Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.24P
Estimate the overall heat-transfer coefficient for a
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Calculate the heat loss through a 3-in. thick insulation board that has an area of 2-
ft² and a k-value of 0.25. Assume the average temperature difference across the
material is 70°F.
Q = 11.66-Btu/hr
Q = 10.99-Btu/hr
Q = 10.66-Btu/hr
Q = 11.99-Btu/hr
Hide hint for Question 1
Utilize the (Q = k*A*AT/thickness) equation.
Question 1.2:Consider heat loss through the two walls of a house on a winter night. The walls are identical, except that one of them has a tightly fit glass window. Through which wall will the house lose more heat? Explain.
Question 2.1: What advantage does the effectiveness-NTU method have over the LMTD method?
a pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos ( K= 0.396(btu-in)/(hr-ft-F) followed by a layer of cork 1.5 inches thick ( K= 0.30 (btu-in)/ft (hr-ft-F). if the temperature of the outer surface of the cork and pipe is 90 F and 290 F RESPECTIVELY, calculate the heat loss per 100 ft of insulated pipe in btu/hr
Chapter 5 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 5 - Determine the thermal conductivity of 4 in. (100...Ch. 5 - Compute the unit conductance C for 512 in. (140...Ch. 5 - Compute the unit thermal resistance and the...Ch. 5 - What is the unit thermal resistance for an inside...Ch. 5 - Compute the thermal resistance per unit length for...Ch. 5 - Assuming that the blocks are not filled, compute...Ch. 5 - The partition of Problem 5-4 has still air on one...Ch. 5 - The pipe of Problem has water flowing inside with...Ch. 5 - Compute the overall thermal resistance of a wall...Ch. 5 - Compute the overall heat-transfer coefficient for...
Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- On a multi-layered square wall, the thermal resistance of the first layer is 0.005 ° C / W, the resistance of the second layer is 0.2 ° C / W, and the third layer is 0.1 ° C / W. The overall temperature gradient in the wall is multilayered from one side. to the other side is 70 ° C. a. Determine the heat flux through the walls. = Answerwatts / m2. b. If the thermal resistance of the second layer is changed to 0.4 ° C / W, what is the effect in% on heat flux, assuming the temperature gradient remains the same? = AnswerAnswer%.arrow_forward1. A small metal building is to be constructed of corrugated steel sheet walls with a total wall surface area of about 300 m². The air conditioner consumes about 1 kW of electricity for every 4 kW of cooling supplied and two wall construction are to be compared on the basis of cooling costs. Assume that electricity costs S0.15/kWh. Determine the electrical energy savings per week of using 260 mm of fiberglass batt insulation to the steel sheet wall (U-0.17 W/m² "C) instead of 159 mm of fiberglass insulation (U-0.31 W/m² °C) assuming an overall temperature difference of 20 °C across the wall.arrow_forward2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)arrow_forward
- An experiment was conducted to determine surface convective heat transfer coefficient for peas being frozen in an air-blast freezer. For this purpose, a metal analog of peas was used. The analog was a solid copper ball with a diameter of 1 cm. A small hole was drilled to the center of the copper ball, and a thermocouple junction was located at the center using a high-conductivity epoxy. The density of copper is 8954 kg/m³, and its specific heat is 3830 J/(kg K). The copper ball (at a uniform initial temperature of 10 °C) was hung in the path of air flow (at -40 °C) and the center temperature indicated by the thermocouple was recorded. The following table lists the temperature at 1-min intervals for 14 min. Determine the surface heat transfer coefficient from these data. Time (s) 0 60 120 180 240 300 360 420 480 540 600 660 720 780 840 Temp (°C) 10 9 8 7 6 5 4 3,5 2,5 1 1 0 -2 -2 -3arrow_forwardOn a multi-layered rectangular wall, the thermal resistance of the first layer is 0.005 ° C / W, the resistance of the second layer is 0.2 ° C / W, and the third layer is 0.1 ° C / W.The overall temperature gradient in the wall is multilayered