Statistics for Engineers and Scientists
4th Edition
ISBN: 9780073401331
Author: William Navidi Prof.
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 6.9, Problem 6E
To determine
Check whether there is evidence to conclude that the mean rate differs between the two catalysts.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In the production of synthetic motor lubricant from coal, a new catalyst has been discovered that seems to affect the viscosity index of the lubricant. In an experiment consisting of 23 production runs, 11 used the new catalyst and 12 did not. After each production run, the viscosity index of the lubricant was determined to be as follows.
With catalyst
4.0
4.4
2.6
1.2
3.9
4.2
2.8
3.2
4.1
2.1
1.6
Without catalyst
3.3
2.3
3.7
3.0
4.3
2.7
4.5
1.5
3.6
2.5
2.2
3.4
The two samples are independent. Use a 0.01 level of significance to test the null hypothesis that the viscosity index is unchanged by the catalyst against the alternate hypothesis that the viscosity index has changed.
1.) Find the sample test statistic. (Use 2 decimal places.)2.) For the sign test, rank-sum test, and Spearman correlation coefficient test, find the P-value of the sample test statistic. For the runs test of randomness, find the critical values from Table 10 of Appendix II. (Use 4 decimal places.)
The article "Simulation of the Hot Carbonate Process for Removal of CO, and H,S from
Medium Btu Gas" (K. Park and T. Edgar, Energy Progress, 1984:174–180) presents an
equation used to estimate the equilibrium vapor pressure of CO, in a potassium carbonate
solution. The actual equilibrium pressure (in kPa) was measured in nine different reactions
and compared with the value estimated from the equation. The results are presented in the
following table:
Reaction
Estimated Experimental
Difference
45.10
42.95
2.15
2
85.77
79.98
5.79
3
151.84
146.17
5.67
4.
244.30
228.22
16.08
5
257.67
240.63
17.04
6
44.32
41.99
2.33
84.41
82.05
2.36
8
150.47
149.62
0.85
253.81
245.45
8.36
Find a 95% confidence interval for the mean difference between the estimated and actual
pressures.
Air pollutants common in U.S. cities include fine particulate matter (PM) and ozone (O3). PM is measured as “inhalable” particles 10 micrometers in diameter or “fine inhalable” particles 2.5 micrometers in diameter. Suppose that studies show, for a particular region, that cities exceed PM2.5 standards 20% of the time and exceed ozone standards 10% of the time. Assume that PM2.5 and ozone measurements are statistically independent.
A) Determine the probability that a city, selected at random, exceeds one of the standards.
B) If a city exceeds the standards, what is the probability that it exceeds only the PM2.5 standard?
Chapter 6 Solutions
Statistics for Engineers and Scientists
Ch. 6.1 - In an experiment to measure the lifetimes of parts...Ch. 6.1 - A simple random sample consists of 65 lengths of...Ch. 6.1 - The article Supply Voltage Quality in Low-Voltage...Ch. 6.1 - The pH of an acid solution used to etch aluminum...Ch. 6.1 - Recently many companies have been experimenting...Ch. 6.1 - A certain type of stainless steel powder is...Ch. 6.1 - When it is operating properly, a chemical plant...Ch. 6.1 - Lasers can provide highly accurate measurements of...Ch. 6.1 - The article Predicting Profit Performance for...Ch. 6.1 - A new concrete mix is being designed to provide...
