EBK MANUFACTURING PROCESSES FOR ENGINEE
6th Edition
ISBN: 9780134425115
Author: Schmid
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem 2.100P
To determine
The depth of penetration in a Brinell hardness test.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A mild steel material is subjected to a Brinell
hardness test with an applied force of 7459
N using a hardened steel ball indentor of 11
mm and it is found that the Brinell Hardness
Number as 954. Determine the surface area
of indentation and indentation diameter.
(NOTE: Please Solve the problem in a
paper and upload in the separate
submission link provided and also fill
the answers without the unit in the box
below)
i) Surface Area of Indentation (in mm?)
-- (
ii) Indentation Diameter (in mm)
Tutorial Problem 3
The following data are obtained from the Charpy impact test of a copper specimen.
a) Length of the square cross-section specimen = 70 mm
b) Each side (top & bottom) of the cross-section = 9.64 mm
c) V – Notch thickness at middle of the specimen length = 1.06 mm
d) Impact Strength = 279 kJ/m²
Determine the Cross-sectional area at the top surface, Cross-sectional area at notch & Impact energy of the
copper specimen.
Problems
1. A Rockwell hardness measurement is made on a ductile iron (80-55-06 as cast) and the
obtained Rockwell hardness R scale is 13 HRC. Predict the tensile and yield strengths of this
material.
2. A Brinell hardness measurement is made on a ductile iron (120-90-02, Oil-quenched) using a
10-mm-diameter sphere of tungsten carbide. A load of 3,000 kg produces a 3.52-mm-
diameter impression in the iron surface.
a. Calculate the BHN of this alloy. (The correct units for the Brinell equation are
kilograms for load and millimeters for diameters.)
b. Predict the tensile and yield strengths
3. Suppose that a ductile iron (100-70-03, air-quenched) has a tensile strength of 800 MPa.
What diameter impression would you expect the 3,000-kg load to produce with the 10-mm-
diameter ball?
Search
LO
W
SE
Chapter 2 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
Ch. 2 - Prob. 2.1QCh. 2 - Prob. 2.2QCh. 2 - Prob. 2.3QCh. 2 - Prob. 2.4QCh. 2 - Prob. 2.5QCh. 2 - Prob. 2.6QCh. 2 - Prob. 2.7QCh. 2 - Prob. 2.8QCh. 2 - Prob. 2.9QCh. 2 - Prob. 2.10Q
Ch. 2 - Prob. 2.11QCh. 2 - Prob. 2.12QCh. 2 - Prob. 2.13QCh. 2 - Prob. 2.14QCh. 2 - Prob. 2.15QCh. 2 - Prob. 2.16QCh. 2 - Prob. 2.17QCh. 2 - Prob. 2.18QCh. 2 - Prob. 2.19QCh. 2 - Prob. 2.20QCh. 2 - Prob. 2.21QCh. 2 - Prob. 2.22QCh. 2 - Prob. 2.23QCh. 2 - Prob. 2.24QCh. 2 - Prob. 2.25QCh. 2 - Prob. 2.26QCh. 2 - Prob. 2.27QCh. 2 - Prob. 2.28QCh. 2 - Prob. 2.29QCh. 2 - Prob. 2.30QCh. 2 - Prob. 2.31QCh. 2 - Prob. 2.32QCh. 2 - Prob. 2.33QCh. 2 - Prob. 2.34QCh. 2 - Prob. 2.35QCh. 2 - Prob. 2.36QCh. 2 - Prob. 2.37QCh. 2 - Prob. 2.38QCh. 2 - Prob. 2.39QCh. 2 - Prob. 2.40QCh. 2 - Prob. 2.41QCh. 2 - Prob. 2.42QCh. 2 - Prob. 2.43QCh. 2 - Prob. 2.44QCh. 2 - Prob. 2.45QCh. 2 - Prob. 2.46QCh. 2 - Prob. 2.47QCh. 2 - Prob. 2.48QCh. 2 - Prob. 2.49PCh. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - Prob. 2.52PCh. 2 - Prob. 2.53PCh. 2 - Prob. 2.54PCh. 2 - Prob. 2.55PCh. 2 - Prob. 2.56PCh. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - Prob. 2.59PCh. 2 - Prob. 2.60PCh. 2 - Prob. 2.61PCh. 2 - Prob. 2.62PCh. 2 - Prob. 2.63PCh. 2 - Prob. 2.64PCh. 2 - Prob. 2.65PCh. 2 - Prob. 2.66PCh. 2 - Prob. 2.67PCh. 2 - Prob. 2.68PCh. 2 - Prob. 2.69PCh. 2 - Prob. 2.70PCh. 2 - Prob. 2.71PCh. 2 - Prob. 2.72PCh. 2 - Prob. 2.73PCh. 2 - Prob. 2.74PCh. 2 - Prob. 2.75PCh. 2 - Prob. 2.76PCh. 2 - Prob. 2.78PCh. 2 - Prob. 2.79PCh. 2 - Prob. 2.80PCh. 2 - Prob. 2.81PCh. 2 - Prob. 2.82PCh. 2 - Prob. 2.83PCh. 2 - Prob. 2.84PCh. 2 - Prob. 2.85PCh. 2 - Prob. 2.86PCh. 2 - Prob. 2.87PCh. 2 - Prob. 2.88PCh. 2 - Prob. 2.89PCh. 2 - Prob. 2.90PCh. 2 - Prob. 2.91PCh. 2 - Prob. 2.92PCh. 2 - Prob. 2.93PCh. 2 - Prob. 2.94PCh. 2 - Prob. 2.95PCh. 2 - Prob. 2.96PCh. 2 - Prob. 2.97PCh. 2 - Prob. 2.98PCh. 2 - Prob. 2.99PCh. 2 - Prob. 2.100PCh. 2 - Prob. 2.101P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine Brinell Hardness Number for a specimen that has a surface area of indentation as 19 mm2 and the applied force as 12 kN.arrow_forward1- With the Vickers hardness test a 10 kg load gave for a sample of brass an indentation with diagonals having mean lengths of 0.510 mm. What is the hardness? Again, what is tensile strength of brass? 