A 1-D conduction heat transfer problem with internal energy generation is governed by the following equation: d'T è dr =0 where è = 5E5 and k = 32 If you are given the following node diagram with a spacing of Ax = .02m and know that T= 611K and T2 = 600K, write the general equation for these internal nodes in finite difference form and determine the m-K temperature at nodes 3 and 4. Insulated Ar For the answer window, enter the temperature at node 4 in Kelvin (K). Your Answer: Answer units

A 1-D conduction heat transfer problem with internal energy generation is governed by the following equation: d'T è dr =0 where è = 5E5 and k = 32 If you are given the following node diagram with a spacing of Ax = .02m and know that T= 611K and T2 = 600K, write the general equation for these internal nodes in finite difference form and determine the m-K temperature at nodes 3 and 4. Insulated Ar For the answer window, enter the temperature at node 4 in Kelvin (K). Your Answer: Answer units

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.55P

See similar textbooks

Similar questions

2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.
5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder (0.1 m diameter, thermal conductivity of 0.2 W/m K) with uniform internal heat generation. By dimensional analysis, determine the relation between the steady-state temperature at the center of the cylinder , the diameter, the thermal conductivity, and the rate of heat generation. Take the temperature at the surface as your datum. What is the equation for the center temperature if the difference between center and surface temperature is when the heat generation is ?
Heat flows through the wall in the following figure from the warm inside T, to the cooler The outside T, . In the center of the wall is a glass block of thickness t and thermal resistance R, . 2 thermal resistance of the wood and brick are R ,R, respectively. (a) wall, qw· The remainder of the wall is composed of two layers (wood and brick) each of thickness Find an expression for the steady state heat flow through the wood layer of the Determine the total resistance. (b) brick wood Rb Rw L glass Rg To TA
Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0. : Sketch a simple diagram for the temperature distribution in plane wall for a steady state one dimensional heat conduction, with heat generation. The surface temperature of the walls Ti and T2, for the cases Ti>T2, T1-T2, and T2>T1. The thickness of the wall may be taken as 2L
You are asked to estimate the maximum human body temperature if the metabolic heat produced in your body could escape only by tissue conduction and later on the surface by convection. Simplify the human body as a cylinder of L=1.8 m in height and ro= 0.15 m in radius. Further, simplify the heat transfer process inside the human body as a 1-D situation when the temperature only depends on the radial coordinater from the centerline. The governing dT +q""=0 dr equation is written as 1 d k- r dr r = 0, dT dr =0 dT r=ro -k -=h(T-T) dr (k-0.5 W/m°C), ro is the radius of the cylinder (0.15 m), h is the convection coefficient at the skin surface (15 W/m² °C), Tair is the air temperature (30°C). q" is the average volumetric heat generation rate in the body (W/m³) and is defined as heat generated per unit volume per second. The 1-D (radial) temperature distribution can be derived as: T(r) = q"¹'r² qr qr. + 4k 2h + 4k +T , where k is thermal conductivity of tissue air (A) q" can be calculated…
Problem 4 A cork board (k = 0.039W/m K) 3 cm thick is exposed to air with an average temperature T.. = 30°C with a convection heat transfer coefficient, h = 25 W/m².K. The other surface of the board is held at a constant temperature of 15°C. A volumetric heat generation of 5 W/m³ is occurring inside the wall. Assuming one dimensional conduction, write the governing equation and express the boundary conditions for the wall. (solve the equation is not required) Problom
Which formula is used to calculate the heat conduction in the AXIAL direction in a vertically located pipe segment whose inner and outer surfaces are perfectly insulated. Here r, is inner radius, r, outer radius, Tri pipe inner surface temperature, Tro pipe outer surface temperature, L is the length of the pipe, T the temperature on the lower surface, Ty the temperature on upper surface. Tu r; Tro r
under steady-state conditions. If you are given T1 = 200 °C and T2 = 164 °C, determine: a) the conduction heat flux, q,.cond, in m2 W from x = 0 to x = L b) if the dimensions of the triangle ares 15 mm and h 13 mm, calculate the heat transfer due to convection, q,y, in W at x = L Finsulation T2 T T = 20°C h = 500 W/m2.K Triangular Prism x L x 0 L= 50 mm k = 100 W/m-K
The wall (thickness L) of a furnace is comprised of brick material (thermal conductivity, k = 0.2 Wm¯' K'). Given that the atmospheric temperature is 0°C at both sides of wall, the density (p) and heat capacity (c) of the brick material are 1.6 gm cm³ and 5.0 J kg K¯l respectively. du Solve pc = k- subject to initial conditions as u(x,0) = x²(L – x). ốt Consider the case 2=- p² only.
1 . A long cylindrical shell outer radius R₂ = 2 cm is shown in cylindrical shell is temperature Ti=10 c° and outer wall at Constant temperature T₂ = 20 C° Calculate the temperature at r= 1.5 cm (Consider conduction only) Assumptions: system is Thermal in Given: The of inner and the figure. The radial + The differential The system is: J²T dr² r maintained at steady state conductivity, K = 22.5 w/mc, system follows Fourier's law of heat Heat loss in axial direction is negligible. JT dr radius Ri=1cm Length L=lom inner Wall Constant is maintained = 0 of is Ti RI R₂ constant. conduction. equation representing Tz
Write the finite difference form of the two dimensional steady state heat conduction equation with internal heat generation at a constant rate ‘g’ for a region 0.03m X 0.03m by using a mesh size ∆x=∆y= 0.01 m for a material having thermal conductivity 25 W/m.K and heat generation rate, 107 W/m3 . All the boundary surfaces are maintained at 10°C. Express the finite difference equations in matrix form for the unknown node temperatures.
Pls answer 4-10show complete step by step solution