Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 3, Problem 3.29P
(a)
To determine
The heat transfer through a wall.
(b)
To determine
The plot for temperature distribution within wall.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
under steady-state conditions. If you are given T1 = 200 °C and T2 = 164 °C, determine:
a) the conduction heat flux, q,.cond, in
m2
W
from x = 0 to x = L
b) if the dimensions of the triangle ares 15 mm and h 13 mm, calculate the heat
transfer due to convection, q,y, in W at x = L
Finsulation
T2
T
T = 20°C
h = 500 W/m2.K
Triangular Prism
x L
x 0
L= 50 mm
k = 100 W/m-K
Q1/ A thick wall consists two layers of Gypsum, insulation and brick as shown in
figure below. The ambient temperature is 20 °C and heat transfer coefficient is 5
Wim2. K in the left side. The surface temperature of right side is 45 °C. find the
heat losses per meter length. What will happen if the insulation's thickness
* increases by 25%
Gypsum k = 0.04W/m. K
T= 45 °C
h=5 W/m'. K
T = 20 °C
5 cm
Insulation
k=0.04W/m. K
Brick
k=0.69 W/m. K
1. Temperatures are measured at the left-hand face and at a point 4 cm from the left-hand
face of the planar wall shown in the figure below. These temperatures are T₁ = 45.3 °C
and T* = 21.2 °C. The heat flow through the planar wall is steady and one dimensional.
What is the value of T2 at the right-hand surface of the wall?
TI
T*
4 cm
10 cm
T2
Chapter 3 Solutions
Introduction to Heat Transfer
Ch. 3 - Consider the plane wall of Figure 3.1, separating...Ch. 3 - A new building to be located in a cold climate is...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - A dormitory at a large university, built 50 years...Ch. 3 - In a manufacturing process, a transparent film is...Ch. 3 - Prob. 3.7PCh. 3 - A t=10-mm-thick horizontal layer of water has a...Ch. 3 - Prob. 3.9PCh. 3 - The wind chill, which is experienced on a cold,...
Ch. 3 - Prob. 3.11PCh. 3 - A thermopane window consists of two pieces of...Ch. 3 - A house has a composite wall of wood, fiberglass...Ch. 3 - Prob. 3.14PCh. 3 - Prob. 3.15PCh. 3 - Work Problem 3.15 assuming surfaces parallel to...Ch. 3 - Consider the oven of Problem 1.54. The walls of...Ch. 3 - The composite wall of an oven consists of three...Ch. 3 - The wall of a drying oven is constructed by...Ch. 3 - The t=4-mm-thick glass windows of an...Ch. 3 - Prob. 3.21PCh. 3 - In the design of buildings, energy conservation...Ch. 3 - Prob. 3.23PCh. 3 - Prob. 3.24PCh. 3 - Prob. 3.25PCh. 3 - A composite wall separates combustion gases at...Ch. 3 - Prob. 3.27PCh. 3 - Prob. 3.28PCh. 3 - Prob. 3.29PCh. 3 - The performance of gas turbine engines may...Ch. 3 - A commercial grade cubical freezer, 3 m on a...Ch. 3 - Prob. 3.32PCh. 3 - Prob. 3.33PCh. 3 - Prob. 3.34PCh. 3 - A batt of glass fiber insulation is of density...Ch. 3 - Air usually constitutes up to half of the volume...Ch. 3 - Prob. 3.37PCh. 3 - Prob. 3.38PCh. 3 - The diagram shows a conical section fabricatedfrom...Ch. 3 - Prob. 3.40PCh. 3 - From Figure 2.5 it is evident that, over a wide...Ch. 3 - Consider a tube wall of inner and outer radii ri...Ch. 3 - Prob. 3.43PCh. 3 - Prob. 3.44PCh. 3 - Prob. 3.45PCh. 3 - Prob. 3.46PCh. 3 - To maximize production and minimize pumping...Ch. 3 - A