Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 4.11P
To determine
The rate of heat transfer between two particles.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The surface temperature of the hot side of the furnace wall is 1200°C. It is desired to maintain the outside of the wall at 38°C. A 152 mm of refractory silica is used adjacent to the combustion chamber and 10 mm of steel covers the outside. What thickness of insulating bricks is necessary between refractory and steel, if the heat loss should be kept at 788 W/m²? Use k = 13.84 W/m-K for refractory silica; 0.15 for insulating brick, and 45 for steel.
Badly needed asap. I will rate helpful. Thank you in advance.
How is storage modulus and loss modulus relate with diffussivity of a drug molecule pass through a gel? Does higher storage modulus means lower difussivity?
The heat exchange between two walls coated with silver on sides facing each other
is by radiation only. The contents of the bottle are at 100°C. The ambient
temperature is 14°C. The emissivity of silver is 0.02. Calculate the heat loss. If the
inner diameter of the thermos bottle is 10 cm, calculate approximately the outer
diameter of the thermos if the thickness of the cork insulation is such as to achieve
the same heat transfer. Thermal conductivity of cork is 0.042 W/m °C
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- If a heat transfer coefficient of 2.84 W l(m2 • K) exists on each of the two inside faces of two sheets of 6.35-mm-thick glass separated by an air gap, calculate the gap that can be used such that the rate of heat transfer by conduction through the air gap equals the rate of heat transfer by convection. What is the rate of heat transfer if this gap is exceeded. The thermal conductivity of air of 0.0242 WI (m . K). Solve for temperature of 20°C and 12°C on the outside surfaces of the glass. Would the calculated gap change in value for different values of the surface temperatures? Would there be any advantage to increasing the gap beyond this calculated value?arrow_forwardA solid sphere made of polished copper has a diameter of 2 cm and is at 100 C. We now expose the solid sphere to are at 50 C and 1 atm. Use the lumped capacitance method to plot the temperature of the solid sphere versus time after five minutes of exposure. The air is quiescent.arrow_forwardThe heat transfer from a 50mm diameter incandescent bulb at 127°C to 27°C quiescent air is [ use the data; v=7.076x10 m² /s, Pr 0.697,k = 0.03003 W/mK.]arrow_forward
- QUESTION 3 A rectangular window in a home has a length of 1.5 m and a height of 0.80 m. If the window allows heat to escape from the home at a rate of 2,000 watts, how thick must the window be if the inside temperature of the home is 220 c and the outside temperature is 3.0°C? (Assume that the coefficient of thermal conduction of glass is 0.80 W/mK.) а. 7.1 mm b. 11 mm C. 9.1 mm d. 124 mm e. 8.1 mmarrow_forwardA plate is maintained at 74°C and this surface is facin an air having temperature of 30°C, then what will be th value of coefficient of volumetric expansion ß?arrow_forwardA 10cm ball made of tungsten is to be heated from 100C to an average temperature of 150C in 30 minutes. Determine: (a) the total amount of heat that needs to be transferred to the ball; (b) the average rate of heat transfer to the ball; (c) the average heat flux S中钨在线 chinatungsten.com Blank Balls Polished Balls Punching Balls Bearing Balls Valve Balls Non-magnetic Balls (在arrow_forward
- The surface temperature of the hot side of the furnace wall is 1200°C. It is desired to maintain the outside of the wall at 38°C. A 152 mm refractory silica is used adjacent to the combustion chamber and 10 mm of steel covers the outside. What thickness of insulating bricks is necessary between refractory and steel, If the heat loss should be kept at 788 W/m2? use k = 13.84 W/m-K fro refractory silica; 0.15 for insulating brick, and 45 for steel. O 260 mm 280 mm O 240 mm 220 mmarrow_forwardA brass rod 100 mm long and 5 mm in diameter extends horizontally from a casting at 200 °C. Conductivity k=133 W/m/K. The rod is in an air environment with To = 20 °C and h = 30 W/m²/K. What is the temperature of the rod 25, 50, and 100 mm from the casting?arrow_forwardA black thermocouple measures the temperature in a chamber with black walls. If the air around the thermocouple is at 20°C, the walls are at 100°C, and the heat transfer coefficient between the thermocouple and the air is 15 W/m?K, what temperature will the thermocoule read?arrow_forward
- A sample of lead has a mass of 31.00 kg and a density of 1.130 x104 kg/m3 at 0°C. (Assume the average linear expansion coefficient for lead is 2.900 x10-5(°C−1).) What is the mass of the sample of lead at 95.00°C?arrow_forwardCalculate the heat transfer between two (50*40 cm) parallel plates at constant temperatures of 71 = 100 K and 72 = 50 K that are L = 1 cm apart, assuming the emissivity (r) is 0.6 according to the following conditions. 1. The parallel plates filled with atmospheric air assume the thermal conductivity at the average temperature of 250 K is k=0.021 Heat direction Air Space * 24140 Heat direction Super-insulation W/m °C for air, Stefan-Boltzmann constant is 5.67*10*W/m².K' 2. The parallel plates are filled with super-insulated material and have an apparent thermal conductivity of 0.00004 W/m - °C.arrow_forward(a) If the cost of producing the hot water is $0.10 per kWh, what is the representative daily costof heat loss from an uninsulated pipe to the air per meter of pipe length? The convectionresistance associated with water flow in the pipe may be neglected.(b) Determine the savings associated with application of a 10-mm-thick coating of urethaneinsulation (k = 0.026 W/m-K) to the outer surface of the pipe.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license