Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 31P
In a pipe 0.3 m in diameter, 0.3 m3/s of water are pumped up a hill. On the hilltop (elevation 48), the line reduces to 0.2 m diameter. If the pump maintains a pressure of 690 kPa at elevation 21, calculate the pressure in the pipe on the hilltop.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A water pump has an outlet diameter of 70 mm horizontal pipe flowing full at the outlet. The resulting jet strikes the ground surface at a horizontal distance of 32 m and a vertical distance of 1.75 m from the outlet. Find the pumping capacity in liters per minute.
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
Chapter 6 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 6 - An incompressible frictionless flow field is given...Ch. 6 - A velocity field in a fluid with density of 1000...Ch. 6 - The x component of velocity in an incompressible...Ch. 6 - Consider the flow field with the velocity given by...Ch. 6 - Consider the flow field with the velocity given by...Ch. 6 - The velocity field for a plane source located...Ch. 6 - In a two-dimensional frictionless, incompressible...Ch. 6 - Consider a two-dimensional incompressible flow...Ch. 6 - An incompressible liquid with a density of 900...Ch. 6 - Consider a flow of water in pipe. What is the...
Ch. 6 - The velocity field for a plane vortex sink is...Ch. 6 - An incompressible liquid with negligible viscosity...Ch. 6 - Consider water flowing in a circular section of a...Ch. 6 - Consider a tornado as air moving in a circular...Ch. 6 - A nozzle for an incompressible, inviscid fluid of...Ch. 6 - A diffuser for an incompressible, inviscid fluid...Ch. 6 - A liquid layer separates two plane surfaces as...Ch. 6 - Consider Problem 6.15 with the nozzle directed...Ch. 6 - Consider Problem 6.16 with the diffuser directed...Ch. 6 - A rectangular computer chip floats on a thin layer...Ch. 6 - Heavy weights can be moved with relative ease on...Ch. 6 - The y component of velocity in a two-dimensional...Ch. 6 - The velocity field for a plane doublet is given in...Ch. 6 - Tomodel the velocity distribution in the curved...Ch. 6 - Repeat Example 6.1, but with the somewhat more...Ch. 6 - Using the analyses of Example 6.1 and Problem...Ch. 6 - Water flows at a speed of 25 ft/s. Calculate the...Ch. 6 - Plot the speed of air versus the dynamic pressure...Ch. 6 - Water flows in a pipeline. At a point in the line...Ch. 6 - In a pipe 0.3 m in diameter, 0.3 m3/s of water are...Ch. 6 - A jet of air from a nozzle is blown at right...Ch. 6 - The inlet contraction and test section of a...Ch. 6 - Maintenance work on high-pressure hydraulic...Ch. 6 - An open-circuit wind tunnel draws in air from the...Ch. 6 - Water is flowing. Calculate H(m) and p(kPa). P6.36Ch. 6 - If each gauge shows the same reading for a flow...Ch. 6 - Derive a relation between A1 and A2 so that for a...Ch. 6 - Water flows steadily up the vertical 1...Ch. 6 - Your car runs out of gas unexpectedly and you...Ch. 6 - A tank at a pressure of 50 kPa gage gets a pinhole...Ch. 6 - The water flow rate through the siphon is 5 L/s,...Ch. 6 - Water flows from a very large tank through a 5 cm...Ch. 6 - Consider frictionless, incompressible flow of air...Ch. 6 - A closed tank contains water with air above it....Ch. 6 - Water jets upward through a 3-in.-diameter nozzle...Ch. 6 - Calculate the rate of flow through this pipeline...Ch. 6 - A mercury barometer is carried in a car on a day...Ch. 6 - A racing car travels at 235 mph along a...Ch. 6 - The velocity field for a plane source at a...Ch. 6 - A smoothly contoured nozzle, with outlet diameter...Ch. 6 - Water flows steadily through a 3.25-in.-diameter...Ch. 6 - A flow nozzle is a device for measuring the flow...Ch. 6 - The head of water on a 50 mm diameter smooth...Ch. 6 - Water flows from one reservoir in a 200-mm pipe,...Ch. 6 - Barometric pressure is 14.0 psia. What is the...Ch. 6 - A spray system is shown in the diagram. Water is...Ch. 6 - Water flows out of a kitchen faucet of...Ch. 6 - A horizontal axisymmetric jet of air with...Ch. 6 - The water level in a large tank is maintained at...Ch. 6 - Many recreation facilities use inflatable bubble...Ch. 6 - Water flows at low speed through a circular tube...Ch. 6 - Describe the pressure distribution on the exterior...Ch. 6 - An aspirator provides suction by using a stream of...Ch. 6 - Carefully sketch the energy grade lines (EGL) and...Ch. 6 - Carefully sketch the energy grade lines (EGL) and...Ch. 6 - Water is being pumped from the lower reservoir...Ch. 6 - The turbine extracts power from the water flowing...Ch. 6 - Consider a two-dimensional fluid flow: u = ax + by...Ch. 6 - The velocity field for a two-dimensional flow