thin electrical heater is wrapped around the...Ch. 3 - Prob. 3.50PCh. 3 - Prob. 3.51PCh. 3 - Prob. 3.52PCh. 3 - A wire of diameter D=2mm and uniform temperatureT...Ch. 3 - Prob. 3.54PCh. 3 - Electric current flows through a long rod...Ch. 3 - Prob. 3.56PCh. 3 - A long, highly polished aluminum rod of diameter...Ch. 3 - Prob. 3.58PCh. 3 - Prob. 3.59PCh. 3 - Prob. 3.60PCh. 3 - Prob. 3.61PCh. 3 - Prob. 3.62PCh. 3 - Consider the series solution, Equation 5.42, for...Ch. 3 - Prob. 3.64PCh. 3 - Copper-coated, epoxy-filled fiberglass circuit...Ch. 3 - Prob. 3.66PCh. 3 - A constant-property, one-dimensional Plane slab of...Ch. 3 - Referring to the semiconductor processing tool of...Ch. 3 - Prob. 3.69PCh. 3 - Prob. 3.70PCh. 3 - Prob. 3.71PCh. 3 - The 150-mm-thick wall of a gas-fired furnace is...Ch. 3 - Steel is sequentially heated and cooled (annealed)...Ch. 3 - Prob. 3.74PCh. 3 - Prob. 3.75PCh. 3 - Prob. 3.76PCh. 3 - Prob. 3.77PCh. 3 - Prob. 3.78PCh. 3 - The strength and stability of tires may be...Ch. 3 - Prob. 3.80PCh. 3 - Prob. 3.81PCh. 3 - A long rod of 60-mm diameter and thermophysical...Ch. 3 - A long cylinder of 30-min diameter, initially at a...Ch. 3 - Work Problem 5.47 for a cylinder of radius r0 and...Ch. 3 - Prob. 3.85PCh. 3 - Prob. 3.86PCh. 3 - Prob. 3.87PCh. 3 - Prob. 3.88PCh. 3 - Prob. 3.89PCh. 3 - Prob. 3.90PCh. 3 - Prob. 3.91PCh. 3 - Prob. 3.92PCh. 3 - In Section 5.2 we noted that the value of the Biot...Ch. 3 - Prob. 3.94PCh. 3 - Prob. 3.95PCh. 3 - Prob. 3.96PCh. 3 - Prob. 3.97PCh. 3 - Prob. 3.98PCh. 3 - Work Problem 5.47 for the case of a sphere of...Ch. 3 - Prob. 3.100PCh. 3 - Prob. 3.101PCh. 3 - Prob. 3.102PCh. 3 - Prob. 3.103PCh. 3 - Consider the plane wall of thickness 2L, the...Ch. 3 - Problem 4.9 addressed radioactive wastes stored...Ch. 3 - Prob. 3.106PCh. 3 - Prob. 3.107PCh. 3 - Prob. 3.108PCh. 3 - Prob. 3.109PCh. 3 - Prob. 3.110PCh. 3 - A one-dimensional slab of thickness 2L is...Ch. 3 - Prob. 3.112PCh. 3 - Prob. 3.113PCh. 3 - Prob. 3.114PCh. 3 - Prob. 3.115PCh. 3 - Derive the transient, two-dimensional...Ch. 3 - Prob. 3.117PCh. 3 - Prob. 3.118PCh. 3 - Prob. 3.119PCh. 3 - Prob. 3.120PCh. 3 - Prob. 3.121PCh. 3 - Prob. 3.122PCh. 3 - Consider two plates, A and B, that are each...Ch. 3 - Consider the fuel element of Example 5.11, which...Ch. 3 - Prob. 3.125PCh. 3 - Prob. 3.126PCh. 3 - Prob. 3.127PCh. 3 - Prob. 3.128PCh. 3 - Prob. 3.129PCh. 3 - Consider the thick slab of copper in Example 5.12,...Ch. 3 - In Section 5.5, the one-term approximation to the...Ch. 3 - Thermal energy storage systems commonly involve a...Ch. 3 - Prob. 3.133PCh. 3 - Prob. 3.134PCh. 3 - Prob. 3.135PCh. 3 - A tantalum rod of diameter 3 mm and length 120 mm...Ch. 3 - A support rod k=15W/mK,=4.0106m2/s of diameter...Ch. 3 - Prob. 3.138PCh. 3 - Prob. 3.139PCh. 3 - A thin circular disk is subjected to induction...Ch. 3 - An electrical cable, experiencing uniform...Ch. 3 - Prob. 3.142PCh. 3 - Prob. 3.145PCh. 3 - Consider the fuel element of Example 5.11, which...Ch. 3 - Prob. 3.147PCh. 3 - Prob. 3.148PCh. 3 - Prob. 3.149PCh. 3 - Prob. 3.150PCh. 3 - In a manufacturing process, stainless steel...Ch. 3 - Prob. 3.153PCh. 3 - Carbon steel (AISI 1010) shafts of 0.1-m diameter...Ch. 3 - A thermal energy storage