3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques shown in the figure. If Tc = 250 lb- ft, determine the max- imum shear stress developed in each material. The moduli of rigidity for steel, alu- minum, and bronze are 12 × 10° psi, 4 × 10° psi, and 6 × 10° psi, respectively. %3D 500 lb · ft | Steel 1.0 in. Aluminum | 2 in. Bronze $1.0 in. B D 6 ft 4 ft – 3 ft –

3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques shown in the figure. If Tc = 250 lb- ft, determine the max- imum shear stress developed in each material. The moduli of rigidity for steel, alu- minum, and bronze are 12 × 10° psi, 4 × 10° psi, and 6 × 10° psi, respectively. %3D 500 lb · ft | Steel 1.0 in. Aluminum | 2 in. Bronze $1.0 in. B D 6 ft 4 ft – 3 ft –

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.30 A solid steel shaft transmits 20 hp while running at 120 rev/min. Find the smallest safe diameter of the shaft if the shear stress is limited to 5000 psi and the angle of twist of the shaft is not to exceed 9° in a length of 10 ft. Use G= 12 x 106 psi for steel.
Please solve it..
Q/ For the shaft shown in the figure below, find: Maximum torsional stress in part AB, Let E = 200 GPa, G 80 GPa and a = 12 x 10° 1/°C. a B. T, T, d, a, b and 4T are given in the table below. T2 (mm) (N.m) T (N.m) AT b a d (°C) (mm) (mm) 35 300 280 40 420 350
A step shaft (shown to the right) is sub- jected to a torque, T (not shown). The shaft is made of copper. Use a factor of safety of 2.0 (and t y) and take into account the stress concentration due to the change in diameter of the shaft. 0.75 1/16" radius 0.35" Determine the maximum allowable torque T that may be applied. 9.13 lb-in.
A steel shaft with a diameter 1.95 inches and length 4.35 feet transmits 80 HP from an electric motor to a compressor. The allowable shear stress is 8,600 psi and the allowable angle of twist is 2.15 degrees. G=12 x 10^6 psi Determine the polar moment of inertia (in in^4) of the steel shaft. Determine the required torque (in lb-in) as limited by stress. Determine the required torque (in lb-in) as limited by the angle of twist. Determine the minimum allowable speed of rotation (in rpm).
4 m www.muthalinc.com Q3. The shaft shown in Fig.3 is carries R1 Figure P-68R=15 R=15cm two pulleys each weighs 400 N. The allowable shear and normal stresses are 56 and 84 MPa, respectively. The ratio of the belt tension are as shown in the B. 2F Fig. Determine the maximum permissible value of the shaft diameter if the belt 40 cm 100 cm 40 cm tension if the shaft transimit power 10KW with 1000 r.p.m...
A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc i B (2) b Tc (3) Tp lb-ft D
B5
A shaft is required to transmit 1 MW power at 240 r.p.m. The shaft must not twist more than 1 degree on a length of 15 diameters. If the modulus of rigidity for material of the shaft is 80 GPa, find the MPa] diameter of the shaft and shear stress induced.
The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 81kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case. T T' Figure Q2(c)
Mechanics of deformable bodies
Problem 2. A 300-mm diameter solid disk is to be used as a flywheel in a machine to reduce speed fluctuations. If the disk material has yield strength S Y =720 MPa, density p=7000 kg/m^ 3 . and Poisson's ratio J = 0.2 ^ c , find the maximum allowable rotational speed (in rpm) for a safety factor of 1. a) Solve using the MSST. b) Solve assuming that the disk is mad of cast iron having Sut = 207MPa , Fuc = 780MPa, p = 7000 kg/m³, and Poisson's ratio v r = 0.26 , Use Coulomb-Mohr theory.