Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.27P
(a)
To determine
The heat rate from a single channel per unit length of the platen normal to the page.
(b)
To determine
The outer surface temperature of the cover plate.
(c)
To determine
The effects that changing the center line spacing will have on
The affect of insulating the lower surface on
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 10 ft length of pipe with an inner radius of 1 in and outer radius of 1.25 in has an outer surface temperature of 250 F. The heat transfer rate is 30,000 BTU/hr. Find the interior surface temperature. Assume k = 25 BTU/hr-ft-F.
In a thermal power plant, a horizontal copper pipe of "D" diameter, "L" length and thickness 1.2 cm enters into the boiler that has the thermal conductivity as 0.37 W/mK. The boiler is maintained at 113C and temperature of the water that flows inside the pipe is at 29C. If the energy transfer (Q) is 118779 kJ in 7 hours.
Calculate:
4-Length of the pipe, if D = 0.017 L.
5-Pipe Diameter (in mm)
Conduction
1. A thermodynamic analysis of a proposed Brayton cycle gas turbine yields P=
5 MW of net power production. The compressor, at an average temperature
of T. = 400°C, is driven by the turbine at an average temperature of T₁ =
1000°C by way of an L = 1m-long, d= 70mm - diameter shaft of thermal
conductivity k = 40 W/m K.
Compressor
min
T
Combustion
chamber
Shaft
L
Turbine
Th
out
(a) Compare the steady-state conduction rate through the shaft connecting the hot
turbine to the warm compressor to the net power predicted by the thermodynamics-
based analysis.
(b) A research team proposes to scale down the gas turbine of part (a), keeping all
dimensions in the same proportions. The team assumes that the same hot and cold
temperatures exist as in part (a) and that the net power output of the gas turbine is
proportional to the overall volume of the device. Plot the ratio of the conduction through
the shaft to the net power output of the turbine over the range 0.005 m s Ls 1 m. Is a…
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5. Consider a carton of milk that is refrigerated at a temperature of Tm = 5 °C. The kitchen temperature on a hot summer day is T- -30 °C. If the four sides of the carton are of height and width L = 200 mm and w= 100 mm, respectively, determine the heat transferred to the milk carton as it sits on the kitchen counter for durations of t=10 s, 60 s, and 300 s before it is returned to the refrigerator. The convection coefficient associated with natural convection on the sides of the carton is h = 10 W/m²K. The surface emissivity is 0.90. Assume the milk carton temperature remains at 5 °C during the process. Your parents have taught you the importance of refrigerating certain foods from the food safety perspective. Comment on the importance of quickly returning the milk carton to the refrigerator from an energy conservation point of view.arrow_forwardIn a thermal power plant, a horizontal copper pipe of "D" diameter, "L" length and thickness 1.9 cm enters into the boiler that has the thermal conductivity as 0.37 W/mK. The boiler is maintained at 102 °C and temperature of the water that flows inside the pipe is at 34°C. If the energy transfer (Q) is 100735 kJ in 7 hours. Determine the Heat transfer rate, Surface area of the pipe and Diameter & Length of the pipe, if D = 0.015 L. Surface Area of the Pipe (m2) Pipe Length (in m) Pipe Diameter (in mm)arrow_forwardIn a thermal power plant, a horizontal copper pipe of "D" diameter, "L" length and thickness 1.9 cm enters into the boiler that has the thermal conductivity as 0.37 W/mK. The boiler is maintained at 102 °C and temperature of the water that flows inside the pipe is at 34°C. If the energy transfer (Q) is 100735 kJ in 7 hours. Determine the Heat transfer rate, Surface area of the pipe and Diameter & Length of the pipe, if D = 0.015 L .arrow_forward
- Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.arrow_forwardA thick-walled cylindrical tubing of hard rubber (k=0.151 W/m*K) having an inside radius of 5 mm and an outside radius of 20 mm is being used as a temporary cooling coil in a bath. Ice water is flowing rapidly inside, and the inside wall temperature is 275 K. The outside surface temperature is 300 K. A total of 20 W must be removed from the bath by the cooling coil. How many meter of tubing are needed?arrow_forwardSteam at 350 °C flows through the stainless steel pipe with k=26 W/m.°C. The inner and outer diameters of the stainless steel pipe are 6.0 cm and 7.0 cm, respectively. The pipe is insulated from the outside with a 4.0 cm thick glass wool (k= 0.038 W/m.°C) and then a 3.0 cm thick k=0.25 W/m.K material. The insulated pipe is in the environment at 20 °C. The heat loss from the pipe occurs only by [natural convection+radiation]. Film heat transfer coefficient including the effects of [natural convection+radiation] in the insulated pipe is 30 W/m². is C. Calculate the heat transferred per unit pipe length since the film heat transfer coefficient defined according to the inner area of the pipe is 110 W/m².°C.arrow_forward
- An incompressible fluid flows through a rectangular cross section duct, with width much larger than height of the cross section. The duct surface is heated at a uniform rate along its length. If the centreline of the flow is along the centre of the duct where y = 0, the distance from the centreline to the surface of the duct is b = 25 mm, and the thermal conductivity of the fluid is 0.6 W/mK, what is the local heat transfer coefficient in the developed region of the flow? Give your answer in W/m2K to 1 decimal place.arrow_forwardAn incompressible fluid flows through a rectangular cross section duct, with width much larger than height of the cross section. The duct surface is heated at a uniform rate along its length. If the centreline of the flow is along the centre of the duct where y = 0, the distance from the centreline to the surface of the duct is b = 25 mm, and the thermal conductivity of the fluid is 0.6 W/mK, what is the local heat transfer coefficient in the developed region of the flow? Give your answer in W/m2K to 1 decimal place. I AM POSTIING THIS AGAIN. PLEASE STOP ? COPY FROM INTERNET AND SEND RANDOM SOLUTION. HINT THE FINAL ANSWER IS 38.4 But i need step by step solution. if you don't get this value don't send it please, reject and add the creditarrow_forwardWhen a long section of a compressed air line passes through the outdoors, it is observed that the moisture in the compressed air freezes in cold weather, disrupting and even completely blocking the air flow in the pipe. To avoid this problem, the outer surface of the pipe is wrapped with electric strip heaters and then insulated. . Consider a compressed air pipe of length L = 6 m, inner ra- dius r₁ = 3.7 cm, outer radius r₂ = 4.0 cm, and thermal con- ductivity k = 14 W/m - °C equipped with a 300-W strip heater. Air is flowing through the pipe at an average temperature of -10°C, and the average convection heat transfer coefficient on the inner surface is h = 30 W/m². °C. Assuming 15 percent of the heat generated in the strip heater is lost through the insula- tion, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the pipe, (b) obtain a relation for the variation of temperature in the pipe material by solving the…arrow_forward
- Find the (1) heat flow rate in Watts (W) and (2) interface temperatures through the composite wall as shown in the figure. The exposed surface of wall A has a temperature of 400°C while that of wall D is 60°C. Assume one dimensional flow and take KA=150 W/m-°C, KB= 30W/m-°C, KC= 65W/m-°C, KD= 50W/m-°C. Also take Xa=3cm, xb= xc=8cm and xd= 5cm.arrow_forwardFluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.arrow_forwardQ1 (a) The temperature at the inner and outer surfaces of a boiler wall made of 25 mm thick steel and covered with an insulating material of 15 mm thickness are 350 °C and 600 °C respectively. If the thermal conductivities of steel and insulating material are 68 W/m°C and 0.126 W/mC respectively, determine the rate of flow through the boiler wall. (AT)overall Q = ΣRtharrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license