Statistics for Engineers and Scientists
4th Edition
ISBN: 9780073401331
Author: William Navidi Prof.
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5.3, Problem 17E
The article “Filtration Rates of the Zebra Mussel (Dreissena polymorpha) on Natural Seston from Saginaw Bay. Lake Huron“ (D. Fanslow, T. Nalepa, and G. Lang, Journal of Great Lakes Research 1995:489–500) reports measurements of the rates (in mL/mg/h) at which mussels filter seston (particulate matter suspended in seawater).
- a. In the year 1992, 5 measurements were made in the Outer Bay; these averaged 21.7 with a standard deviation of 9.4. Find a 95% confidence interval for the
mean filtration rate in the Outer Bay. - b. In the year 1992, 7 measurements were made in the Inner Bay; these averaged 8.6 with a standard deviation of 4.5. Should the Student’s t distribution be used to find a 95% confidence interval for the mean filtration rate for the Inner Bay? If so, find the confidence interval. If not, explain why not.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The article "Experimental Measurement of Radiative Heat Transfer in Gas-Solid
Suspension Flow System" (G. Han, K. Tuzla, and J. Chen, AIChe Journal, 2002:1910-
1916) discusses the calibration of a radiometer. Several measurements were made on the
electromotive force readings of the radiometer (in volts) and the radiation flux (in kilowatts
per square meter). The results (read from a graph) are presented in the following table.
Heat flux (y)
15 31 51 55 67 89
Signal output (x) 1.08 2.42 4.17 4.46 5.17 6.92
Compute the least-squares line for predicting heat flux from the signal output.
If the radiometer reads 3.00 V, predict the heat flux.
If the radiometer reads 8.00 V, should the heat flux be predicted? If so, predict it. If
not, explain why.
C.
The department of zoology at the Virginia Polytechnic Institute and State University carried out a study to determine if there is a significant difference in the density of organisms in two different stations located in Cedar Run, a secondary river that is located in the river basin. Roanoke. Drainage from a sewage treatment plant and overflow from the Federal Mogul Corporation sedimentation pond enter the flow near the source of the river. The following data give the density measurements, in numbers of organisms per square meter, at the two different collecting stations.
Number of organisms per square meter
Station 1
Station 2
5030
2800
13700
4670
10730
6890
11400
7720
860
7030
2200
7330
4250
2810
15040
1330
4980
3320
11910
1230
8130
2130
26850
2190
17660
22800
1130
1690
With a significance level of 0.05, can we conclude that the densities are the same in the two…
The article "Effect of Microstructure and Weathering on the Strength Anisotropy of Porous
Rhyolite" (Y. Matsukura, K. Hashizume, and C. Oguchi, Engineering Geology, 2002:39-
17) investigates the relationship between the angle betwween cleavage and flow structure and
the strength of porous rhyolite. Strengths (in MPa) were measured for a mumber of
specimens cut at various angles. The mean and standard deviation of the strengths for each
angle are presented in the following table.
Angle Mean
0°
22.9
Sample Size
Standard Deviation
2.98
12
15°
22.9
1.16
30°
19.7
3.00
45°
14.9
2.99
60°
13.5
2.33
75°
11.9
2.10
90
14.3
3.95
6.
Can you conclude that strength varies with the angle?
Chapter 5 Solutions
Statistics for Engineers and Scientists
Ch. 5.1 - Find the value of Z/2 to use in expression (5.1)...Ch. 5.1 - Find the levels of the confidence intervals that...Ch. 5.1 - As the confidence level goes up, the reliability...Ch. 5.1 - The article Modeling Arterial Signal Optimization...Ch. 5.1 - In a sample of 100 steel wires the average...Ch. 5.1 - The article Application of Surgical Navigation to...Ch. 5.1 - The capacities (in ampere-hours) were measured for...Ch. 5.1 - Oven thermostats were tested by setting them to...Ch. 5.1 - In a sample of 80 ten-penny nails, the average...Ch. 5.1 - In a sample of 60 electric motors, the average...