2- When a load is applied to a brass specimen in a Brinell test, an indentation of 4.10 mm is Ahimary produced. Estimate the tensile strength of the brass.arrow_forwardA 2.0-inch diameter 4140 steel bar is austenized and tempered in oil without Agitation, determine the resulting hardness at 0.6 inches below the surface, present all the Procedure to arrive at the answer (include sketch of the piece and graph used with steps Using word forms)arrow_forward
- For a certain high-temperature alloy, failure was reported after 4100 hrs at 680°C when subjected to a stress level of 270 MPa. If the same stress were applied at 725°C, how long would the sample be expected to last? State any assumptions you must make to allow you to make this determination.arrow_forwardAn application requires ultimate tensile strength and yield strength ofa steel at 110 ksi and 91 ksi, respectively. Answer the following 4 questions: Can SAE 1040 steel be selected for this application? If “no” is the answer in Part I, the following Part II, III, and IV can beignored. If “yes” is the answer in Part I, which condition of SAE 1040 shouldbe selected? Why is that steel with the condition in part II selected? Is the selected steel brittle or ductile? and Why?arrow_forwardA gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield strength of 370 MPa and a ultimate tensile strength of 440 MPa. What is the punch force needed to punch a square hole with a side length of 20 mm on this HSLA steel? Show your work.arrow_forward
- 3. Consider a test specimen with the shape of cylindrical rod, 120 mm long to be deformed by tensile load of 28000 N without experiencing plastic deformation or diameter reduction more than 8.5x10-3 mm. Which among the aluminium alloy, brass alloy, steel alloy and titanium alloy are possible candidates with yield strengths 200 MPa, 300 MPa, 400 MPa and 650 MPa, respectively.arrow_forward2. A steel of rotating-beam test specimen has an ultimate strength of 1100Mpa. Estimate the fatigue strength of the specimen corresponding to a life of 150k cycles of stress reversal.arrow_forwardDraw a Stress/Strain graph of a mild tensile steel and identify the limit of proportionality and the yield pointarrow_forward
- A part made from hot-rolled AISI 1212 steel undergoes a certain amount of cold-work operation. If the ultimate strength of the material after cold work operation was 80 kpsi. (a) Determine the percentage of cold work (b) Obtain the yield strength after the cold work (c) Determine the hardness of the material before and after the cold work operationarrow_forward(a) A core sample having length to diameter ratio of 2.5 experienced a strain of 0.94 after being stretched. If the core had an initial length of 8 cm and was able to withstand a load of 500 N before breaking, calculate: The resulting length before failure The tensile strength (b) If the core sample above is subjected to a uniaxial compression test resulting in load, axial deformation and circumferential deformation of 350 N, 1.5 and 0.47 respectively at failure, calculate: The uniaxial compressive strength, σc The Young’s modulus, E The Poisson’s ratio,μarrow_forwardTensile and fully reversed loading fatigue tests were conducted for a certain steel alloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa, respectively. If a rod of this material supply were subjected to a static stress of 600 MPa and oscillating stresses whose total range was 700 MPa, would you expect the rod to fail by fatigue processes? Hint: You may want to plot a diagram to aid in presenting your answer.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY