Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 5.11.4P
To determine
(a)
The W shape.
To determine
(b)
The W shape.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Details of a rectangular column are as follows:
Column width along X-axis-250 mm
Column Depth along the Y-axis-600 mm
8-25 mm diameter bars distributed equally along the longer sides.
10 mm diameter ties spaced at 10 mm on centers
Concrete 28th day Compressive strength, fc;=20.7 MPa
Reinforcing Steel yield strength, fy-415 MPa
Assume that compression steel yields.
a) Which of the following gives the nominal balanced load Pb (kN). A = 90.4 mm
b) Which of the following gives the nominal axial load (kN) that the column n carry at an
eccentricity of 200 mm along the X axis from the centroidal Y-axis.
Design an interior span slab of a concrete floor system with the following description:
Span = 30 m Imposed dead load= 900 N/m2 Live load= 4900 N/m2 fc’= 28 MPa fy = 415 MPa
Note :- Solve by ACI method
A reinforced concrete cantilever beam is shown
below. The beam cross section is a rectangle,
12 inches deep by 18 inches wide.
Material properties are:
- Concrete weight: wt = 150 pcf
- Concrete compressive strength: f'c = 4000 psi
- Concrete tensile strength: f't= 400 psi
- Steel tensile strength: fy = 60 ksi
- Stirrup consists of #4 bar
- Beam is not exposed to weather or in contact
with soil.
Calculate the maximum bending moment under the beam self-weight.
10 ft-
8,750 lb-ft
10,250 lb-ft
11,250 lb-ft
11,750 lb-ft
18"
BEAM SECTION
Chapter 5 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 5 - Prob. 5.2.1PCh. 5 - Prob. 5.2.2PCh. 5 - Verify the value of Zx for a W1850 that is...Ch. 5 - Prob. 5.2.4PCh. 5 - Prob. 5.4.1PCh. 5 - Prob. 5.4.2PCh. 5 - Determine the smallest value of yield stress Fy,...Ch. 5 - Prob. 5.5.1PCh. 5 - Prob. 5.5.2PCh. 5 - Prob. 5.5.3P
Ch. 5 - Prob. 5.5.4PCh. 5 - Prob. 5.5.5PCh. 5 - Prob. 5.5.6PCh. 5 - Prob. 5.5.7PCh. 5 - Prob. 5.5.8PCh. 5 - Prob. 5.5.9PCh. 5 - If the beam in Problem 5.5-9 i5 braced at A, B,...Ch. 5 - Prob. 5.5.11PCh. 5 - Prob. 5.5.12PCh. 5 - Prob. 5.5.13PCh. 5 - Prob. 5.5.14PCh. 5 - Prob. 5.5.15PCh. 5 - Prob. 5.5.16PCh. 5 - Prob. 5.6.1PCh. 5 - Prob. 5.6.2PCh. 5 - Prob. 5.6.3PCh. 5 - Prob. 5.6.4PCh. 5 - Compute the nominal shear strength of an M107.5 of...Ch. 5 - Compute the nominal shear strength of an M1211.8...Ch. 5 - Prob. 5.8.3PCh. 5 - Prob. 5.8.4PCh. 5 - Prob. 5.10.1PCh. 5 - Prob. 5.10.2PCh. 5 - Same as Problem 5.10-2, except that lateral...Ch. 5 - Prob. 5.10.4PCh. 5 - The given beam is laterally supported at the ends...Ch. 5 - Prob. 5.10.6PCh. 5 - Prob. 5.10.7PCh. 5 - Prob. 5.11.1PCh. 5 - Prob. 5.11.2PCh. 5 - Prob. 5.11.3PCh. 5 - Prob. 5.11.4PCh. 5 - Prob. 5.11.5PCh. 5 - Prob. 5.11.6PCh. 5 - Prob. 5.11.7PCh. 5 - Prob. 5.11.8PCh. 5 - Prob. 5.11.9PCh. 5 - Prob. 5.12.1PCh. 5 - Prob. 5.12.2PCh. 5 - Prob. 5.12.3PCh. 5 - Prob. 5.13.1PCh. 5 - Prob. 5.13.2PCh. 5 - Prob. 5.14.1PCh. 5 - Prob. 5.14.2PCh. 5 - Prob. 5.14.3PCh. 5 - Prob. 5.14.4PCh. 5 - Prob. 5.15.1PCh. 5 - Prob. 5.15.2PCh. 5 - Prob. 5.15.3PCh. 5 - Prob. 5.15.4PCh. 5 - Prob. 5.15.5PCh. 5 - Prob. 5.15.6PCh. 5 - Prob. 5.15.7PCh. 5 - Same as Problem 5.15-7, except that the sag rods...