Foundations of Materials Science and Engineering
6th Edition
ISBN: 9781259696558
Author: SMITH
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 13.10, Problem 81SEP
To determine
Material for fastening the brass has to be selected based on the marine environment.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A fillet weld on low carbon steel has a cross‑sectional area of 25.0 mm2 and is 900 mm long. Determine (a) the amount of heat required to perform the weld, and (b) the amount of heat that must be generated by the heat source, if the heat transfer factor = 0.90 and the melting factor = 0.60?
A 6061-T4 aluminum alloy is to be used to make a thin-walled cylindrical canister in which high-pressure chemical reactions will be performed. The design calls for a diameter of 50 cm, a length of 80 cm, and a maximum operating pressure of 5 MPa. Assume a safety factor of four is required (i.e., the maximum stress can never exceed onequarter of the alloy’s yield strength). a. What wall thickness is required to ensure safe operation? b. Is this wall thickness a maximum or a minimum? Explain. c. How do your answers change if the cylinder is made twice as long?
Two 3.5 mm thick metal (Um = 9.5 J/mm?)
sheets are being joined using resistance spot welding. To achieve
required strength, it is desired to form a weld nugget that is 5.5 mm in
diameter and 4.0 mm thick. The weld duration will be set at 0.3 sec. If
the electrical resistance between the surfaces is 140 microohms, and
only onethird of the electrical energy generated will be used to form the
weld nugget determine the current.
Chapter 13 Solutions
Foundations of Materials Science and Engineering
Ch. 13.10 - Prob. 1KCPCh. 13.10 - Prob. 2KCPCh. 13.10 - Which is in a lower energy state: (a) elemental...Ch. 13.10 - Give several examples of environmental...Ch. 13.10 - Prob. 5KCPCh. 13.10 - Prob. 6KCPCh. 13.10 - Prob. 7KCPCh. 13.10 - What is an exchange current density? What is the...Ch. 13.10 - Prob. 9KCPCh. 13.10 - Prob. 10KCP
Ch. 13.10 - Prob. 11KCPCh. 13.10 - Prob. 12KCPCh. 13.10 - Prob. 13KCPCh. 13.10 - Prob. 14KCPCh. 13.10 - Prob. 15KCPCh. 13.10 - Prob. 16KCPCh. 13.10 - Prob. 17KCPCh. 13.10 - Prob. 18KCPCh. 13.10 - Prob. 19KCPCh. 13.10 - Describe fretting corrosion.Ch. 13.10 - What is selective leaching of an alloy? Which...Ch. 13.10 - Prob. 22KCPCh. 13.10 - Prob. 23KCPCh. 13.10 - Prob. 24KCPCh. 13.10 - Prob. 25KCPCh. 13.10 - Prob. 26KCPCh. 13.10 - Prob. 27KCPCh. 13.10 - What are Alclad alloys?Ch. 13.10 - Prob. 29AAPCh. 13.10 - Prob. 30AAPCh. 13.10 - Prob. 31AAPCh. 13.10 - Prob. 32AAPCh. 13.10 - Prob. 33AAPCh. 13.10 - The emf of a standard Ni-Cd galvanic cell is...Ch. 13.10 - What is the emf with respect to the standard...Ch. 13.10 - Prob. 36AAPCh. 13.10 - Prob. 37AAPCh. 13.10 - Prob. 38AAPCh. 13.10 - Prob. 39AAPCh. 13.10 - Prob. 40AAPCh. 13.10 - Prob. 41AAPCh. 13.10 - Prob. 42AAPCh. 13.10 - Prob. 43AAPCh. 13.10 - Prob. 44AAPCh. 13.10 - Prob. 45AAPCh. 13.10 - Prob. 46AAPCh. 13.10 - Prob. 47AAPCh. 13.10 - Prob. 48AAPCh. 13.10 - Prob. 49AAPCh. 13.10 - Prob. 50AAPCh. 13.10 - Prob. 51AAPCh. 13.10 - Prob. 52AAPCh. 13.10 - Prob. 53AAPCh. 13.10 - Prob. 54AAPCh. 13.10 - A galvanized (zinc-coaled) steel sheet is found to...Ch. 13.10 - Prob. 56AAPCh. 13.10 - Prob. 57AAPCh. 13.10 - Prob. 58AAPCh. 13.10 - Prob. 59AAPCh. 13.10 - Prob. 60AAPCh. 13.10 - Prob. 61AAPCh. 13.10 - Prob. 62AAPCh. 13.10 - Prob. 63AAPCh. 13.10 - Prob. 64AAPCh. 13.10 - Prob. 65AAPCh. 13.10 - Prob. 66AAPCh. 13.10 - Prob. 67AAPCh. 13.10 - Prob. 68AAPCh. 13.10 - Prob. 69AAPCh. 13.10 - Prob. 70AAPCh. 13.10 - Prob. 71AAPCh. 13.10 - Prob. 72AAPCh. 13.10 - Prob. 73AAPCh. 13.10 - Prob. 74AAPCh. 13.10 - Prob. 75AAPCh. 13.10 - Prob. 76SEPCh. 13.10 - Prob. 77SEPCh. 13.10 - Prob. 78SEPCh. 13.10 - Prob. 79SEPCh. 13.10 - Prob. 80SEPCh. 13.10 - Prob. 81SEPCh. 13.10 - Prob. 82SEPCh. 13.10 - Prob. 83SEPCh. 13.10 - Prob. 84SEPCh. 13.10 - Corrosion is observed at the root of threads on...Ch. 13.10 - Prob. 86SEPCh. 13.10 - Prob. 87SEPCh. 13.10 - Prob. 88SEPCh. 13.10 - Prob. 89SEPCh. 13.10 - Prob. 90SEPCh. 13.10 - Prob. 91SEPCh. 13.10 - Prob. 92SEPCh. 13.10 - Prob. 93SEPCh. 13.10 - Prob. 94SEPCh. 13.10 - Prob. 95SEPCh. 13.10 - Prob. 96SEPCh. 13.10 - Prob. 97SEPCh. 13.10 - Prob. 98SEP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The welding parameters to be used to butt weld a metal alloy are being evaluated. In order to set up the welding machine, the melting factor for the metal (f2) has to be determined. The welding machine can deliver 4000 watts of power and the heat transfer factor for the welding process (f1) is 0.9. The final weld bead consists of 8 0% filler metal and 40% parent metal. The melting temperature of the filler metal and the parent metal is the same 2540 deg F. The cross-sectional area of the weld bead is 0.5 sq inches. The rate at which filler metal is added to the weld is 1 cu inch per min. Conversion factor 1 Btu = 1055 J and 0 deg F = 460 deg R Calculate the melting factor.arrow_forwardQuestion 41. Two 10-mm-thick by 60-mm wide hot rolled SAE 1050 steel plates are to be butt-welded together with a CJP weld. Choose an appropriate electrode for tensile loading of the joint. 2. Find the torque that a 2-surface dry disk clutch can transmit if the outside and inside lining diameters are 120 mm and 70 mm, respectively, and the applied force is 10 kN. Assume uniform wear and μ = 0.4.arrow_forwardQuestion 1 1.1 Identify the weld defect shown in Figure 1 below. Provide reasons for your selection. Figure 1: Weld defect 1.2 Explain how the weld defect, shown in Figure 1, can occur. 1.3 Identify the joining process shown in Figure 2 and explain why this process is frequently used by automotive manufacturers. Figure 2: Joining process frequently used by automotive manufacturers 1.4 Explain the main differences between the joining process shown in Figure 2 and fusion welding processes. 1.5 Name important design considerations applicable to the joining process shown in Figure 2.arrow_forward
- An electron-beam welding operation will join two pieces of steel plate together. The plates are 2.5 cm thick. The unit melting energy is 8050 J/cm3. The diameter of the work area focus of the beam is 0.15 cm, hence the width of the weld will be 0.15 cm. The accelerating voltage is 30 kV and the beam current is 35 milliamp. The heat transfer factor is 0.70 and the melting factor is 0.55. If the beam moves at a speed of 125 cm/min, will the beam penetrate the full thickness of the platesarrow_forwardA U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U-groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?arrow_forwardA U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U- groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. Tm for titanium is 2070°K (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?arrow_forward
- Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?arrow_forwardQuestion No. 11: (a) Illustrate flatness, straightness and circularity with symbol. (b) A circular shaft, 80 mm in diameter is welded to support by means of a circumferential fillet weld. It is subjected to a torsion moment of 3000 N-m. Determine the size of weld, if the maximum shear stress in the weld is not to exceed 70 N/mm2 . (c) Analyze different stresses during design of screw and nutarrow_forwardProvide a reasonable explanation for the following observation: a welded component made of Al 6061-T6 alloy is routinely found to deform plastically first in the region adjacent to the weld joint despite the fact that the stress is nominally the same everywhere in the component. What solution would you propose to fix this problem, assuming that the weld joint cannot be eliminated from the design?arrow_forward
- An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?arrow_forward9. Calculate if a plate of SA-302-A with a thickness of 4.5 mm being made into a boiler drum meets code. Internal diameter is 0.350m with a maximum allowable working pressure of 1450 kPa at a temperature of 475 °C. Joint Efficiency is 70% with no addition thickness required for corrosion. If the thickness 4.5 mm. Confirm this meets code requirements.arrow_forwardQUESTION 6 What is the safety factor for this weld? F=671 Ibf, b=1 in; d=2.2 in; h=1/4 in. The weld metal is E7018, and the member is 10 in long. y F harrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Heat Transfer [Conduction, Convection, and Radiation]; Author: Mike Sammartano;https://www.youtube.com/watch?v=kNZi12OV9Xc;License: Standard youtube license