Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 4, Problem 4.58P
(a).
To determine
We have to determine the unknown temperatures when
(b).
To determine
We have to access the effect of variation in h on the unknown temperatures and the heat rate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Problem 3: The composite wall shown in the figure below is 200mm H x 100mm wide. What is the
temperature at the surface between the G10 and the aluminum heatsink? Note: Answer should be to the
nearest thousandth of a degree.
Adiabatic
Wall
T. = 25°C
W
h = 45.
m²K
G10
Aluminum
Fiberglass
Heatsink
3mm
6mm
W
q" = 1200
m2
In a thermal power plant, a horizontal copper pipe of "D" diameter, "L" length and thickness 1.2 cm enters into the boiler that has the thermal conductivity as 0.37 W/mK. The boiler is maintained at 113C and temperature of the water that flows inside the pipe is at 29C. If the energy transfer (Q) is 118779 kJ in 7 hours.
Calculate:
4-Length of the pipe, if D = 0.017 L.
5-Pipe Diameter (in mm)
Q1/The thermal conductivity 14.4w/m.k for the block of stainless
steel shown below is well insulated on the front and back surfaces,
and the temperature in the block varies linearly in both the x- and
y directions,
Find: The heat fluxes and heat flows in the x- and y-directions.
5 cm
15°C
10°C
-5 cm -
10 cm
5°C
0°C
Q2-Consider a two layer composite wall of copper and Teflon as
shown below. The copper has a thickness of 10cm but the
thickness of the Teflon is to be determined. The temperature on
the left boundary is equal to 200 C and on the right boundary 25C.
Determine the thickness of the Teflon layer so that the heat flux
is equal to 200W/m2.
L2
T = 200C
Te = 25 C
L1 = 01m
TA
T3
%3D
- 007 = 5
coper
télon
Tc
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.arrow_forward3.112 A metal rod of length 21, diameter D. and thermal conductivity is inserted into a perfectly insulating wall, exposing one-half of its length to an air stream that is of temperature and provides a convection co- efficient h at the surface of the rod. An electro- magnetic field induces volumetric energy generation at a uniform rate q within the embedded portion of the rod. T=20°C h=100 W/m²K Rod, D. & T L 50 mm D-5 mm 25 W/m-K q=1 x 100 W/m² (a) Derive an expression for the steady-state tempera- ture 7, at the base of the exposed half of the rod. The exposed region may be approximated as a very long fin. (b) Derive an expression for the steady-state tempera- ture T at the end of the embedded half of the rod. (c) Using numerical values provided in the schematic plot the temperature distribution in the rod and de- scribe key features of the distribution. Does the rod behave as a very long fin?arrow_forwardExample 4.10 A thin brass pipe, 3 cm in outside diameter, carries hot water at 85°C. It is proposed to place 0.8 mm thick straight circular fins on the pipe to cool it. The fins are 8 cm in diameter and are spaced 2 cm apart. It is determined that h will equal 20 W/m².°C on the pipe and 15 W/m².°C on the fins, when they have been added. If To = 22°C, compute the heat loss per meter of pipe before and after the fins are added.arrow_forward
- The steel pipe has an internal radius of 50 mm., a thickness of 5 mm. and a length of 5 m. Inside the pipe, hot fluid with temperature 80 C flows inside the pipe and cold fluid with temperature 20 C flowing outside the pipe. Let k=285 W/mC and hi= 25 W/mC, ho= 10 W/mC. Find 4.1) Heat Transfer Rate (Q) 4.2) Temperature on both inner and outer tube surfaces...arrow_forwardIn 2012, a new fiber-optic cable of handling 40,000 telephone calls simultaneously was laid under the Pacific Ocean from California to Japan, a distance of 13,300 km. The cable was unreeled from shipboard at a mean temperature of 22oC and dropped to the Ocean floor having a mean temperature of 5oC. The coefficient of linear expansion of the cable is 75×10-6 /degree celsius. Determine the length of cable that must be carried on the ship to span the 13,300 Km. Also, find the percent change in lengtharrow_forwardHomework O H.W. 1: The walls of a refrigerator are typically constructed by sandwiching a layer of insulation between sheet metal panels. Consider a wall made from fiberglass insulation of thermal conductivity k; = 0.046 W/m.K and thickness L, = 50 mm and steel panels, each of thermal conductivity k, = 60 W/m.K and thickness L, = 3 mm. If the wall separates refrigerated air at T = 4 C from ambient air at T,. = 25 C, what is the heat gain per unit surface area? Coefficients associated with natural convection at the inner and outer surfaces may be approximated as h, = h, = 5 W/m?.K. %3D %3D L; = 0.050 m K K Lo = 0.003 m Refrigerated air Ambient air Too.i = 4°C hi = 5 W/m2-K To,o = 25°C ho = 5 W/m2-K %3D Panel (2) kp = 60 W/m-K Insulation k; = 0.046 W/m-K 22 Warith Alanbiyaa (Dr. ALI M) Heat Transfer Page 11 ofarrow_forward