Ch. 6.1 - Fill in the blank: If the null hypothesis is H0: ...Ch. 6.1 - Fill in the blank: In a test of H0: 10 versus...Ch. 6.1 - An engineer takes a large number of independent...Ch. 6.1 - The following MINITAB output presents the results...Ch. 6.1 - The following MINITAB output presents the results...Ch. 6.2 - For which P-value is the null hypothesis more...Ch. 6.2 - Prob. 2ECh. 6.2 - If P = 0.01, which is the best conclusion? i. H0...Ch. 6.2 - If P = 0.50, which is the best conclusion? i. H0...Ch. 6.2 - True or false: If P = 0.02, then a. The result is...Ch. 6.2 - George performed a hypothesis test. Luis checked...Ch. 6.2 - The article The Effect of Restricting Opening...Ch. 6.2 - Let be the radiation level to which a radiation...Ch. 6.2 - In each of the following situations, state the...Ch. 6.2 - The installation of a radon abatement device is...Ch. 6.2 - It is desired to check the calibration of a scale...Ch. 6.2 - A machine that fills cereal boxes is supposed to...Ch. 6.2 - A method of applying zinc plating to steel is...Ch. 6.2 - Fill in the blank: A 95% confidence interval for...Ch. 6.2 - Refer to Exercise 14. For which null hypothesis...Ch. 6.2 - A scientist computes a 90% confidence interval to...Ch. 6.2 - The strength of a certain type of rubber is tested...Ch. 6.2 - A shipment of fibers is not acceptable if the mean...Ch. 6.2 - Refer to Exercise 17. It is discovered that the...Ch. 6.2 - Refer to Exercise 18. It is discovered that the...Ch. 6.2 - The following MINITAB output (first shown in...Ch. 6.3 - Integrated circuits consist of electric channels...Ch. 6.3 - The article HIV-positive Smokers Considering...Ch. 6.3 - Do bathroom scales tend to underestimate a persons...Ch. 6.3 - The article Evaluation of Criteria for Setting...Ch. 6.3 - In a survey of 500 residents in a certain town,...Ch. 6.3 - Prob. 6ECh. 6.3 - In a sample of 150 households in a certain city,...Ch. 6.3 - Prob. 8ECh. 6.3 - Let A and B represent two variants (alleles) of...Ch. 6.3 - Prob. 10ECh. 6.3 - Refer to Exercise 2 in Section 5.2. Can it be...Ch. 6.3 - The following MINITAB output presents the results...Ch. 6.3 - Prob. 13ECh. 6.4 - Each of the following hypothetical data sets...Ch. 6.4 - A geologist is making repeated measurements (in...Ch. 6.4 - A new centrifugal pump is being considered for an...Ch. 6.4 - A certain manufactured product is supposed to...Ch. 6.4 - The article Influence of Penetration Rate on...Ch. 6.4 - A new process for producing a type of novolac...Ch. 6.4 - Specifications call for the wall thickness of...Ch. 6.4 - As part of the quality-control program for a...Ch. 6.4 - The article Approximate Methods for Estimating...Ch. 6.4 - Refer to Exercise 12 in Section 5.3. Can you...Ch. 6.4 - Refer to Exercise 13 in Section 5.3. Can you...Ch. 6.4 - The following MINITAB output presents the results...Ch. 6.4 - The following MINITAB output presents the results...Ch. 6.5 - The article Capillary Leak Syndrome in Children...Ch. 6.5 - The article Some Parameters of the Population...Ch. 6.5 - The article Measurement of Complex Permittivity of...Ch. 6.5 - The article Wired: Energy Drinks, Jock Identity,...Ch. 6.5 - In a test to compare the effectiveness of two...Ch. 6.5 - Prob. 6ECh. 6.5 - A statistics instructor who teaches a lecture...Ch. 6.5 - Fifty specimens of a new computer chip were tested...Ch. 6.5 - Are low-fat diets or low-carb diets more effective...Ch. 6.5 - In a certain supermarket, a sample of 60 customers...Ch. 6.5 - The National Opinion Research Center polled a...Ch. 6.5 - Prob. 12ECh. 6.5 - Prob. 13ECh. 6.6 - Two extrusion machines that manufacture steel rods...Ch. 6.6 - Resistors labeled as 100 are purchased from two...Ch. 6.6 - The article A Music Key Detection Method Based on...Ch. 6.6 - Prob. 4ECh. 6.6 - The article HIV-positive Smokers Considering...Ch. 6.6 - Prob. 6ECh. 6.6 - To test the effectiveness of protective packaging,...Ch. 6.6 - Prob. 8ECh. 6.6 - The article