Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 9, Problem 9.18P
(a)
To determine
The elastic modulus of polymer.
(b)
To determine
The viscosity of new polymer.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A single crystal of a metal is oriented for a tensile test such that its slip plane normal makes an angle of 64.0° with the tensile axis.
Three possible slip directions make angles of 30°, 48°, and 78° with the same tensile axis.
(a) Which of these three slip directions is most favored?
i
(b) If plastic deformation begins at a tensile stress of 1.3 MPa (188.6 psi), determine the critical resolved shear stress for this metal.
i
MPа
A copper rod is deformed using a uniaxial tensile force of 16000 N. Deformation continues until sufficient strain hardening has occurred such that the applied force is too small to allow further deformation. After deformation, the rod has a diameter of 0.01 m and a length of 1.5 m. Assume that copper follows the strain hardening lawwith K of 310 MPa and n=0.54
Please calculate the true strain after the deformation ?
A cylindrical polymer with a diameter of 10nm when stress is applied to it and a change in
diameter of 0.0025nm is equal. If you know that the polymer is completely elastic and the
modulus of elasticity is 97Gps, what is the amount of elongation in the direction of the x-axis
Chapter 9 Solutions
Materials Science And Engineering Properties
Ch. 9 - Prob. 1CQCh. 9 - Prob. 2CQCh. 9 - Prob. 3CQCh. 9 - Prob. 4CQCh. 9 - Prob. 5CQCh. 9 - Prob. 6CQCh. 9 - Prob. 7CQCh. 9 - Prob. 8CQCh. 9 - Prob. 9CQCh. 9 - Prob. 10CQ
Ch. 9 - Prob. 11CQCh. 9 - Prob. 12CQCh. 9 - Prob. 13CQCh. 9 - At temperatures above the equi-cohesive...Ch. 9 - Prob. 15CQCh. 9 - Prob. 16CQCh. 9 - Prob. 17CQCh. 9 - Prob. 18CQCh. 9 - Prob. 19CQCh. 9 - Prob. 20CQCh. 9 - Prob. 21CQCh. 9 - Prob. 22CQCh. 9 - Prob. 23CQCh. 9 - Prob. 24CQCh. 9 - Prob. 25CQCh. 9 - Prob. 26CQCh. 9 - Prob. 27CQCh. 9 - Prob. 28CQCh. 9 - Prob. 29CQCh. 9 - Prob. 30CQCh. 9 - Prob. 31CQCh. 9 - Prob. 32CQCh. 9 - Prob. 33CQCh. 9 - Prob. 34CQCh. 9 - Prob. 35CQCh. 9 - Prob. 1ETSQCh. 9 - Prob. 2ETSQCh. 9 - Prob. 3ETSQCh. 9 - Prob. 4ETSQCh. 9 - Prob. 5ETSQCh. 9 - Prob. 6ETSQCh. 9 - Prob. 7ETSQCh. 9 - Prob. 8ETSQCh. 9 - Prob. 9ETSQCh. 9 - Prob. 10ETSQCh. 9 - Prob. 11ETSQCh. 9 - Prob. 12ETSQCh. 9 - Prob. 9.1PCh. 9 - Prob. 9.2PCh. 9 - Prob. 9.3PCh. 9 - Prob. 9.4PCh. 9 - Prob. 9.5PCh. 9 - Prob. 9.6PCh. 9 - Prob. 9.7PCh. 9 - Prob. 9.8PCh. 9 - Prob. 9.9PCh. 9 - Prob. 9.10PCh. 9 - For silver at a tensile stress of 7 MPa and a...Ch. 9 - For germanium at a tensile stress of 410 MPa and a...Ch. 9 - Prob. 9.13PCh. 9 - Prob. 9.14PCh. 9 - Prob. 9.15PCh. 9 - Prob. 9.16PCh. 9 - Prob. 9.17PCh. 9 - Prob. 9.18PCh. 9 - Prob. 9.19PCh. 9 - Prob. 9.20PCh. 9 - Prob. 9.21PCh. 9 - Prob. 9.22P
Knowledge Booster
Similar questions
- A steel plate used for polymer forming is to be bent into a circular shape having an inside radius of 10 m. What maximum thickness can be used for the plate if the normal stress is not to exceed 267 MPa? Assume that the modulus of elasticity for the steel is 201 GPa.arrow_forward2. A polymer muterial is subjected to a constant load for a set amount of time and then the load is removed. This experiment generates the stress versas time plot and the strain versus time plot shown below. Describe what is happening to the material at following locations on the strain versus time plot below: • At point A • Between point A and point B • Between point B and peint C • Between point C and peint D Briefly comment on how you would expect this strain versus time plot to change if the experiment was carried out en anather sample of the same polymer at a temperature below the polyrmer's glass transition temperature. Time, t в A D Time, t Strain, ɛ Stress, oarrow_forwardThe stress-strain curve for a metal is plotted as shown in Figure Q1 (a). On the graph,show the yield point, fracture point, proportional limit and ultimate pointarrow_forward
- Two triangular wedges are glued together as shown in the figure. The stress acting normal to the interface, o, is MPa. 100 MPa 100 MPa on 45% 100 MPa -100 MPaarrow_forwardWhat is the modulus of resilience for the material with the stress-strain behavior given in the figure belowarrow_forwardA metal sample on a tension in the test ,296MPa , a tensile true strain 0.08, and true stress 356 MPa when the strain is 0.27. Determine the strength coefficient and strain hardening exponent in the flow curve equation.arrow_forward
- The stress–strain relation shown in Figure was obtained during the tensile test of an aluminum alloy specimen. Determine the Yield stress using an offset of 0.002 strain.arrow_forwardTime len A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T) of this material. given that S1=195 Mpa; S2=243.75 Mpa; El=0.19; E2=0.38 E1 Strain E2 Stress - Strain diagram of a metal alloy OA.T= 18.52 Mpa O B.T= 92.62 Mpa O C.T= 37.05 Mpa O D.T= 60.21 Mpa Stress (Mpa) 3arrow_forwardA thin cylinder of internal diameter 1 m and thickness 0.02 m contains a gas. The tensile stress in the material is not to exceed 100 MPa then determine the internal pressure of the gasarrow_forward
- The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is initially free, determine the temperature change that will cause a tensile stress of 60 Mpa in the steel rod.arrow_forwardDraw a tensile stress-strain curve for a typical semi-crystalline polymer such as LLDPE, and define the three main regions on the curve.arrow_forwardA steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning