EBK MANUFACTURING PROCESSES FOR ENGINEE
6th Edition
ISBN: 9780134425115
Author: Schmid
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 5, Problem 5.97D
(a)
To determine
The riser placement.
(b)
To determine
The core placement.
(c)
To determine
The padding.
(d)
To determine
The chills.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
pouring basin in a sand casting?
3. Explain why a sprue should be tapered?
4. What are the disadvantages of die casting?
5. Explain the various kinds of patterns in use. What are the allowances provided, when making a pattern?
How do the patterns differ from the casting required?
Example#2
A cylindrical riser with diameter-to-length ratio = 1.0 is
to be designed for a sand casting mold. The casting
geometry is illustrated in Figure. If the mold constant =
19.5 min/in? in Chvorinov's Rule, determine the
dimensions of the riser so that the riser will take 0.5
minute longer to freeze than the casting itself.
-2.5-
-6.0-
-1.5
3.0
2.5 radius -
3.0
5.0
15.0
3. (Slow or Fast, which one? – Circle one) cooling rates results in coarse dendritic structures.
4. The higher the viscosity of the melt, the .
its fluidity?
5. Name 3 defects in casting:
6. Internal or external
are an effective means of reducing shrinkage porosity during solidification.
7. Is green-sand molding expensive?
8.
.... are inserts placed in the molds to form the hollow regions in casting.
9. The method of casting turbine blades:
Sample A
10. Which one has higher stiffness? Sample A or Sample B
Sample B
11. Which one has higher toughness? Sample A or Sample B
12. Which one has higher strength? Sample A or Sample B
13. Which one has higher ductility? Sample A or Sample
14. Higher
......... means more rigidity.
Strain
15. Before the no-slip point, the velocity is (higher or lower, which one? - Circle one)
16. In flat-rolling process, using smaller diameter rolls (increases or decreases, which one? - Circle one) the roll
force.
17. Balls for ball bearings can be made by
rolling…
Chapter 5 Solutions
EBK MANUFACTURING PROCESSES FOR ENGINEE
Ch. 5 - Prob. 5.1QCh. 5 - Prob. 5.2QCh. 5 - Prob. 5.3QCh. 5 - Prob. 5.4QCh. 5 - Prob. 5.5QCh. 5 - Prob. 5.6QCh. 5 - Prob. 5.7QCh. 5 - Prob. 5.8QCh. 5 - Prob. 5.9QCh. 5 - Prob. 5.10Q
Ch. 5 - Prob. 5.11QCh. 5 - Prob. 5.12QCh. 5 - Prob. 5.13QCh. 5 - Prob. 5.14QCh. 5 - Prob. 5.15QCh. 5 - Prob. 5.16QCh. 5 - Prob. 5.17QCh. 5 - Prob. 5.18QCh. 5 - Prob. 5.19QCh. 5 - Prob. 5.20QCh. 5 - Prob. 5.21QCh. 5 - Prob. 5.22QCh. 5 - Prob. 5.23QCh. 5 - Prob. 5.24QCh. 5 - Prob. 5.25QCh. 5 - Prob. 5.26QCh. 5 - Prob. 5.27QCh. 5 - Prob. 5.28QCh. 5 - Prob. 5.29QCh. 5 - Prob. 5.30QCh. 5 - Prob. 5.31QCh. 5 - Prob. 5.32QCh. 5 - Prob. 5.33QCh. 5 - Prob. 5.34QCh. 5 - Prob. 5.35QCh. 5 - Prob. 5.36QCh. 5 - Prob. 5.37QCh. 5 - Prob. 5.38QCh. 5 - Prob. 5.39QCh. 5 - Prob. 5.40QCh. 5 - Prob. 5.41QCh. 5 - Prob. 5.42QCh. 5 - Prob. 5.43QCh. 5 - Prob. 5.44QCh. 5 - Prob. 5.45QCh. 5 - Prob. 5.46QCh. 5 - Prob. 5.47QCh. 5 - Prob. 5.48QCh. 5 - Prob. 5.49QCh. 5 - Prob. 5.50QCh. 5 - Prob. 5.51QCh. 5 - Prob. 5.52QCh. 5 - Prob. 5.53QCh. 5 - Prob. 5.54QCh. 5 - Prob. 5.55QCh. 5 - Prob. 5.56QCh. 5 - Prob. 5.57QCh. 5 - Prob. 5.58QCh. 5 - Prob. 5.59QCh. 5 - Prob. 5.60QCh. 5 - Prob. 5.61PCh. 5 - Prob. 5.62PCh. 5 - Prob. 5.63PCh. 5 - Prob. 5.64PCh. 5 - Prob. 5.65PCh. 5 - Prob. 5.66PCh. 5 - Prob. 5.67PCh. 5 - Prob. 5.68PCh. 5 - Prob. 5.69PCh. 5 - Prob. 5.70PCh. 5 - Prob. 5.71PCh. 5 - Prob. 5.72PCh. 5 - Prob. 5.73PCh. 5 - Prob. 5.74PCh. 5 - Prob. 5.75PCh. 5 - Prob. 5.76PCh. 5 - Prob. 5.77PCh. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - Prob. 5.82PCh. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - Prob. 5.85PCh. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - Prob. 5.89PCh. 5 - Prob. 5.90PCh. 5 - Prob. 5.91PCh. 5 - Prob. 5.92PCh. 5 - Prob. 5.93DCh. 5 - Prob. 5.94DCh. 5 - Prob. 5.95DCh. 5 - Prob. 5.96DCh. 5 - Prob. 5.97DCh. 5 - Prob. 5.98DCh. 5 - Prob. 5.99DCh. 5 - Prob. 5.100DCh. 5 - Prob. 5.101DCh. 5 - Prob. 5.102DCh. 5 - Prob. 5.103DCh. 5 - Prob. 5.104DCh. 5 - Prob. 5.105DCh. 5 - Prob. 5.106DCh. 5 - Prob. 5.107DCh. 5 - Prob. 5.108DCh. 5 - Prob. 5.109DCh. 5 - Prob. 5.110DCh. 5 - Prob. 5.111DCh. 5 - Prob. 5.112DCh. 5 - Prob. 5.113DCh. 5 - Prob. 5.114DCh. 5 - Prob. 5.115D
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3) What are the means of elastic and plastic deformations? List the passageway (gating system) elements in sand casting moulds and show them with drawing?arrow_forwardCalculate the size of a cylindrical riser (Height and diameter equal ) necessary to feed slab casting 45 * 45 * 25 cm with a side riser , casting poured horizontally in to the mould.Use caine's equation and take constants in caine equation as a= 0.18; b = 0.05 and c= 1.0.arrow_forwardConverging passage is used for feeding the liquid molten metal into the mould to (a) increase the rate of feeding (b) quickly break off the protruding portion of the casting (c) decrease wastage of cast metal (d) avoid aspiration of airarrow_forward