Factors Associated with Exercise...Ch. 6.6 - Prob. 10ECh. 6.6 - Prob. 11ECh. 6.6 - In a study conducted by the U.S. Department of...Ch. 6.6 - Prob. 13ECh. 6.6 - Prob. 14ECh. 6.6 - Prob. 15ECh. 6.7 - A crayon manufacturer is comparing the effects of...Ch. 6.7 - In a study of the relationship of the shape of a...Ch. 6.7 - The article Influence of Penetration Rate on...Ch. 6.7 - The article Time Series Analysis for Construction...Ch. 6.7 - The Mastic tree (Pistacia lentiscus) is used in...Ch. 6.7 - Two weights, each labeled as weighing 100 g, are...Ch. 6.7 - It is thought that a new process for producing a...Ch. 6.7 - The article Effects of Aerosol Species on...Ch. 6.7 - The article Wind-Uplift Capacity of Residential...Ch. 6.7 - The article Magma Interaction Processes Inferred...Ch. 6.7 - The article Structural Performance of Rounded...Ch. 6.7 - The article Variance Reduction Techniques:...Ch. 6.7 - In an experiment to test the effectiveness of a...Ch. 6.7 - Prob. 14ECh. 6.7 - Prob. 15ECh. 6.7 - Prob. 16ECh. 6.7 - The following MINITAB output presents the results...Ch. 6.8 - The article Improved Bioequivalence Assessment of...Ch. 6.8 - The article Estimation of Mean Arterial Pressure...Ch. 6.8 - Prob. 3ECh. 6.8 - Prob. 4ECh. 6.8 - Prob. 5ECh. 6.8 - Prob. 6ECh. 6.8 - Prob. 7ECh. 6.8 - The article Effect of Granular Subbase Thickness...Ch. 6.8 - A crossover trial is a type of experiment used to...Ch. 6.8 - Prob. 10ECh. 6.8 - Prob. 11ECh. 6.8 - Prob. 12ECh. 6.8 - Prob. 13ECh. 6.9 - The article Wastewater Treatment Sludge as a Raw...Ch. 6.9 - Prob. 2ECh. 6.9 - The article Reaction Modeling and Optimization...Ch. 6.9 - Prob. 4ECh. 6.9 - Prob. 5ECh. 6.9 - Prob. 6ECh. 6.9 - A new postsurgical treatment is being compared...Ch. 6.9 - Prob. 8ECh. 6.9 - In a comparison of the effectiveness of distance...Ch. 6.9 - Prob. 10ECh. 6.10 - Fasteners are manufactured for an application...Ch. 6.10 - At an assembly plant for light trucks, routine...Ch. 6.10 - Prob. 3ECh. 6.10 - Prob. 4ECh. 6.10 - The article Chronic Beryllium Disease and...Ch. 6.10 - The article The Effectiveness of Child Restraint...Ch. 6.10 - For the given table of observed values,...Ch. 6.10 - For the given table of observed values, a....Ch. 6.10 - Fill in the blank: For observed and expected...Ch. 6.10 - Because of printer failure, none of the observed...Ch. 6.10 - Plates are evaluated according to their surface...Ch. 6.10 - The article Determination of Carboxyhemoglobin...Ch. 6.10 - Prob. 13ECh. 6.10 - Prob. 14ECh. 6.11 - A random sample of size 11 from a normal...Ch. 6.11 - A random sample of size 29 from a normal...Ch. 6.11 - Scores on an IQ test are normally distributed. A...Ch. 6.11 - A machine that fills beverage cans is supposed to...Ch. 6.11 - A sample of 25 one-year-old girls had a mean...Ch. 6.11 - Prob. 6ECh. 6.11 - Scores on the math SAT are normally distributed. A...Ch. 6.11 - One of the ways in which doctors try to determine...Ch. 6.11 - Prob. 9ECh. 6.11 - Find the upper 1% point of F2,5.Ch. 6.11 - Prob. 11ECh. 6.11 - A broth used to manufacture a pharmaceutical...Ch. 6.11 - Refer to Exercise 11 in Section 5.6. Can you...Ch. 6.11 - Prob. 14ECh. 6.12 - A hypothesis test is performed, and the P-value is...Ch. 6.12 - A process for a certain type of ore is designed to...Ch. 6.12 - A new braking system is being evaluated for a...Ch. 6.12 - A test is made of the hypotheses H0: 10 versus...Ch. 6.12 - A vendor claims that no more than 10% of the parts...Ch. 6.12 - Prob. 6ECh. 6.12 - A new process is being considered for the...Ch. 6.13 - A test has power 0.90 when = 15. True or false:...Ch. 6.13 - A test has power 0.80 when = 3.5. True or false:...Ch. 6.13 - If the sample size remains the same, and the level...Ch. 6.13 - If the level remains the same, and the sample...Ch. 6.13 - A tire company claims that the lifetimes of its...Ch. 6.13 - A copper smelting process is supposed to reduce...Ch. 6.13 - Prob. 7ECh. 6.13 - A new