Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6, Problem 32CQ
To determine
The logarithm of ratio initial cross-sectional area to the cross-sectional area at fracture.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The (G-E) diagram obtained in the tensile test performed on a metal sample with a
diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured
on l. 16 cm gauge length were determined as follows:
B
A
B
C
Load (kgf)
4800
8400
7200
Elongation (mm)
0.192
28.8
38.4
c) Calculate the fracture work and the maximum elastic energy the metal rod can store.
d) Find the cross-sectional area of a 6 m long rod made of this metal such that it can carry 12
tons of load with 2 times the safety of yield strength. How long does the rod extend under
this load?
A thin plate of a ceramic material with E = 225 GPa is loaded in tension, developing a stress of 450 MPa. Is the specimen likely to fail if the most severe flaw present is an internal crack oriented perpendicular to the load axis that has a total length 0.25 mm and a crack tip radius of curvature equal to 1 μm?
For a specimen of a steel alloy with a plane strain fracture toughness of 80 MPa√m, fracture results at a stress of 510 MPa when the maximum (or critical) internal crack length is 6 mm. For the same alloy, will fracture occur at a stress level of 380 MPa when the maximum internal crack is 9.0 mm? Why or why not?
Select the most appropriate answer based on your calculation.
Select one:
a. It will not fracture
b. Not enough information
c. It will fracture
Chapter 6 Solutions
Materials Science And Engineering Properties
Ch. 6 - Prob. 1CQCh. 6 - Prob. 2CQCh. 6 - Prob. 3CQCh. 6 - Prob. 4CQCh. 6 - Prob. 5CQCh. 6 - Prob. 6CQCh. 6 - Prob. 7CQCh. 6 - Prob. 8CQCh. 6 - Prob. 9CQCh. 6 - Prob. 10CQ
Ch. 6 - Prob. 11CQCh. 6 - Prob. 12CQCh. 6 - Prob. 13CQCh. 6 - Prob. 14CQCh. 6 - Prob. 15CQCh. 6 - Prob. 16CQCh. 6 - Prob. 17CQCh. 6 - Prob. 18CQCh. 6 - Prob. 19CQCh. 6 - Prob. 20CQCh. 6 - Prob. 21CQCh. 6 - Prob. 22CQCh. 6 - Prob. 23CQCh. 6 - Prob. 24CQCh. 6 - Prob. 25CQCh. 6 - Prob. 26CQCh. 6 - Prob. 27CQCh. 6 - Prob. 28CQCh. 6 - Prob. 29CQCh. 6 - Prob. 30CQCh. 6 - Prob. 31CQCh. 6 - Prob. 32CQCh. 6 - Prob. 33CQCh. 6 - Prob. 34CQCh. 6 - Prob. 35CQCh. 6 - Prob. 36CQCh. 6 - Prob. 37CQCh. 6 - Prob. 38CQCh. 6 - Prob. 1ETSQCh. 6 - Prob. 2ETSQCh. 6 - Prob. 3ETSQCh. 6 - Prob. 4ETSQCh. 6 - Prob. 5ETSQCh. 6 - Prob. 6ETSQCh. 6 - Prob. 7ETSQCh. 6 - Prob. 8ETSQCh. 6 - Prob. 9ETSQCh. 6 - At the ultimate tensile strength. (a) The true...Ch. 6 - Prob. 11ETSQCh. 6 - Prob. 12ETSQCh. 6 - Prob. 13ETSQCh. 6 - Prob. 14ETSQCh. 6 - Prob. 15ETSQCh. 6 - Prob. 16ETSQCh. 6 - Prob. 6.1PCh. 6 - Prob. 6.2PCh. 6 - Compare the engineering and true secant elastic...Ch. 6 - Prob. 6.4PCh. 6 - Prob. 6.5PCh. 6 - An iron specimen is plastically deformed in shear...Ch. 6 - Prob. 6.7PCh. 6 - Prob. 6.8PCh. 6 - Prob. 6.9PCh. 6 - Prob. 6.10PCh. 6 - Prob. 6.11PCh. 6 - Prob. 6.12PCh. 6 - Prob. 6.13PCh. 6 - Prob. 6.14PCh. 6 - Estimate the elastic and plastic strain at the...Ch. 6 - Prob. 6.16PCh. 6 - Prob. 6.17PCh. 6 - Prob. 6.18PCh. 6 - Prob. 6.19PCh. 6 - Prob. 6.1DPCh. 6 - Prob. 6.2DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A ceramic part is used under a complete reverse cyclic stress with a stress amplitude (S) of 250 MPa. The yield strength and fracture toughness of materials is 550 MPa and 12.5 MPa*sqrt(m), respectively. Y is 1.4. What is the critical surface crack length?arrow_forwardcompare the effect of presence of a notch on ductile and brittle materials in terms of fracture behaviourarrow_forward2. a) As an engineer, choose a desired fracture mode in metals with one (1) reason. b) Sketch the fracture behaviour in metals. c) i. The modulus of elasticity of a metal alloy A is 260 GPa. Compute the specific surface energy if propagation of an internal crack of length 0.40 mm is observed when a stress of 63 MPa is applied to the alloy. ii. The elastic deformation energy of alloy A is 3.0 