is...Ch. 6 - A flow field is characterized by the stream...Ch. 6 - The flow field for a plane source at a distance h...Ch. 6 - The stream function of a flow field is = Ax2y ...Ch. 6 - A flow field is characterized by the stream...Ch. 6 - A flow field is characterized by the stream...Ch. 6 - The stream function of a flow field is = Ax3 ...Ch. 6 - A flow field is represented by the stream function...Ch. 6 - Consider the flow field represented by the...Ch. 6 - Show by expanding and collecting real and...Ch. 6 - Consider the flow field represented by the...Ch. 6 - An incompressible flow field is characterized by...Ch. 6 - Consider an air flow over a flat wall with an...Ch. 6 - A source with a strength of q = 3 m2/s and a sink...Ch. 6 - The velocity distribution in a two-dimensional,...Ch. 6 - Consider the flow past a circular cylinder, of...Ch. 6 - The flow in a corner with an angle can be...Ch. 6 - Consider the two-dimensional flow against a flat...Ch. 6 - A source and a sink with strengths of equal...Ch. 6 - A flow field is formed by combining a uniform flow...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
9.28 A column is supported by a base plate, pedestal, and footing, as shown. The load applied on the column is ...
Applied Statics and Strength of Materials (6th Edition)
4. You are experimenting with several liquid metal alloys to find a suitable replacement for the mercury used i...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
The quantity ms into s.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 100 mm diameter suction pipe leading to a pump carries a discharge of 0.03m3/s of oil (0.85), if the pressure at point A in the suction pipe is a vacuum of 180mmHg, find the total energy head at point A with respect to the datum of the pumparrow_forward2. Oil (sg=0.90) is flowing at 150 L/min through a turbine. The pressure before the turbine is 750 kPa and after the turbine 150 kPa with an elevation between these two points of 2.3 m [ fluid entrance is on the high side ]. If the friction loss in the system is 5.10 N.m/N find (a) the power delivered to the turbine by the fluid and (b) If the mechanical efficiency of the turbine is 80 % find the power output from the turbine.arrow_forwardA nozzle that discharges a 60-mm-diameter water jet into the air is on the right end of a horizontal 120-mm- diameter pipe. In the line, the water has a velocity of 4 m/s and a gage pressure of 400 kPa. Find the magnitude and direction of the resultant axial force the water exerts on the nozzle and the head loss in the nozzle.arrow_forward
- A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the output power of the pump, in hp? Round off to two decimal places.arrow_forwardThe task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT. The pictures I will post is the guide to answer Its okay if the answer is computerizedarrow_forwardThe task is to to transfer the fluid from the source towards the tank (TANK A) lying on an elevated platform as shown. The goal is to fill up that 16.49 m by 2.23 m by 6.36 m tank (TANK A) within 11.5 mins (from empty to full). Your budget is limited to 605,000 pesos. Head loss on pipe due to friction is 1.23 meters per 1 meter of pipe. Because it's Fluid Machinery and not Engineering Economics, it's ok for your design to exceed the budget BUT YOU HAVE TO JUSTIFY IT.arrow_forward
- In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa at the first point. Find the gauge pressure at a second point in the line if the cross-sectional area at the second point is thrice that at the first.arrow_forwardWater flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter of 75 mm and then stays at that diameter. The flow speed in the 35 mm pipe is 32 m/s. The water gage pressure in the thinner pipe is 510 kPa. 1. What is the pressure at the entrance to the thicker section of the pipe? Is the pressure there larger or smaller than in the thin pipe section? 2. What force is acting on the coupling? Is it tension or compression?arrow_forwardIf the velocity of water is 8m/s and the pressure is 140 kPa on the discharge side of a pump, What will be the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? How much power is required to drive it if the diameter of suction side is 600 mm? If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system?arrow_forward
- A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the input power of the pump, in hp? Round off to two decimal places.arrow_forwardThe reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40arrow_forwardA pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. include your free body diagram A.12.74 m B.-4.67 m C.-2.72 m D.2.56arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license