Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm a 15 ft Plenum e 15 ft 5 ft a d. 5 ft 20 ft 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a C d. e

Find the loss in total pressure for each run in the simple duct system of Fig. 1, using the equal-friction method and in English unit. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Duct fittings are listed in Table 1. Assume the duct dimeter in run 1 is 10 in. and the rest are 8 in. Does the duct system require any adjustment? 150 cfm a 15 ft Plenum e 15 ft 5 ft a d. 5 ft 20 ft 10 ft 200 cfm e 10 ft 150 cfm b Duct Fittings for Figure 1 Fittings Type Abrupt Entrance 90 deg Elbow, Pleated Round to Rectangular boot, Straight 45 deg. Converging Wye 45 deg Elbow, Pleated a C d. e

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
The longest pipe run for a hot water system is 100 m. If the pressure rise through the pump is 35 kPa, then the pressure drop per one meter in system is إختر أحد الخيارات: Pa/m 233.3 .a O Pa/m 400 .bO Pa/m 250 .c O Pa/m 375 .d O
Q1/ liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to 45° elbow 8 m Fig. (1) Globe valve Tank 5 m supply water to the tank at the rate of 245 I/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the pump required 12 m NPSH is it suitable to prevent cavitation for this system? why? Given that: u = 0.0016 Pa.s; p 850 kg/m', e/d 0.0035, (Le/d) of Globe valve (open) = 240 (Le/d) of 45° ēlbow = 24 and Pv = 36.6 kPa 25 m 45° Reservoir 45° elbow
What is the time is taken by the system to fill a tank of capacity 315 liters and flow rate 25 x 10 3 m³ per hour?
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
Air flowing through a 300 mm X 500 mm duct gives velocity pressure reading of 6 mm H2O W.G. What is the volumetric air flow rate in liters/min?
. What horsepower is supplied to air moving at 7m/min through a 70cmx90cm duct under a pressure of8cm of H2O?
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (2) Select the correct simplified general energy equation for point 1 and 2
The water turbine of a 5-MW hydro-power plant has specific speed of 40 rpm and discharge of 2020 lps. What is the approximate diameter of the jet in mm?
Exercise : The losses per unit length pipeAh/l in turbulent flow through small pipe depend upon Velocity, Diameter, Gravity, Dynamic viscosity and Density. Determine the general from of equation.