Ch. 5.1 - The sugar content in a one-cup serving of a...Ch. 5.1 - Refer to Exercise 5. a. Find a 95% lower...Ch. 5.1 - Prob. 13ECh. 5.1 - Prob. 14ECh. 5.1 - Prob. 15ECh. 5.1 - Refer to Exercise 9. a. Find a 90% upper...Ch. 5.1 - Refer to Exercise 10. a. Find a 98% lower...Ch. 5.1 - Refer to Exercise 11. a. Find a 95% upper...Ch. 5.1 - Prob. 19ECh. 5.1 - A 95% confidence interval for a population mean is...Ch. 5.1 - Based on a large sample of capacitors of a certain...Ch. 5.1 - Sixty-four independent measurements were made of...Ch. 5.1 - A large box contains 10,000 ball bearings. A...Ch. 5.1 - Prob. 24ECh. 5.1 - Prob. 25ECh. 5.1 - Prob. 26ECh. 5.2 - In a simple random sample of 70 automobiles...Ch. 5.2 - During a recent drought, a water utility in a...Ch. 5.2 - A soft-drink manufacturer purchases aluminum cans...Ch. 5.2 - The article HIV-positive Smokers Considering...Ch. 5.2 - The article The Functional Outcomes of Total Knee...Ch. 5.2 - Refer to Exercise 1. Find a 95% lower confidence...Ch. 5.2 - Refer to Exercise 2. Find a 98% upper confidence...Ch. 5.2 - Refer to Exercise 4. Find a 99% lower confidence...Ch. 5.2 - A random sample of 400 electronic components...Ch. 5.2 - Refer to Exercise 9. A device will be manufactured...Ch. 5.2 - When the light turns yellow, should you stop or go...Ch. 5.2 - In a random sample of 150 customers of a...Ch. 5.2 - A sociologist is interested in surveying workers...Ch. 5.2 - Stainless steels can be susceptible to stress...Ch. 5.2 - The article A Music Key Detection Method Based on...Ch. 5.2 - A stock market analyst notices that in a certain...Ch. 5.3 - Find the value of tn1,/2 needed to construct a...Ch. 5.3 - Find the value of tn1, needed to construct an...Ch. 5.3 - Find the level of a two-sided confidence interval...Ch. 5.3 - True or false: The Students t distribution may be...Ch. 5.3 - The article Wind-Uplift Capacity of Residential...Ch. 5.3 - Prob. 6ECh. 5.3 - The article An Automatic Visual System for Marble...Ch. 5.3 - A chemist made eight independent measurements of...Ch. 5.3 - Six measurements are taken of the thickness of a...Ch. 5.3 - Fission tracks are trails found in uranium-bearing...Ch. 5.3 - The article Effect of Granular Subbase Thickness...Ch. 5.3 - The article Influence of Penetration Rate on...Ch. 5.3 - Prob. 13ECh. 5.3 - Prob. 14ECh. 5.3 - Prob. 15ECh. 5.3 - The concentration of carbon monoxide (CO) in a gas...Ch. 5.3 - The article Filtration Rates of the Zebra Mussel...Ch. 5.4 - To study the effect of curing temperature on shear...Ch. 5.4 - The article Some Parameters of the Population...Ch. 5.4 - The article Inconsistent Health Perceptions for US...Ch. 5.4 - The article Hatching Distribution of Eggs Varying...Ch. 5.4 - The article Automatic Filtering of Outliers in RR...Ch. 5.4 - A group of 78 people enrolled in a weight-loss...Ch. 5.4 - In experiments to determine the effectiveness of...Ch. 5.4 - A stress analysis was conducted on random samples...Ch. 5.4 - In a study to compare two different corrosion...Ch. 5.4 - An electrical engineer wishes to compare the mean...Ch. 5.4 - In a study of the effect of cooling rate on the...Ch. 5.4 - Refer to Exercise 11. Ten more welds will be made...Ch. 5.4 - The article The Prevalence of Daytime Napping and...Ch. 5.4 - The article Occurrence and Distribution of...Ch. 5.5 - In a test of the effect of dampness on electric...Ch. 5.5 - The specification for the