3-a. Determine the ditribution of shear stress in the following circular shafts that are subject to amaximum torque of 7.5 Nm by calculating the polar second moment of area.a)b)a)Ob)Ob. Using the previous answers; determine the angular deflection in both shafts. Both shafts are20 cm long and the modulus of rigidity for the material is 60GN/m^2.ORRORR = 5mmr = 3mmR = 5mmr = 3mm

Given : The outer radius is The inner radius is The torque is The modulus of rigidity is The length…

a. Determine the ditribution of shear stress in the following circular shafts that are subject to a maximum torque of 7.5 Nm by calculating the polar second moment of area. a) b) a) O b) R O b. Using the previous answers; determine the angular deflection in both shafts. Both shafts are 20 cm long and the modulus of rigidity for the material is 60GN/m^2. ( D R R = 5mm r = 3mm O R = 5mm r = 3mm

a. Determine the ditribution of shear stress in the following circular shafts that are subject to a maximum torque of 7.5 Nm by calculating the polar second moment of area. a) b) a) O b) R O b. Using the previous answers; determine the angular deflection in both shafts. Both shafts are 20 cm long and the modulus of rigidity for the material is 60GN/m^2. ( D R R = 5mm r = 3mm O R = 5mm r = 3mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q) A shaft 1.5 m long are supported in flexible bearings at the ends and carry two wheels each of 50 kg mass. One wheel is situated at the center of the shaft and the other at a distance of 0.4 m from the center towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young's modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.
5) Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value of all shafts is same (50 mm) and material is steel (G-85 GPa) Dimensions in mm 40 500 Nm
Problem 2. A 300-mm diameter solid disk is to be used as a flywheel in a machine to reduce speed fluctuations. If the disk material has yield strength S Y =720 MPa, density p=7000 kg/m^ 3 . and Poisson's ratio J = 0.2 ^ c , find the maximum allowable rotational speed (in rpm) for a safety factor of 1. a) Solve using the MSST. b) Solve assuming that the disk is mad of cast iron having Sut = 207MPa , Fuc = 780MPa, p = 7000 kg/m³, and Poisson's ratio v r = 0.26 , Use Coulomb-Mohr theory.
A shaft is subjected to a torque of 28 kNm and a maximum bending moment of 25 kNm. The shaft is solid with a diameter of 125 mm. Using the Mohr circle method find the values for the principal stresses and themaximum shear stresses on the shaft i)Construct the Mohr circle on the graph paper provided. ii) Using the Mohr circle method find the values for the principal stresses and the maximum shear stresses on the shaft.iii) Show the orientations of the planes on which the principal stresses act on a rotatedelement
A steel shaft in the form of a solid body circular rod or a circular tubecan be manufactured. The shaft is required to bear 1200 N.m of torsional torque. Anti-shear stress for shaft material 40 MPa, largest permissible unit torsion angle in the rod 0.75 ^ 0As / m and steel's shear modulus is G = 78 GPa;a) Find the required diameter d0 for a solid circular shaft.b) Find the required outer diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and the weight ratio for ring cross section and solid section shafts. please solve carefully and in detail thank you
What is the polar moment of inertia of a solid steel shaft in mm^4 that will not twist through more than 2 degree in a 8 meter length when subjected to a torque of 22 kN.m? G = 83 GPa.
1) Consider a hollow shaft. A torque T is applied to this shaft and the resistance to the applied torque due to r, is 2T/3. It is desired to reduce this resistance to T/3 by changing the inner radius r, while keeping outer radius r₂ constant. Calculate the ratio of initial and final dimensions of radius r₁.
A 4m solid core steel shaft with 50 mm diameter is fixed at its ends. It is subjected to a 400 N-m torque 1m from the left end and a 100 N-m torque 0.5 m from the right end (same direction). a) Determine the reactions at the ends. b) Determine the maximum shear stress in the shaft. c) If the shaft is hollow core and the maximum allowable shear stress in the shaft is 37 MPa, determine the thickness of the shaft given that the outside diameter is still 50 mm.
Q.10 According to a stiffness based design, a solid shaft has a diameter 50mm and the shear modulus of the material of the shaft is 35GPA. Find out the Torsional rigidity. A 21.475 kNm' B 22.897kNm² C 65 kNm2 D 56KPA
Two solid circular shafts are connected through a flange bolt coupling consisting of 3 circular bolt rows. The free ends of the shafts are to be subjected by equal torque. Solid Shafts Diameter (mm) Length (m) Shear Modulus (GPa) Shaft A Shaft B 65 66 3 3.8 81 84.6 Flange-bolt coupling Bolt Circle Diameter (mm) Bolt Alowable Shear Stress (MPa) Bolt Diameter Shear Modulus Number of Bolt Row (mm) (GPa) Bolts 1 95 14 77 35 4 2 116 17 97 42 10 3 135 13 93 49 14 A Calculate the torque capacity of the flange-bolt coupling (kN-m). B. Calculate the stresses in both shaft if the torque capacity is applied at both ends (MPa). C. Calculate the total angle of twist (in degrees).
A steel shaft can be manufactured as a circular rod with a solid body or a circular tube. The shaft is required to bear a torsion moment of 1200 N.m. The shear safety stress for the shaft material is 40 MPa, the largest permitted unit torsion angle in the bar is 0.75º/m. The shear modulus of steel is G=78 GPa. a) Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a ring-section shaft with a thickness in tenths of the outer diameter. c) Find the diameter ratio (d2/d0 ratio) and the weight ratio for ring cross section and solid section shafts.
What is the polar moment of inertia of a solid steel shaft in mm^4 that will not twist through more than 2^0 in a 6 meter length when subjected to a torque of 44 kN.m? G = 83 GPa.