Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 89P
To determine
The speed of the compressor and the mass flow rate during the test.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An ammonia refrigerator produces 30 tonnes of ice from ant at 0 °C in 24 hours. The temperature range of the compressor is 25 °C to -15 °C. The vapour is dry saturated at the end of compression. Assume a coefficient of performance to be 60% of the theoretical value. Calculate the power required to drive the compressor. Latent heat of ice = 135 kJ/kg. Properties of ammonia are as follows:Temperat ureEnthalpy (kJ/kg)Specific entropy (kJ/kg-K)(oC) Liquid Vapour (hf) (hg)Vapor (Sf) (Sg)Liquid25 -15298.90 1465.84 112.34 1426.541.1242 0.45725.0391 5.5490
Consider an engine with a maximum speed of 7000 rpm. The bore and stroke are 0.1 m, each. For an inlet air temperature of 330 K, determine the intake valve area (assume single valve per cylinder and take k=1.4).
Show the arrangement of blades in an axial compressor with twostages. Show graphically the variation of static pressure andabsolute velocity through the machine. Why is this type ofcompressor more suitable for a turbo-jet engine?
Chapter 10 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 10 - The geometry of a centrifugal water pump is r1 =...Ch. 10 - Find the resulting -groups when (a) D, , and Q or...Ch. 10 - Consider the centrifugal pump impeller dimensions...Ch. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - Dimensions of a centrifugal pump impeller areCh. 10 - The blade is one of a series. Calculate the force...Ch. 10 - This blade is one of a series. What force is...Ch. 10 - A centrifugal water pump, with 15-cm-diameter...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - A series of blades, such as in Example 10.13,...
Ch. 10 - In passing through this blade system, the absolute...Ch. 10 - A centrifugal pump runs at 1750 rpm while pumping...Ch. 10 - A centrifugal water pump designed to operate at...Ch. 10 - Kerosene is pumped by a centrifugal pump. When the...Ch. 10 - In the water pump of Problem 10.8, the pump casing...Ch. 10 - Use data from Appendix C to choose points from the...Ch. 10 - Data from tests of a water suction pump operated...Ch. 10 - A centrifugal pump impeller having r1 = 50 mm, r2...Ch. 10 - A centrifugal pump impeller having dimensions and...Ch. 10 - An axial-flow fan operates in sea-level air at...Ch. 10 - Data measured during tests of a centrifugal pump...Ch. 10 - A small centrifugal pump, when tested at N = 2875...Ch. 10 - If the impeller of Problem 10.20 rotates between...Ch. 10 - At the outlet of a pump impeller of diameter 0.6 m...Ch. 10 - Typical performance curves for a centrifugal pump,...Ch. 10 - A pump with D = 500 mm delivers Q = 0.725 m3/s of...Ch. 10 - At its best efficiency point ( = 0.87), a...Ch. 10 - Using the performance curves in Appendix C, select...Ch. 10 - A pumping system must be specified for a lift...Ch. 10 - A centrifugal water pump operates at 1750 rpm; the...Ch. 10 - A set of eight 30-kW motor-pump units is used to...Ch. 10 - A blower has a rotor with 12-in. outside diameter...Ch. 10 - A centrifugal water pump has an impeller with an...Ch. 10 - Appendix C contains area bound curves for pump...Ch. 10 - Use data from Appendix C to verify the similarity...Ch. 10 - A centrifugal water pump has an impeller with...Ch. 10 - Catalog data for a centrifugal water pump at...Ch. 10 - A 1/3 scale model of a centrifugal water pump...Ch. 10 - Sometimes the variation of water viscosity with...Ch. 10 - A large deep fryer at a snack-food plant contains...Ch. 10 - Data from tests of a pump, with a...Ch. 10 - A four-stage boiler feed pump has suction and...Ch. 10 - A centrifugal pump operating at N = 2265 rpm lifts...Ch. 10 - A centrifugal pump is installed in a piping system...Ch. 10 - Part of the water supply for the South Rim of...Ch. 10 - Consider the flow system shown in Problem 8.94....Ch. 10 - Afire nozzle is supplied through 300 ft of...Ch. 10 - Performance data for a centrifugal fan of 3-ft...Ch. 10 - The performance data of Problem 10.57 are for a...Ch. 10 - Experimental test data for an aircraft engine fuel...Ch. 10 - Preliminary calculations for a hydroelectric power...Ch. 10 - Conditions at the inlet to the nozzle of a Pelton...Ch. 10 - A Francis turbine is to operate under a head of 46...Ch. 10 - A Kaplan (propeller with variable-pitch blades)...Ch. 10 - Francis turbine Units 19, 20, and 21, installed at...Ch. 10 - Measured data for performance of the reaction...Ch. 10 - For a flow rate of 12 L/s and turbine speed of 65...Ch. 10 - The velocity of the water jet driving this impulse...Ch. 10 - An impulse turbine is to develop 15 MW from a...Ch. 10 - An impulse turbine under a net head of 33 ft was...Ch. 10 - The absolute velocities and directions of the jets...Ch. 10 - A fanboat in the Florida Everglades is powered by...Ch. 10 - A jet-propelled aircraft traveling at 225 m/s...Ch. 10 - When an air jet of 1-in.-diameter strikes a series...Ch. 10 - The volume flow rate through the propeller of an...Ch. 10 - A typical American multi blade farm windmill has D...Ch. 10 - An airplane flies at 200 km/h through still air of...Ch. 10 - This ducted propeller unit drives a ship through...Ch. 10 - A model of an American multi blade farm windmill...Ch. 10 - A large Darrieus vertical axis wind turbine was...Ch. 10 - Show that this ducted propeller system when moving...Ch. 10 - This ducted propeller unit (now operating as a...Ch. 10 - What is the maximum power that can be expected...Ch. 10 - If an ideal windmill is operating at best...Ch. 10 - A prototype air compressor with a compression...Ch. 10 - Prob. 89PCh. 10 - We have seen many examples in Chapter 7 of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The engine is connected to a dynamometer which gives a brake output torque of 200 N-m at 3600 RPM. At this speed air enters the cylinders at 85 kPa and 60°C and the mechanical efficiency of the engine is 80%. Find out power lost in friction. Assume necessary data which is not given in question. Vd = .002 m3 B = .08 marrow_forwardThe compressor of a jet engine tested at sea level on a stationary test bed on a day when the atmospheric temperature and pressure is 298 K and 101kPa, respectively. When running at its design operating point, the masss flow rate through the compressor is measured as 15 kg/s and the rational speed is 6200 rpm. Determine the mass flow rate and the rational speed when the compressor is operating at the design operating point during high altitude cruise with an onlet stagnation temperature of 236 K and an inlet stagnation pressure of 10.2 kpa. The design pressure ratio of compressor is 20. If the compressor isentropic efficiency is determined from the test to be 85=, calculate the power input at the cruise condition. Assume for air that y=1. 4 and Cp=1005 kJ/kg-K throughout.arrow_forwardFor a maximum temperature of 1650 and 1800 K at pressure ratios in the compressor of 12, 15, 20 and 25:1 calculate the thrust, propulsive efficiency and the specific thrust. Present and discuss the results.arrow_forward
- A single-stage, single-acting air compressor with runs at 600 r/min. It has a polytropic index of 1.26. The induced volume flow rate is 0.72 m3/min and the air must be delivered at 660 kPa. The free air conditions are 101.3 kPa and 15 0C. The clearance volume is 6% of the stroke volume and the stroke/bore ratio is 1.49/1. Calculate the bore of the piston in meter to 4 decimal places.arrow_forwardQUESTION2 A single-stage double-acting air compressor delivers air at 7.5bar. The pressure and temperature at the end of suction stroke are 1bar and 25°C. It delivers 2.2m3 of free air per minute when the compressor is running at 310rev/min. The clearance volume is 5% of stroke volume. The pressure and temperature of ambient air are 1.03bar and 20°C. Take: index of compression = 1.25 and index of expansion = 1.3. %3D %3D Determine: 2.1 volumetric efficiency of the compressor; 2.2 diameter and stroke of the cylinder if both are equal; 2.3 indicated power of the compressor and Brake power (B.P.) if the mechanical efficiency is 85%. 2.4 Draw the P-V diagram will all the relevant information.arrow_forwardThe pressure gauge at a micro-hydro powerhouse shows a reading of 500KN/m?. The velocity head inside the pipe can be neglected. The 2-jet Pelton wheel is having a diameter of 0.58m. The two nozzles cause a total loss of 2% of their inlet head. At rated water flow rate, the diameter of each jet of water is 2cm. The efficiency of the turbine at the rated speed of 520 rpm is 85%. The density of water is 1000 kg/m3 and gravitation constant is 9.81m/s?. (a) Determine under rated operating condition, (i) Net head available to the turbine (ii) Velocity of water jets (iii) Water flow rate to the turbine (iv) Mechanical power outputarrow_forward
- In a single-acting two-stage reciprocating air compressor, 4.5 kg of air per min are compressed from 1.013 bar and 15°C through a pressure ratio of 9 to 1. Both stages have the same pressure ratio and PV=constant. Assume that the clearance volume of both stages is 5% of their respective swept volumes and that the compressor runs at 300 rev/min. Evaluate; (i) the indicated power; and (ii) the cylinder swept volumes required.arrow_forwardA single-stage, single-acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1.26. The induced volume flow rate is 0.72 cubic meters per min and the air must be delivered at a pressure of 660 kPa. The free air conditions are 101.3 kPa and 15 °C. The clearance volume is 6.1% of the stroke volume and the stroke/bore ratio is 1.6/1. Calculate the volumetric efficiency in fraction to 3 decimal places. Please ignore this line, its for system calculation 1, 100, 0.77, 664 Do not add unit.arrow_forwardA single-stage, single-acting air compressor with runs at speed 600 rpm. It has a polytropic index of 1.26. The induced volume flow rate is 0.94 cubic meters per min and the air must be delivered at a pressure of 660 kPa. The free air conditions are 101.3 kPa and 15°C. The clearance volume is 6% of the stroke volume and the stroke/bore ratio is 1.6/1. 1. Calculate the delivery air temperature (in °C) 2. The volume of air induced into the compressor is ____ m3arrow_forward
- The performance characteristics of a certain centrifugal pump are determined from anexperimental setup shown in the figure. When the flow rate of a liquid (SG= 0.9) through thepump is 120 gpm, the pressure gage at (1) indicates a vacuum of 95 mm of mercury and thepressure gage at (2) indicates a pressure of 80 kPa. The diameter of the pipe at the inlet is110 mm and at the exit it is 55 mm.If Z2-Z1= 0.5 m, what is the actualhead rise across the pump? Explainhow you would estimate the pumpmotor power requirement.arrow_forwardcentrifugal compressor has pressure ratio of 4:1 with an isentropic efficiency of 80% when running at 15000 rpm and inducting air of 293° K. Curved vanes at inlet given the air a pre whirl of 25° to the axial direction curved vanes at inlet given the air a pre whirl of 25° to the axial direction at all radil and mean dia of eye is 250 mm. The absolute air velocity at inlet is 150 m/sec. Impellér tip dla 600 mm calculate sliparrow_forwardAnswer the followwing problem: Determine the number of stages needed for a centrifugal pump if it is used to deliver 600gal/min of water and pump power of 15Hp. Each impeller develops head of 38ft. Calculate the compressor work in kJ required to compress 1 kg of an ideal gas from an initial volume and pressure of 0.65m3 and 101.3kpa to a final pressure of 517kpa & volume of 0.1943m3.ANS. 133.549 An air compressor takes air at 97kpa at the rate of 0.4m3/s and discharges to 650kpa. If power input to the compressor is 110kw, determine the heat loss(kw) in the compressor. ANS. 11.948arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license