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculatearrow_forwardA beam has a width of 300 mm and an effective depth of 480 mm strength Pc= 34 MPa. Steel yield strength fy=415 MPa. The section is to be reinforced for tension only and the effective concrete cover is 70 mm. Deadload moment is 140 kN-m and the liveload moment is 180 kN-m. Use 2010 NSCP with t= 0.005. A. What is the governing steel ratio? B. What is the maximum number of bars needed for a 25mm diameter reinforcements? C. What is the minimum number of bars needed for a 25mm diameter reinforcements?arrow_forwardUSE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90arrow_forward
- Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)arrow_forwardProblem 01 Using ASD, check the adequacy of the base plate (PL400X350×19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600KN and PLL = 320 kN. Use A-36 steel and concrete fc'=20 MPa. THarrow_forwardAW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w = 4.6 kips/ft, LAB = 3.4 ft, LBc = 3.4 ft, and LCD= 16.6 ft. Determine the magnitude of the maximum bending stress in the beam. A P Answer: Omax LAB = B Save for Later LBC eTextbook and Media C ksi W LCD D X Attempts: 0 of 3 used Submit Answerarrow_forward
- The W10 × 88 column shown bears on a concrete pedestal of the same size as the square column base plate. The column load is Pu = 600 kips (LRFD) or Pa = 400 kips (ASD). The compressive strength of the concrete is 5 ksi. Section properties A = 25.9 in TIH d = 10.8 in tw = 0.605 in bf = 10.3 in tf = 0.99 in bf/2tf = 5.18 h/tw = 13.0 n (A) 15 in x 15 in × 1 in (C) 16 in x 16 in × 1 in 0.80bf B n n 0.95d N n The smallest of the following base plates that meets the design criteria is (B) 15 in x 15 in x 1.25 in (D) 16 in x 16 in × 1.25 in Material properties W10 × 88 ASTM A992 Fy = 50 ksi Fu = 65 ksi plate ASTM A572, grade 50 Fy = 50 ksi Fu = 65 ksiarrow_forward1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1arrow_forwardThe rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=warrow_forward
- A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.arrow_forwardDesign Specifications 1st and 2nd floor Member Roof Deck Load (Typical) Live Load Item Superimposed Dead Load (Typical) Live Load Superimposed Dead a. b. C. For the structural plan attached, Hint: Self-weight B1 B2 Notes: 1. For simplicity, neglect self-weight of concrete slab B3 G1 G2 C1 C2 Design Loadings Application Slabs Slabs Slabs Slabs Value 4 3 2 3 4 4 4 Value 4 means pinned means continuous Assume all members have the same stiffness (same El) for simplicity 8 4 6 Unit kN/m kN/m kN/m kN/m kN/m kN/m kN/m Unit kPa kPa kPa kPa Determine the factored bending moment (LRFD) to be used in the design of Beam B1 in kNm. Determine the factored shear force (LRFD) to be used in the design of Girder G2 in kN. Determine the factored axial load (LRFD) to be used in the design of Column C1 in kN. -I T C2 G2 C1 G1 C1 5000 B3 1 B2 B1 B2 C2 C1 ∙H. GROUND FLOOR FRAMING PLAN C1 I G2 H G1 İ 8 C2 C1 G1 C1 5000 B3 1 B2 B1 + B2 1 B3 . C2 C1 I C1 SECOND FLOOR AND ROOF DECK FRAMING PLAN G1 G1arrow_forwardAW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 23 kips, w= 6.0 kips/ft, LaB = 5.8 ft, Lgc = 5.8 ft, and Lco = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. B Ic LAB I Lnc LCD Answer: Omax = ksiarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning