The state of in-plane stress at a point on an element of material is shown. Let a₂ = 55.0 ksi, ay = 16.0 ksi and Tay = 10.0 ksi Use this information to represent the state of stress of the same point that is rotated through an angle of 0-35° ▼ Part A - Normal and shear stress on element sectioned at plane a-a Using the element sectioned at plane a-a and the rotated coordinate system shown, determine the normal and shear stresses, and Try, respectively, acting on plane a-a CO Part B - Normal and shear stress on element sectioned at plane b-b Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b Express your answers in ksi to three significant figures separated by a comma. View Available Hint(s) ON TH IVE ΑΣΦ| it | vec| 4 ? ksi

The state of in-plane stress at a point on an element of material is shown. Let a₂ = 55.0 ksi, ay = 16.0 ksi and Tay = 10.0 ksi Use this information to represent the state of stress of the same point that is rotated through an angle of 0-35° ▼ Part A - Normal and shear stress on element sectioned at plane a-a Using the element sectioned at plane a-a and the rotated coordinate system shown, determine the normal and shear stresses, and Try, respectively, acting on plane a-a CO Part B - Normal and shear stress on element sectioned at plane b-b Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b Express your answers in ksi to three significant figures separated by a comma. View Available Hint(s) ON TH IVE ΑΣΦ| it | vec| 4 ? ksi

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

4 of 11 Plane-Stress Transformation Learning Goal: The state of in-plane stress at a point on an element of material is shown. Let |ox| = 320 MPa, |oy| = 120 MPa, and |Txy| = 75.0 MPa. Use this information to represent the state of stress of the same point that is rotated through an angle of 0 = 25.0°. b Txy σx Part A - Normal and shear stress on element sectioned at plane a-a Using the element sectioned at plane a-a and the rotated coordinate system shown, determine the normal and shear stresses, σ and Ta'y', respectively, acting on plane a-a. 90-0 -90-8 X Express your answers in MPa to three significant figures separated by a comma. 0
Mechanical Advantage Classwork Directions: Show all work with the following steps... 1.Write the equation. 2.Fill in the equation. 3.Solve. To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. An Effort force of 30N is applied to a screwdriver to pry the lid off of a can of paint. The screwdriver applies 90N of force to the lid. What is the MA of the screwdriver? 1. MA =
Simple Machines-Levers, Inclined Planes, and Pulleys Directions: Use the appropriate equation to answer the following questions. All answers should be recorded below or in your Engineering Design journal. Remember to show all work. A lever has an effort arm that is 5 meters long and a resistance (load) arm that is 3.5 meters long. How much effort is needed to lift a 100 Newton weight? 5K i). Draw the figure representing the problem ii). How much effort is needed to lift a 100 Newton weight? iii). What is the Actual Mechanical Advantage 1. 5m i) AOON 5-5m
Manual Calculation 2: Refer to image shown. Decimal Places: 2 Use hand calculations, modeling is not necessary The "Shaft" carries a torque that induces a shear force in the "Bolts". Shear Stress in the 4 bolts (kN/m³) S = 40,000 "Bolt" spacing (m) C = 0.24 "Bolt" diameter (mm) d = 30 "Shaft" diameter (m) D = 0.15. Assume each "Bolt" carries the same shear force. What is the Torque (kN-m) carrying capacity of the shaft? 4 Typ (d) Bolt Shaft
Question: In a forming process the length of material changes from 50 mm to 60 mm. Show the maximum true stress value on the graph (True Stress vs. True Strain) plotted in Excel Program or any plotting program not by hand using the flow stress equation given below. o = Kɛ" Where the parameters are o: True Stress in MPa K: Strength Coefficient, K = (200 + N) in MPa, N is Your Rank Number in the Class List ɛ : True Strain, s = In ('/1,) n: Strain Hardening Exponent, n = 0.27 Notes: - Never change the template and only write your own identity data. - Your N value is 1 - Take at least 3 digits after the decimal point. - Specify the units. - You can use Excel or any plotting program not by hand then paste your graph into then solution section.
Answer and solve the following problem.
Recall that muscle generates force at 30 N/cm?. Two cross sections are taken from the rectus femoris muscle (bipennate muscle similar to the diagram below). The length and width of the first cross section is 6 cm and 5 cm respectively with a 35° angle of pennation. The length and width of the second cross section is 5.6 cm and 3 cm respectively with a 31° angle of pennation. What is the predicted maximum tendon force (FTendon) of this muscle in Newtons? Answer to the nearest 0.1 N. Freodas
1. Note: for part a), you can do this without a calculator; it might be easier to work out the problem symbolically, and then substitute the numbers at the end of the problem. В 2L The axial rod is fixed to the two walls, as shown above. Portion AB is composed of one material (EAB = E), while portion BD is composed of a different material (EBD = 2E). Portion AB has cross sectional area AAB = A, while portion BD has cross sectional area ABD = 2A. EAB = E = 15×106 psi AAB = A = 1 in² EBD = 2E = 30×10° psi ABD = 2A = 2 in² LAB = L = 10 in. LBC = 2L = 20 in. LcD = L = 10 in. An external force, P = 100 kips, is applied at point C as shown below. a) Determine the reaction forces at wall A and D, Ra and Rp. Specify the direction, (→) or (+). b) Deflection at point C. Specify the direction, (→) or (+). (Ans: RA = 100/7 kips →, Rp = 600/7 kips →, & = 1.429x10² in –)
or: Oy ay: Txy I The figure (not drawn to scale) shows a state of stress in a xy frame of reference. We wish to calculate the state of stress in the rotated frame of reference x'y'. Given Angle of rotation 0 = -33°, direct stresses o = -20 MPa and oy = 0 MPa, shear stress Tay = -10 MPa calculate the state of stress in the rotated frame of reference. Enter your answers in the boxes below. The inswers are cceptable within a tolerance of 1 MPa. MPa (2 mark) MPa (2 mark) Ox MPa (2 mark) X' X X
The plot below of load vs. extension was obtained using a specimen (shown in the following figure) of an alloy remarkably similar to the aluminum-killed steel found in automotive fenders, hoods, etc. The crosshead speed, v, was 3.3x104 inch/second. The extension was measured using a 2" extensometer as shown (G). Eight points on the plastic part of the curve have been digitized for you. Use these points to help answer the following questions. 1. 900 800 (0.10, 630 ) 700 (0.50, 745) (0.30, 729) 600 (0.20, 699) (0.40, 741.5) 500- (0.004, 458) (0.80, 440 ) - 400 (0.0018, 405) 300 D= 3.3 " 0.03" 200 G=2.0" 100 - 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Extension, inches a. Determine the following quamtities. Do not neglect to include proper units in your answer. Young's Modulus Total elongation Yield stress Ultimate tensile strength Uniform elongation Engineering strain rate Post-uniform elongation b. Construct a table with the following headings, left-to-right: Extension, load, engineering strain,…
Solve it correctly please. Show all steps. I
Convert 22C to Fahrenheit.