PRIN.OF HIGHWAY ENGINEERING&TRAFFIC ANA.
7th Edition
ISBN: 9781119610526
Author: Mannering
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Question
Chapter 3, Problem 34P
To determine
Thereconstructed length of existing level of highway which provides an appropriate vertical alignment.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A rural highway has a +6% grade on a mountainous region. If the maximum and minimum the speed limit on this highway for trucks is 70 mph and 45 mph, respectively, determining the “critical length” of this grade
b) The vertical alignments of two roads A and B are to be design with speeds
60km/hr and 80km/r, respectively. Differentiate between the two roads in
terms of the level of applicable design standards and the expected cost of
implementation.
A new basic freeway segment will have 3 lanes in each direction. The left and center lane each has a width of 12 ft while the width of the right lane is 13 ft. The left shoulder is 4 ft while the right shoulder is also 4 ft. There are 2 interchanges within 6 miles (3 miles upstream and 3 miles down stream).The site has level terrain, the design speed is 80 mph the hourly design volume is 5250 veh/h, which includes 9.0% trucks and buses. The peak hour factor is 0.870.
Calculate FHV, VP, FFS, LOS Show all work
Chapter 3 Solutions
PRIN.OF HIGHWAY ENGINEERING&TRAFFIC ANA.
Ch. 3 - Prob. 1PCh. 3 - Prob. 2PCh. 3 - Prob. 3PCh. 3 - Prob. 4PCh. 3 - Prob. 5PCh. 3 - Prob. 6PCh. 3 - Prob. 7PCh. 3 - Prob. 8PCh. 3 - Prob. 9PCh. 3 - Prob. 10P
Ch. 3 - Prob. 11PCh. 3 - Prob. 12PCh. 3 - Prob. 13PCh. 3 - Prob. 14PCh. 3 - Prob. 15PCh. 3 - Prob. 16PCh. 3 - Prob. 17PCh. 3 - Prob. 18PCh. 3 - Prob. 19PCh. 3 - Prob. 20PCh. 3 - Prob. 21PCh. 3 - Prob. 22PCh. 3 - Prob. 23PCh. 3 - Prob. 24PCh. 3 - Prob. 25PCh. 3 - Prob. 26PCh. 3 - Prob. 27PCh. 3 - Prob. 28PCh. 3 - Prob. 29PCh. 3 - Prob. 30PCh. 3 - Prob. 31PCh. 3 - Prob. 32PCh. 3 - Prob. 33PCh. 3 - Prob. 34PCh. 3 - Prob. 35PCh. 3 - Prob. 36PCh. 3 - Prob. 37PCh. 3 - Prob. 38PCh. 3 - Prob. 39PCh. 3 - Prob. 40PCh. 3 - Prob. 41PCh. 3 - Prob. 42PCh. 3 - Prob. 43PCh. 3 - Prob. 44PCh. 3 - Prob. 45PCh. 3 - Prob. 46PCh. 3 - Prob. 47PCh. 3 - Prob. 48PCh. 3 - Prob. 49PCh. 3 - Prob. 50PCh. 3 - Prob. 51PCh. 3 - Prob. 52PCh. 3 - Prob. 53PCh. 3 - Prob. 54PCh. 3 - Prob. 55PCh. 3 - Prob. 56PCh. 3 - Prob. 57PCh. 3 - Prob. 58PCh. 3 - Prob. 59PCh. 3 - Prob. 60PCh. 3 - Prob. 61PCh. 3 - Prob. 62PCh. 3 - Prob. 63PCh. 3 - Prob. 64PCh. 3 - Prob. 65PCh. 3 - Prob. 66PCh. 3 - Prob. 67P
Knowledge Booster
Similar questions
- A highway is being designed to AASHTO guidelines with a 70 mph (113 km/h) design speed and at one section an equal tangent vertical curve must be designed to connect grades of +1% and -2%. Then; Determine the minimum length of the curve necessary to meet SSD requirements.arrow_forward3. A rural highway has a +6% grade on a mountainous region. If the maximum and mini- mum speed limit on this highway for trucks is 55 mph and 45 mph, respectively, determine the "critical length" of this grade.arrow_forwardThe arterial road with a 100 km/h design speed will be constructed on the flat terrain. At one section, the equal tangent vertical curve as shown in Table 3 is proposed. Table 3: Parameters of Vertical Alignment Length 490 m PVC station 3+700.000 PVC elevation 460 m Initial grade -3.5% Final grade 6.5% (a) Calculate the stationing and elevation of the low point, PVI and PVT. (b) Calculate the minimum length of curve to meet stopping sight distance requirementsarrow_forward