- Below is a diagram of a pipe with 5 m radius, temperature of 5000 K, and k = 450 W/m-K. The pipe is covered by a steel that is 1.8 m thick with k = 17 W/m-K. The temperature inside is 5000 K while the temperature outside is 800 K. TB = 800 K TA = 5000 K k = 450 W/m-K K = 15 W/m-K Answer the following: 1. Calculate the system's heat loss per unit length (W/m²). 2. Calculate the temperature between the pipe and the steel (temperature in K). 5 m 1.8 m/arrow_forwardThe composite wall of an oven consists of three materials, two of which are ofknown thermal conductivity, kA = 25 W/m ⋅ K and kC = 60 W/m ⋅ K, and knownthickness, LA = 0.40 m and LC = 0.20 m. The third material, B, which is sandwichedbetween materials A and C, is of known thickness, LB = 0.20 m, but unknownthermal conductivity kB. Under steady-state operating conditions, measurementsreveal an outer surface temperature of Ts,o = 20°C, an inner surface temperature ofTs,i = 600°C, and an oven air temperature of T∞ = 800°C. The inside convection coefficient h is known to be 25 W/m2 ⋅K. Neglecting convection transfer effect,what is the value of kB?arrow_forwardExample: a fin pin with diameter D = 0.03m is fixed between two walls at temperature 100 °C. Assuming that the ambient air temperature is 20 °C , fin length L= 0.2m, coefficient of heat transfer k = 300 w/m.c and h = 100 w/m2.c. Find the fin temperature at x = 0.lm and calculate total heat transfer rate to this point x = 0.01m. Too = 20 °Carrow_forward
- During a wall heat flux measurement, at the instantaneous time t, we obtained the following values: Q = 30/ Tal = 20 °C Tse = 5°C Calculate the instantaneous U-Value at time t m²K (Note: R₂ = 0.13 W and R = 0.04³)arrow_forwardConduction 1. A thermodynamic analysis of a proposed Brayton cycle gas turbine yields P= 5 MW of net power production. The compressor, at an average temperature of T. = 400°C, is driven by the turbine at an average temperature of T₁ = 1000°C by way of an L = 1m-long, d= 70mm - diameter shaft of thermal conductivity k = 40 W/m K. Compressor min T Combustion chamber Shaft L Turbine Th out (a) Compare the steady-state conduction rate through the shaft connecting the hot turbine to the warm compressor to the net power predicted by the thermodynamics- based analysis. (b) A research team proposes to scale down the gas turbine of part (a), keeping all dimensions in the same proportions. The team assumes that the same hot and cold temperatures exist as in part (a) and that the net power output of the gas turbine is proportional to the overall volume of the device. Plot the ratio of the conduction through the shaft to the net power output of the turbine over the range 0.005 m s Ls 1 m. Is a…arrow_forwardQUESTION 1 a) A silicon chip is cooled by passing nanocoolant through microchannels etched in the back of the chip, as shown in Figure Q1. The channels are covered with a silicon cap. Consider a 11 mm and 11 mm square chip in which N = 50 rectangular microchannels, each of width W = 40 µm and height H = 160 µm have been etched. Nanocoolant enters the microchannels at a temperature T; = 290 K, and a total flow rate of 0.005 kg/s. The chip and cap are maintained at a uniform temperature of 340 K. Assuming that the flow in the channels is fully developed and all the heat generated by the circuits on the top surface of the chip is transferred to the nanocoolant, determine the rate of heat transfer through the rectangular microchannel. Assume nanocoolant as water properties at 25 °C. 11 mm 1 T. Circuits generating power W. 11 mm Chip, T; Сар, Т, H W Figure Q1 b) A desktop computer is to be cooled by a fan. The electronic components of the computer consume 100 W of power under full-load…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Thermal Radiation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=FDmYCI_xYlA;License: Standard youtube license