process for producing silicon wafers for...Ch. 6.13 - Prob. 9ECh. 6.13 - Prob. 10ECh. 6.13 - Prob. 11ECh. 6.14 - An agricultural scientist tests six types of...Ch. 6.14 - Prob. 2ECh. 6.14 - Six different settings are tried on a machine to...Ch. 6.14 - Prob. 4ECh. 6.14 - Twenty formulations of a coating are being tested...Ch. 6.14 - Prob. 6ECh. 6.14 - Each day for 200 days, a quality engineer samples...Ch. 6 - Exercises 1 to 4 describe experiments that require...Ch. 6 - Exercises 1 to 4 describe experiments that require...Ch. 6 - Exercises 1 to 4 describe experiments that require...Ch. 6 - Exercises 1 to 4 describe experiments that require...Ch. 6 - Suppose you have purchased a filling machine for...Ch. 6 - Prob. 6SECh. 6 - Prob. 7SECh. 6 - Twenty-one independent measurements were taken of...Ch. 6 - There is concern that increased industrialization...Ch. 6 - Prob. 10SECh. 6 - A machine that grinds valves is set to produce...Ch. 6 - Resistors for use in a certain application are...Ch. 6 - A machine manufactures bolts that are supposed to...Ch. 6 - Electric motors are assembled on four different...Ch. 6 - Refer to Exercise 14. The process engineer notices...Ch. 6 - Consider the following two samples:...Ch. 6 - Prob. 17SECh. 6 - Prob. 18SECh. 6 - Two different chemical formulations of rocket fuel...Ch. 6 - Prob. 20SECh. 6 - Prob. 21SECh. 6 - The article Valuing Watershed Quality Improvements...Ch. 6 - Anthropologists can estimate the birthrate of an...Ch. 6 - Prob. 24SE
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, statistics and related others by exploring similar questions and additional content below.Similar questions
- If µ1 =population mean number of effective hours for standard wax and u2 = population mean number of effective hours for the new wax, then the manufacturer's alternative hypothesis is: %3D a. b. none of these - H2 =0 C u1 H1 - H2 >0 µ2 >0 Od.u1 - µ2 # 0 Oe u1 - #2 <0 %3D %3Darrow_forwardChlorophylls a and b are plant pigments that absorb sunlight and transfer the energy into photosynthesis of carbohydrates from CO2 and H2O, releasing O2 in the process. Chlorophylls were extracted from chopped up grass and measured by spectrophotometry. The table shows results for chlorophyll a for four separate analysis of five blades of grass. Chlorophyll a (g/L) Blade 1 Blade 2 Blade 3 Blade 4 Blade 5 1.09 1.26 1.1 1.23 0.85 0.86 0.96 1.21 1.3 0.65 0.93 0.8 1.27 0.97 0.86 0.99 0.73 1.12 0.97 1.03 Four replicate measurements for each blade of grass tell us the precision of the analytical procedure (sanalysis). Differences between mean values for each of the five blades of grass are a measure of variation due to sampling (ssampling). Using Excel and it’s ANOVA function, find the standard deviations attributable to sampling and to analysis, as well as the overall standard deviation arising from both sources.arrow_forwardQ1. Consider the following cross-sectional population regression model relating the dependent variable Y, and regressor X, : Y, = Bo + BIXI + u, where i = 1,..,n, and X, = Y, + Z.. Assume that Cov(Z,u) 0. (a) Explain why X, is an endogenous regressor. (b) Show that Z, is a relevant instrument for X;. %3Darrow_forward
- The article “The Selection of Yeast Strains for the Production of Premium Quality South African Brandy Base Products ” (C. Steger and M. Lambrechts, Journal of Industrial Microbiology and Biotechnology, 2000:431– 440) presents detailed information on the volatile compound composition of base wines made from each of 16 selected yeast strains. Following are the concentrations of total esters (in mg/L) in each of the wines. 