pull strength of a wire...Ch. 5.5 - Angioplasty is a medical procedure in which an...Ch. 5.5 - Prob. 4ECh. 5.5 - Prob. 5ECh. 5.5 - Prob. 6ECh. 5.5 - In a study of contamination at landfills...Ch. 5.5 - Prob. 8ECh. 5.5 - A mobile computer network consists of a number of...Ch. 5.5 - The article Evaluation of Criteria for Setting...Ch. 5.5 - In a certain year, there were 80 days with...Ch. 5.6 - In a study comparing various methods of gold...Ch. 5.6 - Prob. 2ECh. 5.6 - In an experiment involving the breaking strength...Ch. 5.6 - A new post-surgical treatment is being compared...Ch. 5.6 - The article Differences in Susceptibilities of...Ch. 5.6 - The article Tibiofemoral Cartilage Thickness...Ch. 5.6 - During the spring of 1999, many fuel storage...Ch. 5.6 - Prob. 8ECh. 5.6 - The article Toward a Lifespan Metric of Reading...Ch. 5.6 - Prob. 10ECh. 5.6 - Measurements of the sodium content in samples of...Ch. 5.6 - Prob. 12ECh. 5.6 - Prob. 13ECh. 5.6 - In the article Bactericidal Properties of Flat...Ch. 5.6 - Prob. 15ECh. 5.7 - The article Simulation of the Hot Carbonate...Ch. 5.7 - The article Effect of Refrigeration on the...Ch. 5.7 - Transepidermal water loss (TEWL) is a measure of...Ch. 5.7 - Breathing rates, in breaths per minute, were...Ch. 5.7 - A group of five individuals with high blood...Ch. 5.7 - A sample of 10 diesel trucks were run both hot and...Ch. 5.7 - For a sample of nine automobiles, the mileage (in...Ch. 5.7 - Prob. 8ECh. 5.7 - Prob. 9ECh. 5.7 - Prob. 10ECh. 5.8 - Find the following values. a. 12,.0252 b. 12,.9752...Ch. 5.8 - Prob. 2ECh. 5.8 - Construct a 99% confidence interval for the...Ch. 5.8 - Prob. 4ECh. 5.8 - Scores on an IQ test are normally distributed. A...Ch. 5.8 - Prob. 6ECh. 5.8 - Boxes of cereal are labeled as containing 14...Ch. 5.8 - Prob. 8ECh. 5.8 - Following are interest rates (annual percentage...Ch. 5.8 - Prob. 10ECh. 5.8 - Prob. 11ECh. 5.8 - Prob. 12ECh. 5.9 - A sample of 25 resistors, each labeled 100, had an...Ch. 5.9 - Prob. 2ECh. 5.9 - The article Ozone for Removal of Acute Toxicity...Ch. 5.9 - Six measurements were made of the concentration...Ch. 5.9 - Five measurements are taken of the octane rating...Ch. 5 - A molecular biologist is studying the...Ch. 5 - Prob. 2SECh. 5 - The article Genetically Based Tolerance to...Ch. 5 - A sample of 87 glass sheets has a mean thickness...Ch. 5 - Prob. 5SECh. 5 - Prob. 6SECh. 5 - Leakage from underground fuel tanks has been a...Ch. 5 - Prob. 8SECh. 5 - Prob. 9SECh. 5 - Prob. 10SECh. 5 - In the article Groundwater Electromagnetic Imaging...Ch. 5 - Prob. 12SECh. 5 - Prob. 13SECh. 5 - Prob. 14SECh. 5 - A metallurgist makes several measurements of the...Ch. 5 - In a study of the lifetimes of electronic...Ch. 5 - The temperature of a certain solution is estimated...Ch. 5 - Prob. 18SECh. 5 - Prob. 19SECh. 5 - The answer to Exercise 19 part (d) is needed for...Ch. 5 - The carbon content (in ppm) was measured for each...Ch. 5 - Diameters, in mm, were measured for eight...Ch. 5 - A sample of eight repair records for a certain...Ch. 5 - Prob. 25SE
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, statistics and related others by exploring similar questions and additional content below.Similar questions
