Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 9, Problem 9.17P
To determine
The total strain after 30 days in material.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A brass wire of diameter d = 2.33 mm is stretched tightly between rigid supports so that the tensile force is T = 93 N (see figure).
T
The coefficient of thermal expansion for the wire is 19.5 x 106/°c, and the modulus of elasticity is E = 110 GPa.
(a) What is the maximum permissible temperature drop (in °C) if the allowable shear stress in the wire is 60 MPa? (Enter the magnitude.)
°C
(b) At what temperature change (in °C) does the wire go slack?
°C
During a creep test (constant stress equal to 3.5 MPa) a material has an initial strain of
10 and a strain of 2 x 10* after 30 days. The same material was also submitted to a
relaxation test (constant strain equal to 1.5 x 104). During the relaxation test, determine the
stress after 30 days. Assume that the material follows the Maxwell model.
4
X
Time len
A material has the stress-strain behavior shown in the Figure below. Calculate the toughness (T) of
this material. given that S1=195 Mpa; S2=243.75 Mpa; El=0.19; E2=0.38
E1
Strain
E2
Stress - Strain diagram of a metal alloy
OA.T= 18.52 Mpa
O B.T= 92.62 Mpa
O C.T= 37.05 Mpa
O D.T= 60.21 Mpa
Stress (Mpa) 3
Chapter 9 Solutions
Materials Science And Engineering Properties
Ch. 9 - Prob. 1CQCh. 9 - Prob. 2CQCh. 9 - Prob. 3CQCh. 9 - Prob. 4CQCh. 9 - Prob. 5CQCh. 9 - Prob. 6CQCh. 9 - Prob. 7CQCh. 9 - Prob. 8CQCh. 9 - Prob. 9CQCh. 9 - Prob. 10CQ
Ch. 9 - Prob. 11CQCh. 9 - Prob. 12CQCh. 9 - Prob. 13CQCh. 9 - At temperatures above the equi-cohesive...Ch. 9 - Prob. 15CQCh. 9 - Prob. 16CQCh. 9 - Prob. 17CQCh. 9 - Prob. 18CQCh. 9 - Prob. 19CQCh. 9 - Prob. 20CQCh. 9 - Prob. 21CQCh. 9 - Prob. 22CQCh. 9 - Prob. 23CQCh. 9 - Prob. 24CQCh. 9 - Prob. 25CQCh. 9 - Prob. 26CQCh. 9 - Prob. 27CQCh. 9 - Prob. 28CQCh. 9 - Prob. 29CQCh. 9 - Prob. 30CQCh. 9 - Prob. 31CQCh. 9 - Prob. 32CQCh. 9 - Prob. 33CQCh. 9 - Prob. 34CQCh. 9 - Prob. 35CQCh. 9 - Prob. 1ETSQCh. 9 - Prob. 2ETSQCh. 9 - Prob. 3ETSQCh. 9 - Prob. 4ETSQCh. 9 - Prob. 5ETSQCh. 9 - Prob. 6ETSQCh. 9 - Prob. 7ETSQCh. 9 - Prob. 8ETSQCh. 9 - Prob. 9ETSQCh. 9 - Prob. 10ETSQCh. 9 - Prob. 11ETSQCh. 9 - Prob. 12ETSQCh. 9 - Prob. 9.1PCh. 9 - Prob. 9.2PCh. 9 - Prob. 9.3PCh. 9 - Prob. 9.4PCh. 9 - Prob. 9.5PCh. 9 - Prob. 9.6PCh. 9 - Prob. 9.7PCh. 9 - Prob. 9.8PCh. 9 - Prob. 9.9PCh. 9 - Prob. 9.10PCh. 9 - For silver at a tensile stress of 7 MPa and a...Ch. 9 - For germanium at a tensile stress of 410 MPa and a...Ch. 9 - Prob. 9.13PCh. 9 - Prob. 9.14PCh. 9 - Prob. 9.15PCh. 9 - Prob. 9.16PCh. 9 - Prob. 9.17PCh. 9 - Prob. 9.18PCh. 9 - Prob. 9.19PCh. 9 - Prob. 9.20PCh. 9 - Prob. 9.21PCh. 9 - Prob. 9.22P
Knowledge Booster
Similar questions
- A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by 50°C. If rod is allowed to expand by 14 mm, what will be the stress induced in rod? Take E = 200 GPa and a = 12 × 10-6/°C. (a) 20 MPa (c) 68 MPa (b) 35 MPa (d) None of thesearrow_forwardCreep exercises You are involved in a design for high temperature alloys and have performed a rupture test of material A and B. After data analysis, you noticed that the master curve (o vs LMP) of both material A and B coincide as shown in the diagram below. Based on the rupture strength o (MPa) AtB LMP = T(C+ Int) Which material will you select if they both have same constant (CA= CB)? Which material will you select if C < C? Motivate your answer by means of a calculation.arrow_forwardA steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mmarrow_forward
- The composite bar of neglible mass is connected to two rods as shown in the figure. If the system is initially free, determine the temperature change that will cause a tensile stress of 60 Mpa in the steel rod.arrow_forwardA 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 33 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: €, =710 με and ε,--255 με (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 24 kN, what is the modulus of elasticity for this specimen? Answers: (a) v= (b) E= GPaarrow_forwardWhat is the modulus of resilience for the material with the stress-strain behavior given in the figure belowarrow_forward
- A cylindrical specimen of a metal alloy 47.5 mm long and 9.72 mm in diameter is stressed in tension. A true stress of 397 MPa causes the specimen to plastically elongate to a length of 54.3 mm. If it is known that the strain-hardening exponent for this alloy is 0.2, calculate the true stress (in MPa) necessary to plastically elongate a specimen of this same material from a length of 47.5 mm to a length of 55.8 mm. i MPaarrow_forwardThe stress–strain relation shown in Figure was obtained during the tensile test of an aluminum alloy specimen. Determine the Yield stress using an offset of 0.002 strain.arrow_forwardConsider a cylindrical metal 6 mm in diameter and 50 mm long ispulled in tension. It is known that yield strength and elastic (Young’s) Modulus of thematerial are 200 MPa and 100 GPa, respectively, and its Poisson’s Ratio is 0.3.(a) Determine whether the deformation is elastic or plastic when 6000 N is applied.(b) Calculate specimen elongation (∆l) and reduction in diameter (∆d) when 5000 N isapplied? What are the values ∆l and ∆d when the load is released?(c) If necking occurs at a load of 8850 N, determine the UTS of the metal.(d) Calculate the ductility in terms of % E.L. if the length of the specimen at fracturepoint is 56.0 mm.arrow_forward
- A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C,determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 * 10-6m/m/C. Is there a stress on the rod at 115°C?If the rod is snugly fitted against two immovable nonconducting walls at a temperature of 15°C and then heated uniformly to115°C, what is its length at 115°C? If the modulus of elasticity of steel is207 GPa, what is the stress induced in the bar? Is this stress tension or compression?arrow_forwardA solid 45 mm diameter beryllium copper (E = 131 GPa; α = 17.0 × 10−6 /°C) rod is stress free when securely attached to the unyielding supports shown in the figure below. If the compressive normal stress in the rod must not exceed 450 MPa, what is the maximum temperature increase (rounded down to the nearest degree) that can be allowed for the rod? Use L1 = 300 mm.arrow_forwardA steel bar is held by two fixed supports as shown in the figure and is subjected to an increase of temperature AT = 100°C. If the coefficient of thermal expansion and Young's modulus of elasticity of steel are 11 x 10-6/°C and 200 GPa, respectively. the magnitude of thermal stress (in MPa) induced in the bar isarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning