C 10°C -5 cm - 10 cm 5°C 0°C Q2-Consider a two layer composite wall of copper and Teflon as shown below. The copper has a thickness of 10cm but the thickness of the Teflon is to be determined. The temperature on the left boundary is equal to 200 C and on the right boundary 25C. Determine the thickness of the Teflon layer so that the heat flux is equal to 200W/m2. L2 T = 200C Te = 25 C L1 = 01m TA T3 %3D - 007 = 5 coper télon Tcarrow_forward
- Three (3) bricks, specifically A, B, and C were arranged horizontally in such a way that it can be illustrated as a sandwich panel. Consider the system to be in series and in the order of Brick A, Brick B and Brick C. The outside surface temperature of Brick A is 1,500℃ and 150 ℃ for the outside surface of Brick C. The thermal conductivities for Brick A, Brick B and Brick C, are 2 ?/? °? , 0.50 ?/? °? , 60 ?/? °?. The thickness of Brick A and Brick C are 50 cm and 22 cm. The rate of heat transfer per unit area is 1,000 ?/?2 . Determine the following: The thickness of Brick B in the unit of mm. Assume that all the conditions were retain except that the thickness of Brick B was increased to 800 mm, what is the new value for the rate of heat transfer per unit area in ???/ℎ? . ??2 please explain the principles to solve thisarrow_forwardMaterials expand when heated. Consider a metal rod of length L0 at temperature T0. If the temperature is changed by an amount ∆T, then the rod's length approximately changes by ∆L = ∝Lo∆T, where a is the thermal expansion coefficient and ∆ T is not an extreme temperature change. For steel, ∝ = 1.24 X 10- 5 0 c- 1. (a) A steel rod has length Lo = 40 cm at To = 40°C. Find its length at T = 90°C. (b) Find its length at T = 50°C if its length at To= 100°C is 65 cm. ( c) Express length L as a function of T if Lo = 65 cm at To = 100°C.arrow_forward#m 3 E D C F3 $ 4 R F Ac = 1m² V Too,1=1 K h₁ = 1 W/m²K (5) Consider a wall (as shown above) of thickness L=1 m and thermal conductivity k-1 W/m-K. The left (x=0) and the right (x=1 m) surfaces of the wall are subject to convection with a convectional heat transfer coefficient h = 1 W/m²K and an ambient temperature T.= 1 K. Heat generation inside the wall is q=1W/m³. You may assume 1-D heat transfer, steady state condition, and neglect any thermal contact resistance. Find T(x). 44 % 5 Q Search F5 T G T₁ B x=0 * A 6 q=1 W/m³ k= 1W/mK L=1m F6 Y H F7 & 7 T₂ x= 1 m U N Top 2 = 1 K h₂=1 W/m²K PrtScn F8 8 Home M F9 ( 9 K End F10 0 L PgUparrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license