- What super-elevation rate would you recommend for a roadway with a design speed of 110 kph and a radius of 1400 ft? Assume f=0.11.arrow_forwardA 3.25-mile segment of undivided, four-lane highway is primarily on level terrain. The highway segment does, however, contain one sustained grade of 2.5% that is 3,200 ft long. Other relevant information include: Base free-flow speed = 65 mph %3! 11-ft lanes • 4 ft clearance at the roadside (right side) • 20 access points/mile Peak-hour volume = 1,900 veh/h 13% trucks; 2% RVs • PHF = 0.90 • Familiar facility users At what LOS is the highway expected to operate? (Hint: Three different analyses will be needed: a) the level terrain portion of the highway, b) the 2.5% upgrade portion of the highway, and c) the 2.5% downgrade portion of the highway.)arrow_forwardAs SR361 enters Middletown from the NW, it must curve to the south between two historic buildings. At this point, SR361 consists of two 11-foot lane. The building to the right of traffic, is only 10 feet from the edge of the 5-foot wide shoulder. Local policy is that the superelevation rates not exceed 0.06 inches per inch. Will the minimum SSD be available from vehicles moving at 60 mph through this curve?arrow_forward
- A roadway has a design speed of 50 mi/h, and at station 105 + 00 a +3.0% grade roadway section ends and at station 125 + 00 a +2.0% grade roadway section begins. The +3.0% grade section of highway (at station 105 + 00) is at a higher elevation than the +2.0% grade section of highway (at station 125 + 00). If a -4%constant-grade section is used to connect the crest and sag vertical curves that are needed to link the +3.0 and+2.0% grade sections, what is the elevation difference between stations 105 + 00 and 125 + 00? (The entire alignment, crest and sag curves, and constant-grade section must fit between stations 105 + 00 and 125 +00.)arrow_forwardA roadway has a design speed of 50 mi/h, and at station 105 + 00 a +3.0% grade roadway ection ends and at station 125 + 00 a+2.0% grade roadway section begins. The +3.0% grade section of highway (at station 105 + 00) is at a higher elevation than the +2.0% grade section of highway (at station 125 + 00). If a -4%constant-grade section is used to connect the crest and sag vertical curves that are needed to link the +3.0 and+2.0% grade sections, what is the elevation difference between stations 105 + 00 and 125 + 00? (The entire alignment, crest and sag curves, and constant-grade section must fit between stations 105 + 00 and 125 +00.)arrow_forwardThe extra widening required for a two-lane national highway at a horizontal curve of 300 m radius, considering a wheel base of 8m and a design speed of 100kmph isarrow_forward
- It is defined as an at-grade crossing of two or more roadways. Choices: A. Intersection B. Block C. Street D. Highwayarrow_forwardIt is the minimum width of two-lane farm to market road having an average daily traffic of less than 200. O 6.70 m O 6.10 m O 5.0 m O 4.0 marrow_forwardA single-lane ramp is proposed to be designed on a section of the eastbound direction of a four-lane undivided conventional highway that is on a curve. The centerline alignment horizontal curve radius is 5000 feet. Prepare a preliminary design for the ramp, draft, and add callouts. Assume standard lane and shoulder widths. Clearly state other assumptions, if necessary. Please ensure to show all necessary curve radii and shoulder widths (including ramp shoulders).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning