Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 4, Problem 4.32P
(a)
To determine
The fin heat rate and junction temperature for base materials aluminum and stainless steel.
(b)
To determine
The fin heat rate and junction temperature for base materials aluminum and stainless steel with thermal contact resistance.
(c)
To determine
To plot: Heat rate as a function of convection coefficient.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
An eyed plate & pin is assembled as illustrated and are subjected to an opposing force of 10KN.
The rod diameter & plate thickness is 6mm. The width of the plate is 20mm. A hole to which the pin is
inserted is 8mm in diameter is located at the center of the plate. The plate is made of annealed SAE 1025
& the pin is high-heat oil quenched SAE 1095.
(a) Determine if the assembly is safe to use; otherwise
(b) Determine the safe load of the assembly.
A composite component is comprised of a tube and a concentric rod running inside it, both
with a length of 1.5 meters. The tube is made of copper and has inner and outer diameters
of 60 mm and 100 mm, respectively, a coefficient of thermal expansion and elastic
modulus of 17 x10-C and 117 GPa, respectively. The rod is made of aluminium with a
diameter, coefficient of thermal expansion and elastic modulus of 50 mm, 23 ×10-°C and
80 GPa, respectively. If the composite is exposed to a temperature rise of 120°C,
determine:
1
The sense and magnitude of the stresses induced in the composite if it is not restrained.
The sense and magnitude of the stresses induced in the composite if it is partially restrained
with an allowed free expansion of 0.3 mm.
For aesthetic purposes, you are to fit a metal rod into a stainless-steel hole for your house's design. The hole is 9.988 mm in diameter. If the rod is to be heated so that it will fit into the hole, what will be the temperature in °C?
Assume:
Your house's temperature is 25°C
The length of the rod is around 10 mm.
Linear coefficient of the metal rod is 4.5×10-6°C and for the stainless steel is 16×10-6°C
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- After a thorough derivation by Doraemon to establish an equation for cylindrical fuel rod of a nuclear reactor. Here he was able to come up an equation of heat generated internally as shown below. 9G = 9. where qG is the local rate of heat generation per unit volume at radius r, ro is the outside radius, and qo is the rate of heat generation per unit volume at the centre line. Calculate the temperature drop from the centre line to the surface for a 2.5 cm outer diameter rod having k = 25 W/m K, if the rate of heat removal from the surface is 1650 kW/m² А) 619°C В 719 °C C) 819 °C D) 919 °C E 1019 °C F None of thesearrow_forwardNuclear fuel rods. A typical nuclear fuel rod contains circular uranium oxide (UO2) fuel pellets 10 mm in diameter and 5-mm thick stacked in a column to a length of 4 m inside a thin zirconium alloy tube, as shown below. The pellets generate heat uniformly throughout their volume due to nuclear fission, with a power density a (i.e., the heat power produced per unit volume of the pellet) that depends on their 235U enrichment. This heats up the water in the reactor to produce steam to drive the turbine. Assuming that the rim of the fuel pellet is maintained at a constant temperature Trim due to water cooling, show that the steady-state temperature profile T(r), where r is the radial distance from the centre of the pellet and fuel rod, 4. P(R? -r²; is given by: T(r) = Tim + 4k where k is the thermal conductivity of the pellet and R is its radius. partial stacked column of fuel pellets in rodarrow_forwardEXAMPLE 3 Steam at a temperature of 300 °C flows through a steal pipe, k= 14.9 W/m.K of 60 mm inside diameter and 80 mm outside diameter. The convection coefficient between the steam and the inner surface of the pipe is 500 W/m? K, while that between the outer surface of the pipe and the surroundings is 25 W/m2 .K the temperature of the surroundings air is 25 C. -What is the heat loss per unit length of pipe?arrow_forward