from one side. to the other side is 50 ° C. a. Determine the heat flux through the walls. = Answer watts / m2. b. If the thermal resistance of the second layer is changed to 0.3 ° C / W, what is the effect in% on heat flux, assuming the temperature gradient remains the same? = AnswerAnswer %.arrow_forwardOn a multi-layered square wall, the thermal resistance of the first layer is 0.005 ° C / W, the resistance of the second layer is 0.3 ° C / W, and the third layer is 0.1 ° C / W. The overall temperature gradient in the wall is multilayered from one side. to the other side is 50 ° C. a. Determine the heat flux through the walls. = Answer watts / m2. b. If the thermal resistance of the second layer is changed to 0.1 ° C / W, what is the effect in% on heat flux, assuming the temperature gradient remains the same? = AnswerAnswer %.arrow_forward
- Build a spreadsheet to do the step by step method for estimating the temperature of unprotected steel work exposed to the ASTM E119 Standard Fire. Assume a convective heat transfer coefficient of 25 W/m2K and an emissivity of 0.5. Assume the specific heat to remain constant at 600 J/kgK. Use a time step of 30 seconds and an ambient temperature of 20°C. Provide an Excel plot showing the curves of the fire and a steel member through a time of 60 minutes with F/V ratios of: a)25 m-1 b)100 m-1 c)200 m-1 d)300 m-1 Note your plot should contain 5 curves. One for the fire and one for each of the F/V values. Also on the spreadsheet, highlight in green, the cells identifying the temperature of the unprotected steel member with an F/V of 200m-1 at the following times: a)3 minutes b)10 minutes c)20 minutes d)50 minutesarrow_forwardDetermine the rate of heat transfer and the overall heat transfer coefficient for the composite wall shown below assuming the width is 1m. 10cm T1 = 100°C h=6W/m2.K 20cm Ka 1.9 W/m.K 10cm Kb=0.05 W/m.K Kc 0.1 W/m.K 10cm Kd=3 W/m.K 10cm T2 = 35°C h₂ = 10 W/m2.Karrow_forwardQ2/ An insulated steam pipe having an outside Steam pipe diameter of 30 mm is to be covered with two Better ination (4) Paer ination () layers of insulation, each haying thickness of 20 mm. The thermal conductivity of one material is 5 times that of the other. Sm L 1. Assuming that the inner and outer surface temperatures of composite insulation are fixed, how much will heat transfer be increased when better insulation material is next to the pipe than it is the outer layer?arrow_forward
- Еxample:- In a warm room, a naked resting person has a skin temperature of 33°C If the room temperature is 29°C and the body surface area is 1.5m2 .What is the rate of heat loss due to convection if Kc=7.1 watt/m2 .k?arrow_forwardA furnace wall is to be designed to transmit a maximum heat flux of 220 Btu/hr.ft of wall area. The inside and outside wall temperatures are to be 2200 • F and 320 ° F. Determine the most economical arrangement of bricks measuring (9 in x 4; in x 3 in). If they are made from materials one with ak of 0.44 Btu/hr. ft. ° F and maximum usable temperature of 1700 ° F and other with a k of 0.94 Btu/hr. ft. ° F and a maximum usable temperature of 2400 ° F. Bricks made of each material cost the same amount and may be laid in any manner (but bricks must remain intact, i.e., no partial bricks). After you answer the question, determine the percent increase in heat flux if there are two -in.-diameter steel bolts extending through the wall per square foot of wall are. (k of steel = 22 Btu/hr. ft. F)|arrow_forwardQuestion 5 Heat transfer A domestic refrigerator with inner dimensions of 0.7 m by 0.7 m at the base and height 1 m was designed to maintain a set temperature of 6 °C. The bodies consist of two 10- mm-thick layers of Aluminium (k = 225 W/mK) separated by a 30 mm polyurethane insulation (k=0.028 W/mK). If the average convection heat transfer coefficient at the inner and outer surfaces are 11.6 W/m2K and 14.5 W/m2K respectively, calculate: WAO Data: Hgt = L2 = ho3= W = k2 = hi = L1 = L3 3= T01= m, k;= k3 = To2 = %3D %3D %3D %3D %3D %3D %3D Area= 5.1 the individual resistance(R) for each thermal layer, as well as for the total of the refrigerator,arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license