J/m². Based on the answer obtained in c)(i), show whether alloy A is an elastic deformation or a plastic deformation. iii. Interpret if alloy A can be classified as a brittle or a ductile material. d) i. A metal with an internal crack is loaded with a tensile stress of 15 MPa. If the crack length and the radius of curvature are 2.6 x 10-2 mm and 1.1 x 10-4 mm, compute its maximum stress. ii. The modulus of elasticity of the metal is 90 GPa and the specific surface energy is 2.6 J/m2. Based on its critical stress, show that the crack will not grow when a tensile stress of 15 MPa is loaded on it.arrow_forward
- A specimen of a 4340 steel alloy having a plane strain fracture toughness of 45 MPA/M is exposed to a stress of 1000 MPa (145,000 psi). Will this specimen experience fracture if it is known that the largest surface crack is 0.75 mm (0.03 in.) long? Why or why not? Assume that the parameter Y has a value of 1.0.arrow_forward2. Please estimate the number of cycles to failure of a steel specimen under tensile fatigue loading with the following parameters. The R ratio is 3, mean stress 200 MPa, yield strength 450 MPa, ultimate tensile strength 560 MPa, Young’s modulus 200 GPa, KIC = 140 MPa . Assume the initial crack length is 0.1 mm.arrow_forwardA cylindrical tensile specimen has an undeformed diameter of 8.6 mm. It is subjected to a tensile load of 100 kN. The elastic modulus (E) is 10 GPa. Poisson's ratio is 0.25. Calculate the change in the diameter (in mm).arrow_forward
- A structural component in the shape of a flat plate 20.8 mm thick is to be made from a metal with yield strength of 533 MPa and a critical fracture toughness of 22.0 MPa-m!2. Assume a crack forms in the plate, and the geometry of the crack yields a Y value of 1.5. If the plate is designed to a design stress equivalent to 0.3 times the yield strength, what is the critical crack length? Equations: 1/2 () Om К = 2 σο K. = YocTa %3D Ptarrow_forwardThe data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At the fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the proportional limit, modulus of elasticity (i.e the slope of initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percentage reduction in area Tensile-Test Data Load(kN) Elongation (mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracturearrow_forward(b) The difference between the theoretical and measured fracture strengths of brittle materials is explained by the presence of small flaws or cracks. In terms of these pre-existing flaws or cracks, briefly describe the occurring phenomena when a brittle material fractures in tension. (i) (ii) Explain why ductile materials do not fail in a brittle manner even though they have small flaws and crack present. If so, explain the process of ductile fracture of the materials.arrow_forward
- A metallic rod of diameter do is subjected to the tensile test. The engineering stress and the true stress at fracture are 800 MPa and 900 MPa, respectively. The ratio of the rod diameter at fracture df to the initial diameter do is (round off to 2 decimal places)arrow_forwardA brass specimen of the circular cross-section is fractured at 151 kN force and the final length of the specimen at fracture is 49 mm. The fracture strength of the specimen is found to be 74 kN/mm2. The percentage of elongation of the specimen is 42 %. Determine the following (i) Diameter of the specimen ii) Initial length of the specimen iii) Stress under an elastic load of 16 kN iv) Young's Modulus if the elongation is 1.6 mm at 16 kN (v) Final diameter if the percentage of reduction in area is 20 % solve: Initial Cross-sectional Area (in mm2) = The Diameter of the Specimen (in mm) = Initial Length of the Specimen (in mm) =arrow_forwardQuestion 1 The ideal diameter of a steel tensile test specimen is 1 in 2 in 1/2 in 1/4 in Question 2 How many zones are exhibited by a typical stress- strain diagram 4 2arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning