A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.

A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 13R: Find the volume of the following: a. 5 cube b. 10 of 8 pipe

See similar textbooks

Similar questions

A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 360.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.30 MN. pressure vessel W bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. cm x10 X
A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at 20°C (68°F) through 1750 ft of horizontal pipe with an exit pressure at 20 psig. The pressure drop is approximately -280 psig. Estimate the pipe diameter (in inches) that will result in the given pressure drop. For water at 68°F: p = 1.94 slug/(ft^3), and u = 2.09E-5 slug/(ft-s). Round your answer to 2 decimal places.
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your answer should have 0 decimal places needed. Ex: 76,440 10 - 30 B
A frozen hot dog at -32 degrees Fahrenheit is placed in a room at 70 degrees. After 15 minutes, the temperature of the hot dog is 30 degrees. (a) Find the value for k in Newton's Law of Cooling. Round your answer to the nearest thousandth. k = (b) What will the temperature of the hot dog be after 45 minutes? Round your answer to the nearest degree. degrees Fahrenheit (c) How long will it take for the hot dog to reach 60 degrees? Round your answer to the nearest minute. minutes 2 Calculator Submit Question P Type here to search esc %23 3. 近

Find the volume of the following: a. 5 cube b. 10 of 8 pipe
Solve 0.782bar in p/q form
The wind chill (i.e. how cold it actually feels) is given by W(T,v) = 35.74 +0.6215T – 35.75v0.16 + 0.4275Tv0.16 degrees Fahrenheit when the actual air temperature is T degrees Fahrenheit and the wind speed is v miles per hour. Enter the function into your Y1 and verify that W(-5,15) = -25.80216395. Ploti Plot2 Plot3 1 -25.80216395 Y1835.74+0.6215T=5 T-35.75V0.16+0. V=151 4275TV6. 1Ği bound=(-1e99,1. Ýs= Use this function to answer questions 1 - 8.
a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the maximum allowable stress in the pipe is 7.5 x 109 N/m2 , calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places. b)A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2 to 2 decimal places.
answer asap plz
Consider a 146 ft long, 4 in. type M copper tubing. What is the outside diameter in inches? (Round your answer to at least three decimal places.) in. What is the inside diameter in inches? (Round your answer to at least three decimal places.) in. What is the length in inches? in. What is the formula for the volume of a cylinder? (Use the following as necessary: h for the height and R for the radius. Do not substitute numerical values; use variables only.) V = What is the volume of the outer cylindrical shape in in.3? in.3 What is the volume of the inner cavity (in in.3)? in.3 What is the volume of the tubing? (Use the following as necessary: Vouter and Vinner. Do not substitute numerical values; use variables only.) V = What is the volume of the tubing in in.3? in.3 What is the volume of tubing in ft3? ft3
1. If water is cooled from 50OC to -5OC, what is the temperature change on the Celsius, Fahrenheit and Rankine scales? Note: Draw the figure of a thermometer reflecting the given temperatures. Write the formula and solve for the required quantity. Encircle or box the final answer/s.
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.