- An experiment was conducted to study the extrusion process of biodegradable packaging foam. Two of the factors considered for their effect on the unit density (mg/ml) were the die temperature (145 °C vs. 155 °C) and the die diameter (3 mm vs. 4 mm). The results are stored in [Packaging Foam 1]. Source: Data extracted from W. Y. Koh, K. M. Eskridge, and M. A. Hanna, "Supersaturated Split-Plot Designs," Journal of Quality Technology, 45, January 2013, pp. 61-72.At the 0.05 level of significance, 3mm 4mm 57.22 145 72.54 145 53.60 66.70 145 48.13 49.28 145 69.89 44.14 145 62.78 58.37 145 55.18 53.98 155 57.50 63.03 155 54.17 46.73 155 73.86 60.17 155 90.28 46.78 155 88.19 43.27 155 82.61 56.93 Die Temperature a. is there an interaction between die temperature and die diameter? b. is there an effect due to die temperature? c. is there an effect due to die diameter? d. Plot the mean unit density for each die temperature for each die diameter. e. What can you conclude about the effect of die…arrow_forwardThe article "Effect of Granular Subbase Thickness on Airfield Pavement Structural Response" (K. Gopalakrishnan and M. Thompson, Journal of Materials in Civil Engineering, 2008:331-342) presents a study of the amount of surface deflection caused by aircraft landing on an airport runway. A load of 160 kN was applied to a runway surface, and the amount of deflection in mm (y) was measured at various distances in m (x) from the point of application. The results are presented in the following table. y 0.000 3.24 0.305 2.36 0.610 1.42 0.914 0.87 1.219 0.54 1.524 0.34 1.830 0.24 a. Fit the linear model y = Bo + B1x + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. b. Fit the quadratic model y = Bo + Bịx + B2x² + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. %3D Fit the cubic model y = Bo + B1x + B2x? + B3x + E. For each coefficient, test the C. hypothesis that the coefficient is equal to 0. d. Which of the models in parts (a)…arrow_forwardAn article in the ASCE Journal of Energy Engineering [“Overview of Reservoir Release Improvements at 20 TVA Dams” (Vol. 125, April 1999, pp. 1–17)] presents data on dissolved oxygen concentrations in streams below 20 dams in the Tennessee Valley Authority system. The observations are (in milligrams per liter):arrow_forward
- 2. A city's transportation committee has conducted research on traffic and car accidents for downtown streets. There is a 9% chance of being involved in a car accident when 15 or more cars are driving on Johnson Street and a 7.5% chance when 20 or more cars are driving on Dublin Street. The two streets intersect to form a risk area with a radius of 0.1 mi. Approximate the density of cars per square mile in the risk area when 17 cars are on Johnson Street and 21 cars are on Dublin Street. Use 3.14 for TT. There are approximately 1,082 cars per square mile in the risk area. There are approximately 2,674 cars per square mile in the risk area. There are approximately 2,165 cars per square mile in the risk area. There are approximately 1,210 cars per square mile in the risk area.arrow_forwardWild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.5 5.2 6.8 4.6 6.5 5.3 5.1 6.1 4.4 5.5 4.1 7.9 4.1 5.1 5.9 5.4 6.1 6.9 5.4 5.1 6.6 Shall we reject or not reject the claim that there are no differences among the population means of sepal length for the different species of iris? Use a 5% level of significance. (a) What is the level of significance?State the null and alternate hypotheses. Ho: ?1 = ?2 = ?3; H1: Exactly two means are equal.Ho: ?1 = ?2 = ?3; H1: Not all the means are