105.14 139.38 144.39 170.41 172.79 173.01 188.72 197.81 215.34 229.55 256.02 284.34 295.24 303.28 312.95 658.38 the 10th , 60th and 90th percentiles are given by (in that order); Select one: a. 122.25 , 222.44, 308.11 b. 139.38, 215.34, 312.95 c. 122.26, 242.79, 485.67 d. 141.88, 242.78, 485.66 e. 122.26 , 242.79, 312.95arrow_forward17.7 Butterfly wings. Researchers studied the morphological attributes of monarch butterflies (Danaus plexippus), a species that undertakes large seasonal migrations over North America. They measured the forewing weight (in milligrams, mg) of a sample of 92 monarch butterflies, all of which had been reared in captivity in identical conditions.° Figure 17.4 shows the output from the statistical software JMP. (The data are also available in the Large.Butterfly the data file if you wish to practice working with your own software.) Estimate with 95% confidence the mean forewing weight of monarch butterflies reared in captivity. Follow the four- step process as illustrated in Example 17.2. 4 STEP そMP FWweight 30 25 20 15 10 11 12 13 14 15 8 9 10 Summary Statistics Mean 11.795652 Std Dev 1.1759413 Std Err Mean 0.1226004 Upper 95% Mean Lower 95% Mean 1 FIGURE 17.4 Software output (JMP) for the forewing weight of monarch 12.039183 11.552122 92 N. butterflies. Countarrow_forwardThe article "Enthalpies and Entropies of Transfer of Electrolytes and Ions from Water to Mixed Aqueous Organic Solvents" (G. Hefter, Y. Marcus, and W. Waghome, Chemical Reviews, 2002-2773-2836) presents measurements of entropy and enthalpy changes for many salts under a variety of conditions. The following table presents the results for enthalpy of transfer (in kJ/mol) from water to water + methanol of NaCi (table salt) for several concentrations of methanol. Four independent measurements were made at each concentration. Concentration (%) Enthalpy 1.62 1.60 1.62 1.66 10 3.56 3.35 2.69 2.66 2.72 2.73 20 3.45 3.65 3.52 30 3.18 3.40 3.06 a Is it plausible that the enthalpy is the same at all concentrations? Explain. b. Which pairs of concentrations, if any, can you conclude to have differing enthalpies?arrow_forward
- The article "The Selection of Yeast Strains for the Production of Premium Quality South African Brandy Base Products" (C. Steger and M. Lambrechts, Journal of Industrial Microbiology and Biotechnology, 2000:431-440) presents detailed information on the volatile compound composition of base wines made from each of 16 selected yeast strains. Following are the concentrations of total esters (in mg/L) in each of the wines. 284.34 173.01 229.55 312.95 215.34 188.72 144.39 172.79 139.38 197.81 303.28 256.02 658.38 105.14 295.24 170.41 Compute the mean concentration. a. b. Compute the median concentration. Compute the first quartile of the concentrations. C. d. Compute the third quartile of the concentrations. Construct a boxplot for the concentrations. What features does it reveal? e.arrow_forwardThe article "Enthalpies and Entropies of Transfer of Electrolytes and Ions from Water to Mixed Aqueous Organic Solvents" (G. Hefter, Y. Marcus, and W. Waghorne, Chemical Reviews, 2002:2773–2836) presents measurements of entropy and enthalpy changes for many salts under a variety of conditions. The following table presents the results for entropies of transfer (in J/K · mol) from water to water + methanol of NaCl (table salt) over a range of concentrations of methanol: Concentration (%) Entropy 5 10 -1 20 -7 30 -17 40 -28 50 -39 60 -52 70 -65 80 -80 90 -98 100 -121 Fit polynomial models of degrees 1, 2, and 3 to predict the entropy (y) from the concentration (x). a. b. Which degree polynomial is the most appropriate? Explain. Using the most appropriate model, find 99% confidence intervals for the coefficients. C.arrow_forwardA manufacturer of automobile products has developed a new wax and is interested in comparing the new wax with their standard wax to determine if the new wax will protect a car for a longer period of time. In order to make a comparison, both waxes are applied to five new cars respectively and exposed to the same environmental conditions. The results of the test are:arrow_forward
