Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.79P
To determine
The temperature distribution for the fin and heat rate. Contribution of radiation and convection heat rate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
the hot combustion gasses of a furnace are separated from the ambient air and its surroundoing which are at 25c, by a brick wall 0.15 meter thick has a thermal conductivity of 1.2 w/(m-k) and a surface emissivity of 0.8. under steady state condition and outer surface temperature of 100c is measured. the convection heat transfer to the air adjoining this surface is characterized by a convection of 20 /(m-k), what is the inner temperature?
A cylinder with 15 mm radius, contains
an electric resistance heater, is located
in an oil of temperature 30 °C, the power
per unit length required to maintain a
uniform surface temperature of 100 °C
is 30 KW/m. Then the convection
coefficient is:
Select one:
a. 4.55 W/m2.K
b. 4.55 W/m.K
c. 5.45 W/m2.K
d. 4.45 W/m.K
e. None of the mentioned
A plane wall of thickness 8cm and thermal conductivity k=5W/mK experiences uniform volumetric heat generation, while convection heat transfer occurs at both of its surfaces (x= -L, x= + L), each of which is exposed to a fluid of temperature T∞ = 20˚C. The origin of the x-coordinate is at the midplane of the wall. Under steady-state conditions, the temperature distribution in the wall is of the form T(˚C) = a + bx - cx^2, where x is in meters, a =86˚C, b = -500˚C/m, and c=4459.
1) Heat Flux Entering the wall is ?
2) Temperature at the left face is /
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 2.3 The shield of a nuclear reactor is idealized by a large 25-cm-thick flat plate having a thermal conductivity of . Radiation from the interior of the reactor penetrates the shield and there produces heat generation that decreases exponentially from a value of at the inner surface to a value of at a distance of 12.5 cm from the interior surface. If the exterior surface is kept at 38°C by forced convection, determine the temperature at the inner surface of the field. Hint: First set up the differential equation for a system in which the heat generation rate varies according to .arrow_forwardA constant thermocouple wire of 0.4 mm dia is to be used to measure a temperature of 600°C. The wire is initially at 35*C. If the thermocouple should read 595°C in 2 seconds, determine the value of convection coefficient required. Density 8922 kg/m3, cp 410 J/kgk: Thermal conductivity = 22.7 W/mK.arrow_forwardA solid circular rode of 40 cm long and 4 cm diameter is subjected to a uniform temperature at the circular surface of one of its ends of 100 °C. The surface of other end are subjected to free convection with surrounding air with a convection coefficient of h = 10 W/(m². °C) and air temperature of 30 °C. Lateral surface is insulated. Use three linear elements to find the temperature along the rod, and the energy entered at the end of constant temperature. The thermal conductivity of the rod is K= 60 W/(m. °C K)arrow_forward
- A piece of beef steak 5 cm thick will be frozen in the freezer room -25 ° C. This product has a moisture content of 73%, a density of 970 kg / m, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 10 W / (m² K). tf =arrow_forwardThe wall (thickness L) of a furnace, with inside temperature 800° C, is comprised of brick material (thermal conductivity = 0.02 W m-! K-')). Given that the wall thickness is 12 cm, the atmospheric temperature is 0° C, the density and heat capacity of the brick material are 1.9 gm cm-3 and 6.0 J kg~1 K-l respectively, estimate the temperature profile within the brick wall after 2 hours. Solve the partial differential equation ()-~ ƏT ƏT subject to the initial condition T(x,0) = 800 sin ; 2L %3D and boundary conditions at the inner (z = L) and outer (r = 0) walls of T = 0 x =0 at and ƏT I = L at Find the temperature profile at T = 7200 seconds = 2 hours.arrow_forward3. A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2 ° C. After 11 hours in the freezing medium -30 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder. h = Answer W / (m² K).arrow_forward
- Transient Heat Conduction Cooking a Thanksgiving turkey is an art form and, if your skills in the kitchen are like mine, it is sometimes more of a mystical, elusive art form. Thankfully, science also has much to contribute in the kitchen as well as the laboratory. Let us consider the change in temperature of a common, 20-lb holiday fowl as it is cooked in a convection oven. To simplify the analysis, let's assume the bird can be modeled as a uniform sphere of radius 7.0 in. with a specific heat of 3.53 kJ/kg-K. Moreover, the turkey will be assumed to have a uniform temperature, T, throughout that will change with time as it is cooked according to the following relationship: 。 + (To - T∞)ept T(t) = T∞ + where To is the initial temperature of the turkey, T∞, is the oven temperature, V is the volume of the turkey, As is the surface area of the turkey, and h is the convection coefficient for the scenario which is 11.3 W/m²-K. If the oven is set to 325 °F and the initial temperature of the…arrow_forwardA piece of beef steak 7 cm thick will be frozen in the freezer room -40 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 10 W / (m² K). t f = ...... hour.arrow_forwardA piece of beef steak 7 cm thick will be frozen in the freezer room -40 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 15 W / (m² K). t f = Answerhour.arrow_forward
- A piece of beef steak 5 cm thick will be frozen in the freezer room -30 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 10 W / (m² K). t f =arrow_forward(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = = W 3 m. k . Ay m-1, n m, n | Δx=" m, n+1 m, n-1 The side insulatedarrow_forward1- The energy transferred from the anterior chamber of the eye through the cornea varies considerably depending on whether a contact lens is worn. Treat the eye as a spherical system and assume the system to be at steady state. The convection coefficient ho is unchanged with and without the contact lens in place. The cornea and the lens cover one-third of the spherical surface area. T he T h Anterior chamber Contact lens Cornea are as follows: Values of the parameters representing this situation r 10.2mm, r 12.7 mm, r3= 16.5 mm, Teoj= 37°C, Teoo = 21°C, ki = 0.35 W/m.K, k2 0.80 W/m.K, h 12 W/m2.K, ho 12 W/m2.K. (a) Construct the thermal circuits, labeling all potential and flows form the systems excluding the contact lens and including the contact lens. Write resistance elements in terms of appropriate parameters (b) Determine the heat loss from the interior chamber with and without the contact lens in place (c) Discuss the implication of your results.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license