Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 5.40P
Consider the knee space shown in Fig. 5-11. The vertical dimension is 8 ft, the horizontal dimension is 3 ft, and the space is 20 ft long. The walls and roof surrounding the space all have an overall heat-transfer coefficient of about
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Can someone please help me with creating an excel spreadsheet to calculate heat transfer phenomenon from a cylindrical fuel rod to the coolant?
The excel sheet needs to be able to calculate these 3 things: Heat generated in a fuel rod at a distance ‘r’ from the center; Total Heat generated in the Reactor; the maximum temperature in the fuel and the cladding surface temperature, for a fuel rod at a distance ‘r’ from the center. The fuel used in this will be UO2 and there is a thin layer of helium that will separate the fuel from the cladding material.
The user input parameters will be: the thermal neutron flux at the core, thermal conductivity of fuel, thermal conductivity of helium, thermal conductivity of the cladding, thickness of the helium layer, thickness of the cladding, diameter of the fuel pellet, fuel rod location (r), Cylindrical Reactor Size, and the fuel enrichment. For the fluid the user input will be coolant temperature and the heat transfer coefficient.
Q1) A polished metal pipe (8 cm) owtside diameter and 350 K temperature at the outer surface is exposed to ambient conditions at 285 K temperature. The emissivity of the surface is 0.3 and the convection coefficient of heat transfer is 13.5 Wim2-deg. What would be the overall coefficient of heat transfer by the combined mode of convection and radiation” Q2 find the pressure point (1) if the amospheric pressure is(70kpajihl =0 2,h2=0.4,h3=0. ‘)(p. =13600kg/m3. poil=850kg/m3)
Q2: A: The exterior wall of a single-story office building near Chicago is 3 m high and 15 m long. The wall consists of 100-mm face brick, 40-mm polystyrene insulating board. 150-mm lightweight concrete block, and an interior 16-mm gypsum. The wall contains three single-glass of 3 mm thickness windows 1.5 m high by 2 m long. Calculate the heat loss through the wall at design conditions if the inside temperature is (20 °C). The outside temperature is (-18 "C).
Chapter 5 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 5 - Determine the thermal conductivity of 4 in. (100...Ch. 5 - Compute the unit conductance C for 512 in. (140...Ch. 5 - Compute the unit thermal resistance and the...Ch. 5 - What is the unit thermal resistance for an inside...Ch. 5 - Compute the thermal resistance per unit length for...Ch. 5 - Assuming that the blocks are not filled, compute...Ch. 5 - The partition of Problem 5-4 has still air on one...Ch. 5 - The pipe of Problem has water flowing inside with...Ch. 5 - Compute the overall thermal resistance of a wall...Ch. 5 - Compute the overall heat-transfer coefficient for...
Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
What is the weight in newtons of an object that has a mass of (a) 8 kg, (b) 0.04 kg, (c) 760 Mg?
Statics and Mechanics of Materials (5th Edition)
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...
Thermodynamics: An Engineering Approach
23.23 A highly oxidized and uneven round bar is being turned on a lathe. Would you recommend a small or a large...
Manufacturing Engineering & Technology
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
HEAT+MASS TRANSFER:FUND.+APPL.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 2.5-m-tall steel cylinder has a cross-sectional area of 1.5 m2. At the bottom, with a height of 0.5 m, is liquid water, on top of which is a 1-m high layer of gasoline, relative density of 0.8. The gasoline surface is exposed to atmospheric air at 101 kPa. What is the gage pressure at the liquid interface? what is the answer? a.0.077 atm b.15.839 psi c. 1.139 mmHg d.108.848 kPaarrow_forwardYou are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…arrow_forwardSipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.arrow_forward
- (a) The temperature at the surface of the heating rod, T1. (b) If the salt solution temperature is 300 degree Celcius, what is the value of convection heat transfer coefficient, h of the salt solution ? (c) If the heating rod is not covered by metallic cylinder and corresponds to the result of part (a) and (b), how much the rate of energy transfer to the salt solution ? (d) Compare and discuss the difference of heat transfer with and without the matallic cylinder.arrow_forwardHi, can you help me with the following problem? A thermally insulated tank of water 2 m x 2 m, depth 1 m is stirred with a paddle for threehours. If the paddle is driven by a motor whose shaft power is 8 kW determine the rate ofchange of temperature in degrees C per hr and the increase in temperature of the water.The specific heat of water is 4200 J/kgC. Identify a system and start your analysis from anappropriate form of the Fist Law of Thermodynamicsarrow_forwardWhat is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.arrow_forward
- H.W: 10-02-2021: The exterior wall of a building consists of 100 mm thick face brick (k = 0.9 Wm¯'K'), 40 mm thick polystyrene insulating board (k 0.036 Wm'K¯), 125 mm thick concrete block (k = 1.8 Wm¯'K') and 15 mm thick interior gypsum board (k = 0.18 Wm K). The inside and outside convective heat transfer coefficients are 6.5 Wm K and 22.5 Wm K respectively. The outside air temperature is -5°C and the inside air temperature is 20°C. The wall is 3 m high and 15 m long. Calculate (i) the rate of heat loss through the wall,arrow_forwardA cylindrical storage tank with diameter of 4m and a length of 10 m will hold a fluid whose temperature must be maintained at 347k. in order to size the heater required for the tank the following worst-case scenario is considered: Ambient temperature=-20 wind speed=20m/s tank wall temperature=347k what size (kW) heater will be needed?arrow_forwardAnswer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg. °C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1.Cmin 2.Maximum heat transfer rate 3.Heat transfer surface areaarrow_forward
- Q1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a fluid at 20 C. The convection heat- transfer coefficient is 15 W/m2 C. Determine the dimension of the block that it is just considered as lumped-capacity system. Calculate : (1) the time the center of the sphere reaches the half value of initial temperature and, (2) the heat loss from the block at that time.arrow_forwardHeat Transfer Problem 1arrow_forwardA camera used for monitoring marine life is placed in water where T.. -5°C and the convection heat transfer coefficient h=1420 W/m²K. The camera is operating, but its battery is experiencing thermal runaway, causing the camera to become very hot, and there is volumetric heat generation, qe inside it. There is no heat generation within the waterproof, protective enclosure surrounding it. 00:08 The camera is already compromised; however, its owner hopes to save the protective case. Each interface (between layers A and B and between layers B and C) must not exceed a temperature of 185°C, or these plastic, protective layers will begin to melt. Approximate the camera and its casing as a composite, rectangular object with flat surfaces. The device's total thickness, L=LA + 2LB +Lc, is much smaller than its area (into the page); therefore, 1-D conduction can be approximated through the layers. On the left surface of layer A, the temperature is measured to be T₁ = 8.0°C, and the temperature on…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license