- Fluoride Exposure in Drinking WaterExercise 2.250 introduces a study showing thatfluoride exposure might have long-term negativeconsequences for the offspring of pregnant women.Part of the study examines the effect of adding flu-oride to tap water on mean fluoride concentrationin women. Summary statistics for fluoride concen-tration (measured in mg/L) for the two groups are given in Table 6.17. Find and interpret a 99% con-fidence interval for the mean increase in fluorideconcentration for those with fluoridated tap water. 1. find the t-score enter positive z-score 2. find the standard of error round 4 decimal places. 3 find the margin of error round 4 decimal placesarrow_forwardThe article "Oxidation State and Activities of Chromium Oxides in Cao-SiO,-CrO, Slag System" (Y. Xiao, L. Holappa, and M. Reuter, Metallurgical and Materials Transactions B, 2002:595-603) presents the amount x (in mole percent) and activity coefficient y of CrO,5 for several specimens. The data, extracted from a larger table, are presented in the following table. х У 2.6 10.20 5.03 19.9 8.84 0.8 6.62 5.3 2.89 20.3 2.31 39.4 7.13 5.8 3.40 29.4 5.57 2.2 7.23 5.5 2.12 33.1 1.67 44.2 5.33 13.1 16.70 0.6 9.75 2.2 2.74 16.9 2.58 35.5 1.50 48.0 Compute the least-squares line for predicting y from x. b. Plot the residuals versus the fitted values. Compute the least-squares line for predicting y from 1/x. d. Plot the residuals versus the fitted values. C. Using the better fitting line, find a 95% confidence interval for the mean value of y when x= 5.0.arrow_forwardThe article "Measurements of the Thermal Conductivity and Thermal Diffusivity of Polymer Melts with the Short-Hot-Wire Method" (X. Zhang, W. Hendro, et al., International Journal of Thermophysics, 2002:1077-1090) reports measurements of the thermal conductivity (in W· m-1 . K') and diffusivity of several polymers at several temperatures (in 1000°C). The following table presents results for the thermal conductivity of polycarbonate. Cond. Temp. 0.236 0.028 0.241 0.038 0.244 0.061 0.251 0.083 0.259 0.107 0.257 0.119 0.257 0.130 0.261 0.146 0.254 0.159 0.256 0.169 0.251 0.181 0.249 0.204 0.249 0.215 0.230 0.225 0.230 0.237 0.228 0.248 Denoting conductivity by y and temperature by x, fit the linear model y = Bo + Bix + ɛ. a. For each coefficient, test the hypothesis that the coefficient is equal to 0. b. Fit the quadratic model y = Bo + Bix + Bzx? + ɛ. For each coefficient, test the Page 661 Fit the cubic model y = Bo + Bix + Bx + Bax + ɛ. For each coefficient, test the %3D hypothesis that…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons IncProbability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage LearningStatistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
- Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSONThe Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. FreemanIntroduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman
MATLAB: An Introduction with Applications
Statistics
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...
Statistics
ISBN:9781305251809
Author:Jay L. Devore
Publisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...
Statistics
ISBN:9781305504912
Author:Frederick J Gravetter, Larry B. Wallnau
Publisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...
Statistics
ISBN:9780134683416
Author:Ron Larson, Betsy Farber
Publisher:PEARSON
The Basic Practice of Statistics
Statistics
ISBN:9781319042578
Author:David S. Moore, William I. Notz, Michael A. Fligner
Publisher:W. H. Freeman
Introduction to the Practice of Statistics
Statistics
ISBN:9781319013387
Author:David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:W. H. Freeman
Hypothesis Testing using Confidence Interval Approach; Author: BUM2413 Applied Statistics UMP;https://www.youtube.com/watch?v=Hq1l3e9pLyY;License: Standard YouTube License, CC-BY
Hypothesis Testing - Difference of Two Means - Student's -Distribution & Normal Distribution; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=UcZwyzwWU7o;License: Standard Youtube License