- Please solve asap, Will provide helpful ratings for complete solution. Thank u A double-glazed window is constructed such that it has 5 mm thick glass as the inside layer, 4 mm layer of gas, and finally 5 mm thick glass as the outer layer. Which have thermal conductivies of 0.7, 2.120, and 5.9 W m-1 K-1, respectively. Calculate the heat loss per unit area, Wm-2 through the glass if the inside temperature of the glass is 11.09 °C and the outside temperature is 6.47 °C Report your answer to 2 decimal places.arrow_forwardc) A steel pipe of 100 mm bore, and 10 mm bore thickness, carrying dry saturated steam at 28 bars, is insulated with a 40 mm layer of moulded insulation. This insulation in turn is insulated with a 60 mm layer of felt. The atmospheric temperature is 15 °C. Calculate: (i) the rate of heat loss by the steam per metre pipe length. (ii) the temperature of the outside Dimensions in mm surface.zzzzzzz h₂-15 W/m²K Steel k₁=50 W/mK AVALEHT Ø100 1₂ " Steam 28 bar h-550 W/m²K, Inner heat transfer coefficient = 550 W/m² K Outer heat transfer coefficient = 15 W/m² K Thermal conductivity of steel = 50 W/m K Thermal conductivity of felt = 0.07 W/m K Moulded insulation Felt Moulded insulation K₂=0.09 W/mK Thermal conductivity of moulded insulation = 0.09 W/m 40 10. A 60 15°C Felt K₁=0.07 W/mK zzzzzzzzarrow_forwardLet's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential energy lost in the drop could be converted to thermal energy used to heat the copper from an initial temperature of 25 degrees celsius, what would the final temperature of the copper wafer? Would the answer be different if the wafer has a mass greater than 3 grams? Note: the specific heat of copper is 387 J/(kg*K). The temperature is between 25.8 and 26.0 degrees celsius, yes the bigger the mass the greater the energy. O The temperature is between 25.6 and 25.8 celsius, answer does not depend on mass. O The temperature is between 25.0 and 25.2 celsius, answer does not depend on mass. O The temperature is 25.5 and of course the more mass something has the greater energy will be needed to raise the temperature. The temperature is 26.2 and if the mass is doubled so will be the change in temperature. O The temperature is 25.9 degrees celsius and the answer does not depend on mass. O The…arrow_forward
- A mechanic needs to remove a tight fitting pin of material A from a hole in a block made of material B. The machinist heats both the pin and the block to the same high temperature and removes the pin easily. What statement relates the coefficient of thermal expansion of material A to that of material B?arrow_forwardTwo balls (A and B) are made of the same material, heated to the same temperature and allowed to cool in the same medium "same h", when the diameter ratio (D/Dg = 2.0), then the cooling rate ratio (Q/QR) will bearrow_forward1. A large stainless steel plate with 2 mm thickness and thermal conductivity, k = 15 W/mK generates heat uniformly at a rate of 3 x 107 kW/m². If the surface temperature on both sides of the plate are 100°C; ) Write the governing equation for the case above and state the assumptions; (11) Obtain the temperature distribution expression by solving the goveming equation; (iii) Determine the maximum temperature inside the plate; (iv) Sketch the temperature profile if one of the surfaces are insulated.arrow_forward
- Example 2.10 Consider a 25 mm x 25 mm x 1 mm thick silicon die attached to a same size 2 mm-thick copper cap through a 0.1 mm thick thermal interface material (TIM) as shown in Figure 2.1. Convection heat transfer coefficient on the top side of the copper cap is 2500 W/m²°C. If thermal conductivity of silicon, copper, and thermal interface material are 125, 390, and 5 W/m°C, respectively, what is the total thermal resistance from the active (bottom) side of the silicon die to outside ambient?arrow_forwardMica sheet of 0.15 m diameter and has thickness of 0.005m is subjected to heater with a supply of 28W power. Cold water is circulated around the specimen with a temperature of 30°C; calculate the thermal conductivity of the specimen?arrow_forwardplease make it 1 paragraph in the abstract below, with the journal name Optimizing the thermal management system of PCM fin-structured Li-ion batteries under mechanical vibration conditions: A comparative study because I have difficulty combining can you please ask for help to try the writing below, so that the results are maximized The thermal management of battery systems using Phase Change Materials (PCM) commonly faces challenges due to the low thermal conductivity of PCM. This study introduces innovative fin structures comprising longitudinal fins and cylindrical rings to enhance heat transfer. Comparative experiments are initially designed to assess the thermal performance of various Battery Thermal Management Systems (BTMS). Results indicate that the PCM-Fin system outperforms both the pure battery system and the PCM system. Numerical simulations, validated with experimental data, uncover the underlying mechanisms. The fin structures not only increase the heat transfer area…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license