equal. Ho: ?1 = ?2 = ?3; H1:…arrow_forwardWild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.7 5.1 6.5 4.7 6.2 5.1 4.7 6.6 4.7 5.8 4.9 7.5 4.6 5.2 5.3 5.3 6.2 6.2 5.4 5.8 6.4 (b) Find SSTOT, SSBET, and SSW and check that SSTOT = SSBET + SSW. (Use 3 decimal places.) SSTOT = SSBET = SSW = Find d.f.BET, d.f.W, MSBET, and MSW. (Use 4 decimal places for MSBET, and MSW.) dfBET = dfW = MSBET = MSW = Find the value of the sample F statistic. (Use 2 decimal places.)What are the degrees of freedom? (numerator) (denominator)arrow_forward
- Wild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.9 5.8 6.9 4.8 6.5 5.6 4.6 6.4 4.9 5.7 4.3 7.7 4.8 5.8 5.6 5.4 6.3 6.3 5.8 5.5 6.6 Shall we reject or not reject the claim that there are no differences among the population means of sepal length for the different species of iris? Use a 5% level of significance. (b) Find SSTOT, SSBET, and SSW and check that SSTOT = SSBET + SSW. (Use 3 decimal places.) SSTOT = SSBET = SSW = Find d.f.BET, d.f.W, MSBET, and MSW. (Use 4 decimal places for MSBET, and…arrow_forwardWild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.7 5.4 6.8 4.1 6.3 5.4 5.0 6.7 4.4 5.4 4.3 7.3 4.6 5.5 5.3 5.7 6.5 6.7 5.2 5.3 6.8 Shall we reject or not reject the claim that there are no differences among the population means of sepal length for the different species of iris? Use a 5% level of significance. (a) What is the level of significance?State the null and alternate hypotheses. Ho: ?1 = ?2 = ?3; H1: All three means are different.Ho: ?1 = ?2 = ?3; H1: Not all the means are equal. Ho: ?1 = ?2 = ?3;…arrow_forwardWild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.9 5.5 6.7 4.1 6.8 5.8 5.2 6.5 4.5 5.4 4.5 7.2 4.1 5.4 5.2 5.2 6.2 6.9 5.6 5.2 6.7 Shall we reject or not reject the claim that there are no differences among the population means of sepal length for the different species of iris? Use a 10% level of significance. (a) What is the level of significance? 0.01 State the null and alternate hypotheses. O H,: H1 = H, = Hzi H;: All three means are different. O H,: H1 = H2 = Hzi H;: Exactly two means are equal. O H,: H, = H2 = Hai H,: At least two…arrow_forward
- The article "Two Different Approaches for RDC Modelling When Simulating a Solvent Deasphalting Plant" (J. Aparicio, M. Heronimo, et al., Computers and Chemical Engineering, 2002:1369–1377) reports flow rate (in dmh) and specific gravity measurements for a sample of paraffinic hydrocarbons. The natural logs of the flow rates (y) and the specific gravity measurements (x) are presented in the following table. х -1.204 0.8139 -0.580 0.8171 0.049 0.8202 0 673 0.8233 1.311 0.8264 1.959 0.8294 2.614 0.8323 3.270 0.8352 Fit the linear model y = Bo + B,x + ɛ. For each coefficient, test the hypothesis that the coefficient is equal to 0. Fit the quadratic model y = Bo + B,x + B2x? + E. For each coefficient, test the a. b. hypothesis that the coefficient is equal to 0. Fit the cubic model y = Bo + Bix + B2x² + Bax + E. For each coefficient, test the C. hypothesis that the coefficient is equal to 0. Which of the models in parts (a) through (c) is the most appropriate? Explain. Using the most…arrow_forwardFollowing are measurements of soil concentrations (in mg /kg) of chromium (Cr) and nickel (Ni) at20 sites in the area of Cleveland, Ohio. These data are taken from the article "Variation in NorthAmerican Regulatory Guidance for Heavy Metal Surface