unit consists of a large...Ch. 3 - Small spherical particles of diameter D=50m...Ch. 3 - A spherical vessel used as a reactor for producing...Ch. 3 - Batch processes are often used in chemical and...Ch. 3 - Consider a thin electrical heater attached to a...Ch. 3 - An electronic device, such as a power transistor...Ch. 3 - Prob. 3.161PCh. 3 - In a material processing experiment conducted...Ch. 3 - Prob. 3.165PCh. 3 - Prob. 3.166PCh. 3 - Prob. 3.167PCh. 3 - Prob. 3.168PCh. 3 - Prob. 3.173PCh. 3 - Prob. 3.174PCh. 3 - Prob. 3.175PCh. 3 - Prob. 3.176PCh. 3 - Prob. 3.177P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q1/ A thick wall consists two layers of Gypsum, insulation and brick as shown in figure below. The ambient temperature is 20 °C and heat transfer coefficient is 5 W/m2. K in the left side. The surface temperature of right side is 45 °C. find the heat losses per meter length. What will happen if the insulation's thickness * .increases by 25% Gypsum k = 0.04W/m. K T = 45 °C h=5 W/m'. K T. = 20 °C 5 cm Insulation k = 0.04W/m. K Brick k = 0.69 W/m. Karrow_forwardA square steel bar of side length w = 0.21 m has a thermal conductivity of k = 15.6 J/(s⋅m⋅°C) and is L = 2.7 m long. One end is placed near a blowtorch so that the temperature is T1 = 95° C while the other end rests on a block of ice so that the temperature is a constant T2. a. input an expression for the heat transferred to the cold end of the bar as a function of time using A=w^2 as the cross-sectional area of the bar. b. how much energy in joules was conducted in 1 hour, assuming t2=0*C c. input an expression for the mass of the water melted in one hour using Q1 from above and Lf in the latent heat of fusion. mw=arrow_forwardThe annual fixed costs for insulating a certain steam pipe installation can be expressed as Cf = 30S + 40 dollar per year where S is thickness of insulation in inches, and the annual cost of energy lost (annual direct costs) from the installation may be expressed in terms of the insulation thickness as Cp = 100/S $ per year. Determine the optimum annual insulation thickness cost.arrow_forward
- A thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 300 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant O degrees C. Let u(x, t) be the temperature in the bar at x at timet, with t measured in seconds. Find u(x, t) and then u7 (2, 0.1). Put uz (2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.arrow_forward= Consider a large plane wall of thickness L=0.3 m, thermal conductivity k = 2.5 W/m.K, and surface area A = 12 m². The left side of the wall at x=0 is subjected to a net heat flux of ɖo = 700 W/m² while the temperature at that surface is measured to be T₁ = 80°C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary equations for steady one- dimensional heat conduction through the wall, (b) obtain a relation for the variation of the temperature in the wall by solving the differential equation, and (c) evaluate the temperature of the right surface of the wall at x=L. Ti до L Xarrow_forwardA house, for cooling purposes, consists of two zones: the attic area zone A and the living area zone B (see below figure). The living area is cooled by a 2-ton air conditioning unit that removes 31,000 Btu/hr. The heat capacity of zone B is 8. °F per thousand Btu. The time constant for heat transfer between zone A and the outside is 4 hr, between zone B and the outside is 8 hr, and between the two zones is 8 hr. If the outside temperature stays at 90°F, how warm does it eventually get in the attic zone A? .... It eventually gets to be (Type an integer or decimal rounded to the nearest hundredth as needed.) °F in the attic zone A.arrow_forward
- Q1. Consider a plane wall (thermal conductivity, k = 0.8 W/mK, and thickness, fb1 = 100 mm) of a house as shown in Fig. Q1(a). The outer surface of the wall is exposed to solar radiation and has an absorptivity of a = 0.5 for solar energy, or=600 W/m². The temperature of the interior of the house is maintained at T1 = 25 °C, while the ambient air temperature outside remains at T2 = 5 °C. The sky, the ground and the surfaces of the surrounding structures at this location can be modelled as a surface at an effective temperature of Tsky = 255 K for radiation exchange on the outer surface. The radiation exchange inside the house is negligible. The convection heat transfer coefficients on the inner and the outer surfaces of the wall are h₁ = 5 W/m²-K and /1₂ = 20 W/m².K, respectively. The emissivity of the outer surface is = 0.9. T1 = 25 °C Ţ₁ Too1 = 25 °C T₁ k 100 mm Fig. Q1(a) Assuming the heat transfer through the wall to be steady and one-dimensional: (a) Solve the steady 1D heat…arrow_forwardA thin bar of length L = 3 meters is situated along the x axis so that one end is at x = 0 and the other end is at x = 3. The thermal diffusivity of the bar is k = 0.4. The bar's initial temperature f(x) = 50 degrees Celsius. The ends of the bar (x = 0 and x = 3) are then put in an icy bath and kept at a constant 0 degrees C. Let u(x, t) be the temperature in the bar at x at time t, with t measured in seconds. Find u(x, t) and then u4 (2, 0.1). Put u4(2, 0.1) calculated accurately to the nearest thousandth (3 decimal places) in the answer box.arrow_forwardFind the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K)arrow_forward
- Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTUarrow_forward4x F2 # 3 E 4, F3 54 $ R F4 Ac = 1m² ▬ H DII x= 1 m (4) Consider a wall (as shown above) of thickness L-1 m and thermal conductivity k-1 W/m-K. The left (x=0) and the right (x=1 m) surfaces of the wall are subject to convection with a convectional heat transfer coefficient h= 1 W/m²K and an ambient temperature T. 1 K. There is no heat generation inside the wall. You may assume 1-D heat transfer, steady state condition, and neglect any thermal contact resistance. Find T(x). % To,1 = 1 K h₁ = 1 W/m²K 5 Q Search F5 T T₁ A 6 x=0 F6 à = 0 W/m³ k= 1W/mK L=1m Y 994 F7 & 7 T₂ U Ton2 = 1 K h₂ = 1 W/m²K1 PrtScn F8 Page of 7 ) 0 PgUp F11 Parrow_forwardA 25 cm diameter steel oil pipe line located in the desert of Saudi Arabia is insulated with 9 cm insulator. The temperature between the pipe and insulator is 36℃ and the outer part of the insulator is 78℃. The pipe length is 10 m and the outside film conductance is 0.5W/(m^2℃). Find the heat absorbed per length if the inside film conductance is 9.8W/(m^2℃).arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license