- (1) In sand casting, the volumetric size of the pattern is: (a) bigger than, (b) the same as, or (c) smaller than the cast part (2) Machining processes include which of the following (two correct answers): (a) casting, (b) drilling, (c) extrusion, (d) forging, (e) shaping, (f), and painting? (3) Aluminum sections used for making metal doors and windows are made by which process: (a) Rolling, (b) welding, (c) extrusion, (d) turning. (4) The average flow stress is the flow stress multiplied by which of the following factors: (a) n, (b) (1-n), (c) 1/n, or (d) 1/(1+n), where n is the strain hardening exponent? (5) The strength of a brazed joint is typically (a) equal to, (b) stronger than, or (c) weaker than soldered joint? (6) Thread cutting operation is normally performed on which one of the following machine tools: (a) drill press, (b) lathe, (c) milling machine, (d) planer, or (e shaper?arrow_forwardIs my solution correct??arrow_forwardFor the casting of the part, whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally the mold in the most suitable form for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)arrow_forward
- 6- A pure copper is to be heated for casting a large plate in an open mold. The plate has dimensions: length = 50cm, width = 25cm, and thickness = 7cm. Compute the amount of heat that must be added to the metal to heat it to a temperature of 1176°C for pouring. Assume that the amount of metal heated will be 10% more than what is needed to fill the mold cavity. Properties of the metal are: density = 8.94 g/cm3, melting point = 1082°C, specific heat of the metal = 410 J /kg C° in the solid state and 376 J/Kg C° in the liquid state, and heat of fusion = 186 J/g.arrow_forwardh, is placed on the top of the mold cavity of a closed type sand mould as shown in the figure. If the riser is of constant volume, then the rate of solidification in the riser is the least when the lindrical blind riser with diameter dand height is ratio h: d is Sprue basin Riser Mould cavityarrow_forwardWhich of these factors causes more porosity to form toward the interior of a casting rather than toward the outside? (a) Gasses are less soluble in the solid metal than the liquid, so solidified areas push dissolved gasses toward the interior. (b) Casting under a vacuum causes gasses near the liquid metal surface to be drawn out of the liquid during solidification. (c) The feeding structures of the mold are designed to force entrapped air into the center of the casting. (d) Draft on the mold wall forces air bubbles toward the interior of the solidifying metal. (e) None of the above Non-eutectic alloys (most commercial alloys) solidify over a temperature range. Which of the following statements explains how this affects the casting process. (a) Solidified non-eutectic alloys are especially difficult to remove from metal dies (b) Non-eutectic alloys have significantly less fluidity than pure metals or eutectic alloys. (c) Non-eutectic alloys solidify starting from the outside of the…arrow_forward
- a riser in the shape of a sphere is to be designed for a sand casting mold. the casting is a rectangular plate, with length 200mm, width 100mm, and thickness 18mm. if the total solidification time of the casting itself is known to be 3.5 mm, determine the diameter of the riser so that it will take 25% longer for the riser to solidify. assume a value of 2 for ‘n’ m( the exponent in chvorinov’s rule). know the volume and surface area of a sphere.arrow_forwardEX.3//A cylindrical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 7.5 cm x 12.5 cm x 2.0 cm. Previous observations have indicated that the total solidification time (TTs) for this casting =1.6 min. The cylinder for the riser will have a diameter-to-height ratio=1.0. Determine the dimensions of the riser so that its TTS = 2.0 min.arrow_forward(3):-The suitable type of casting to making tubs and cylinders is by a --- a- Lost wax casting b- Centrifugal casting c- Sand casting d- Continuous casting (4):- The surface of product Extruded by ----- Extrusion process has high smooth a- Hot b- Cold e- Warm (5):- High temperature leads to ----- he metal's ability to form a- Decreases b- Increases c- Non affected onarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Casting Metal: the Basics; Author: Casting the Future;https://www.youtube.com/watch?v=2CIcvB72dmk;License: Standard youtube license