Soil Contamination at Commercial andIndustrial Sites" (A. Jennings and J. Ma, J. Environment Eng, 2007:587-609). Cr: 260 19 36 247 263 319 317 277 319 264 23 29 61 119 33 281 21 35 64 30Ni: 435 377 359 53 38 38 54 188 397 33 92 490 28 35 799 347 321 32 74 508 (a) Construct a histogram for each set of concentrations. (b) Find the 1st, 2nd and 3rd quartiles for the Cr concentrations (c) Find the 1st, 2nd and 3rd quartiles for the Ni concentrations.arrow_forwardWild irises are beautiful flowers found throughout the United States, Canada, and northern Europe. This problem concerns the length of the sepal (leaf-like part covering the flower) of different species of wild iris. Data are based on information taken from an article by R. A. Fisher in Annals of Eugenics (Vol. 7, part 2, pp. 179 -188). Measurements of sepal length in centimeters from random samples of Iris setosa (I), Iris versicolor (II), and Iris virginica (III) are as follows below. I II III 5.6 5.5 6.9 4.5 6.6 5.5 5.4 6.5 4.3 5.4 4.6 7.9 4.7 5.6 5.8 5.9 6.6 6.3 5.6 5.6 6.9 Shall we reject or not reject the claim that there are no differences among the population means of sepal length for the different species of iris? (b) Find SSTOT, SSBET, and SSW and check that SSTOT = SSBET + SSW. (Use 3 decimal places.) SSTOT = SSBET = SSW = Find d.f.BET, d.f.W, MSBET, and MSW. (Use 4 decimal places for MSBET, and MSW.) dfBET = dfW =…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
MATLAB: An Introduction with ApplicationsStatisticsISBN:9781119256830Author:Amos GilatPublisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...StatisticsISBN:9781305251809Author:Jay L. DevorePublisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...StatisticsISBN:9781305504912Author:Frederick J Gravetter, Larry B. WallnauPublisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...StatisticsISBN:9780134683416Author:Ron Larson, Betsy FarberPublisher:PEARSON
The Basic Practice of StatisticsStatisticsISBN:9781319042578Author:David S. Moore, William I. Notz, Michael A. FlignerPublisher:W. H. Freeman
Introduction to the Practice of StatisticsStatisticsISBN:9781319013387Author:David S. Moore, George P. McCabe, Bruce A. CraigPublisher:W. H. Freeman
MATLAB: An Introduction with Applications
Statistics
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Probability and Statistics for Engineering and th...
Statistics
ISBN:9781305251809
Author:Jay L. Devore
Publisher:Cengage Learning
Statistics for The Behavioral Sciences (MindTap C...
Statistics
ISBN:9781305504912
Author:Frederick J Gravetter, Larry B. Wallnau
Publisher:Cengage Learning
Elementary Statistics: Picturing the World (7th E...
Statistics
ISBN:9780134683416
Author:Ron Larson, Betsy Farber
Publisher:PEARSON
The Basic Practice of Statistics
Statistics
ISBN:9781319042578
Author:David S. Moore, William I. Notz, Michael A. Fligner
Publisher:W. H. Freeman
Introduction to the Practice of Statistics
Statistics
ISBN:9781319013387
Author:David S. Moore, George P. McCabe, Bruce A. Craig
Publisher:W. H. Freeman
Hypothesis Testing using Confidence Interval Approach; Author: BUM2413 Applied Statistics UMP;https://www.youtube.com/watch?v=Hq1l3e9pLyY;License: Standard YouTube License, CC-BY
Hypothesis Testing - Difference of Two Means - Student's -Distribution & Normal Distribution; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=UcZwyzwWU7o;License: Standard Youtube License