Afire nozzle is supplied through 300 ft of 3-in.-diameter canvas hose with e = 0:001 ft. Water from a hydrant is supplied at 50 psig to a booster pump on board the pumper truck. At design operating conditions, the pressure at the nozzle inlet is 100 psig and the pressure drop along the hose is 33 psi per 100 ft of length. Calculate the design flow rate and the maximum nozzle exit speed. Select a pump appropriate for this application, determine its efficiency at this operating condition, and calculate the power required to drive the pump.
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Additional Engineering Textbook Solutions
Introduction to Heat Transfer
Fundamentals Of Thermodynamics
DeGarmo's Materials and Processes in Manufacturing
Engineering Mechanics: Dynamics (14th Edition)
Mechanics of Materials
Applied Fluid Mechanics (7th Edition)
- 2. Water from a reservoir is pump over a hill through a pipe 900mm in diameter and a pressure of one kg/cm² is maintained at the pipe discharge where the pipe is 85m from the pump centerline. The pumps have a positive suction head of 5m. Pumping rate or the pump at 1000 rpm is 1.5m³/sec. Friction losses is equivalent to 3m of head loss. What is the head that should the pump cover for the system?arrow_forwardA submersible pump is to be selected for the installation on a newly drilled deep well. The static water level (SWL) of the water inside the well is 8.7m from the natural ground level and the centerline of the discharge pipeline is 3.5 feet above the natural ground level. Based on the test pumping results from the SWL the flow velocity at the pipeline discharge was 8.09 ft/s and the design pressure is 40 psi to assure that the water can reach the elevated water tank. The total head losses are assumed to be 12 feet. a.) Find the total dynamic head (TDH) of the submersible pump needed for sizing in feet ? b.) What will be the suitable pipe diameter for the system riser in inches?arrow_forward3. A centrifugal pump is to be placed above a large, open water tank, as shown in the figure below. Water is pumped at a rate of I cu ft/s. At this flow rate the required net positive suction head, NPSHR, is 15 ft as specified by the pump manufacturer. The water temperature is 80°F and atmospheric pressure is 14.7 psi. Assume that the major head loss between the tank and the pump inlet is due to filter at the pipe inlet having a minor loss coefficient KL.-20. Other losses can be neglected. The pipe on the suction side of the pump has a diameter of 5 in. The water vapor pressure at 80°F is 0.5069 psia and y-62.22 lb/cu.ft. Determine Z1 for cavitation not to occur.. P1-Patm (1) (2) Reference planearrow_forward
- Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of the piping is in 5-in. schedule 40 steel pipe. If the 2 fittings used is 90° ell standard long radius, The pump has an efficiency of 80%. Calculate the kW power needed for the pump. Calculate the total friction losses in kJ/kg.arrow_forwardQuestion #2 Calculate the Net Positive Suction Head (NPSH) for a pump handling 100,000 kg/hr flow of water coming from an atmospheric storage tank. The water temperature can be taken as 25°C. The pump suction nozzle is 0.4 m above ground level. The tank is elevated on a 1 m high platform. The minimum liquid level in the tank is 300 mm. Consider the line losses of 0.77.arrow_forwardExercise Problem No. 1: An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12,500 liters/min.at normal temperature. Calculate the following: 1.Head at the discharge side, m 2. Velocity Head, m 3. Total Head of the pump, marrow_forward
- 5. Oil of specific gravity 0.750 is pumped from a tank over a hill through a 24′′ pipe with the pressure at the top of the hill maintained at 25.5 psi. The summit is 250 ft above the surface of the oil in the tank, and oil is pumped at the rate of 22.0 cfs. If the lost head from tank to summit is 15.7 ft, what horsepower must the pump supply to the liquid? indicate free body diagramarrow_forwardFind the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm e. a 15 ft Plenum е 15 ft 5 ft 5 ft a 3. 20 ft 4 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a d earrow_forwardThe pressure drop across a turbine is 25 psi. The flow rate is 55gal/min. Calculate the power output of the turbine.arrow_forward
- QUESTION 1 Figure 1 shows water at 20°C to be circulated from and to the reservoir. The 30 mm diameter pipe made of commercial steel, 60 m long is to be used. Water will be pumped by a 65% efficient motor-pump combination that draws 400 W of electric power during operation. Estimate the total volume flow rate through the valve. KL exit = 1.0 KL elbow = 1.5 KL = 0.8 KL Filter KL valve 6.0 = 12.0 filter H Pump Figure 1 Lentarrow_forwardA piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping powerwith given flow conditions. Discuss the results. Flow conditions are same for both type of designs and given as: Pipe material: stainless steel Volume flow rate: 40 L/sec Assume the working fluid is water at standard atmosphere temperature and both tanks areopen to atmosphere. Pipe inlet is sharp-edged and bends are sharped without vanes. Elevations are as ?? = ?? ? and ?? = ?? ?arrow_forward. What horsepower is supplied to air moving at 7m/min through a 70cmx90cm duct under a pressure of8cm of H2O?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY