A9 cm diameter solid aluminum post is subjected to a horizontal force of V=8.5 kN and a concentrated torque of T=8.8 kNm, acting in the directions shown in the figure below. Assume that L= 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. <

A9 cm diameter solid aluminum post is subjected to a horizontal force of V=8.5 kN and a concentrated torque of T=8.8 kNm, acting in the directions shown in the figure below. Assume that L= 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. <

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 597 587 567 O O O
A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a concentrated torque of T = 7.5 kNm, acting in the directions shown in the figure below. Assume that L = 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places.
The stress components acting on an infinitesimal element extracted from a plate subjected to the plane stress state are given in the figure. a) Find the principal normal stresses and their directions and show them on the oriented element. b) Draw the Mohr circle schematically and indicate the points on the given element on this circle. 60MPA A 30° 60° 40MPA 80MPA
50 MPа 60 100 MPa For the stress conditions given in the figure; a) Draw the Mohr Circle. b) Find the principal stress values and their directions and show them on the figure. c) Find the normal and shear stresses on the C plane and show the point corresponding to this plane on the Mohr circle.
Please solve all. Both Questions Please.
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)
Please Give detailed Solutions and Correct Answers.Solve the problems below : (Use 4 decimal places for all your computations )
The AB part of the rod is steel and is 100mm in diameter.The BC part of the rod is copper and its diameter is 80 mm. a)Draw the normal force diagram of the rod. b)Calculate the normal stresses in sections AB and BC. c)Calculation of the total length change of the bar.
6. A steel bar with an ultimate strength of 1110 MPa is carrying a 305.8104- metric ton load, F. It is attached to a support by a rectangular steel pin with a known cross-sectional dimension of 1 = 11 in. What is the unknown cross- sectional dimension, w (in inches), if the bearing stress is 9.68703 ksi and the shearing stress is 3.07869 ksi in the pin? What is the shear stress in the pin (in kPa) if the modulus of elasticity of steel is 200 GPa? F Rectangular Cross Section