Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 5.10P
Compute the overall heat-transfer coefficient for a frame construction wall made of brick veneer (120 lbm/ft3) with 3 in. insulation bats between the
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
Calculate the over-all coefficient of heat transfer U for a piece of glass1/8-in thick, exposed to still air at 70 °F on one side and 0 °F air moving at15 mph on the other side.
Chapter 5 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 5 - Determine the thermal conductivity of 4 in. (100...Ch. 5 - Compute the unit conductance C for 512 in. (140...Ch. 5 - Compute the unit thermal resistance and the...Ch. 5 - What is the unit thermal resistance for an inside...Ch. 5 - Compute the thermal resistance per unit length for...Ch. 5 - Assuming that the blocks are not filled, compute...Ch. 5 - The partition of Problem 5-4 has still air on one...Ch. 5 - The pipe of Problem has water flowing inside with...Ch. 5 - Compute the overall thermal resistance of a wall...Ch. 5 - Compute the overall heat-transfer coefficient for...
Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Compute the hydraulic radius for a circular drain pipe running half full if its inside diameter is 300 mm.
Applied Fluid Mechanics (7th Edition)
The spring of k and unstretched length 1.5R is attached to the disk at a radial distance of 0.75R from the cent...
Engineering Mechanics: Statics
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
Determine the velocity of block D if end A of the rope is pulled down with a speed of vA = 3 m/s.
Engineering Mechanics: Dynamics (14th Edition)
Three rigid bodies, 2,3, and 4, are connected by four springs as shown in the figure. A horizontal force of 1,0...
Introduction To Finite Element Analysis And Design
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Presents the diagram of the problem, necessary formulas, clearance and numerical solution: An iron plate 2 cm thick has a cross-sectional area of 5,000 cm2. One of the faces is at 150 ◦C and the other is at 140 ◦C. How much heat flows through the plate each second? For iron, kT = 80 W/m K.arrow_forward1. Calculate the overall heat-transfer coefficient (U=?) for a frame construction wall made of brick veneer (120-lbm/ft³) with 3-in. fiberglass insulation bats between the 2x4 wood studs (softwood) that are 16-in. on center. The wind velocity is 15-mph. Fill out the table below also utilizing materials data from the textbook. Also, calculate the total heat loss if the referenced wall was 9-ft tall and 35-ft in length set in Ohio, Clevland @ 99% winter OAT with an indoor setpoint of 75°F. Hint: 2x4 wood studs are 16-in. on center and 2-in. thick by 4-in. deep thus the empty space between each stud is 14-in. Remember use R = L/K & R = 1/C for materials. Between Frame (R-Value) At Framing (R-Value) Outside Surface 4-in. Face Brick (k=middle value) 1/2-in. Sheathing reg. density 3-in. Insulation Batt 2"x4" Wood Studs (k=middle value) 1/2-in. Gypsum Board Inside Surface Total (R-Value): ● U = ● Q= Btu/(hr-ft²-F) Btu/h Heat Lossarrow_forwardTask 02 Water flows through a cast steel pipe ( k = 50 W/m.K ) with an outer diameter of 104 mm and 2 mm wall thickness. (i). Calculate the heat loss by convection and conduction per metre length of un insulated pipe when the water temperature is 15 0C , the outside air temperature is -10 0C , the water side heat transfer coefficient is 30 kW/m2.K and the outside heat transfer coefficient is 20 W/m2.K . (ii). Calculate the corresponding heat loss when the pipe is lagged with insulation having an outer diameter of 365 mm, and thermal conductivity of k= 0.05 W/m.Karrow_forward
- 1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at To = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant T, h Chip = 200 W/m2 · K, what is the maximum allowable chip power? If the coolant is a If the coolant is air and the corresponding convection coefficient is h dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?arrow_forward1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant Chip If the coolant is air and the corresponding convection coefficient is h = 200 W/m² · K, what is the maximum allowable chip power? If the coolant is a dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?arrow_forwardQ7/ A hollow sphere is constructed of aluminum with an inner diameter of 4 cm and an outer diameter of (8cm). The inside temperature is (100-C) and the outer temperature is (50•C). Calculate the heat transfer.arrow_forward
- Presents the diagram of the problem, necessary formulas, clearance and numerical solution: A metal plate 4 mm thick has a temperature difference between its two faces of 32 ◦C. It transmits 200 kcal/h through an area of 5 cm2. Calculate the thermal conductivity of the metal in W/m K.arrow_forward11. A steam pipe, 3-cm ID, 5 mm thick and 10 meters long, permits a 100°C water flowing inside. If the outside temperature is at 30°C, what is the computed thermal resistance in °C/W? Use k = 0.015 W/m-C. 0.305 0.430 0.164 O 0.193arrow_forwardAn oil storage tank has 20mm steel walls covered with 50mm of fiber glass insulation. if the oil temperature is kept at 150 degree Celsius, what is the rate of heat loss when the outside temperature is 20 degree Celsius and external air coefficient is 20W/m². How much would the heat loss be reduced by doubling the thickness of the insulation?arrow_forward
- You are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…arrow_forwardAn insulated steam pipe is used to transport high-temperature steam from one building to another. The pipe has a diameter of 500 mm, a surface temperature of 164 °C and is exposed to ambient air at -10 °C. The pipe is subjected to an extermal forced convection as the air moves in a cross-flow over the pipe at a speed of 5 m/s (see figure below). a. What are the main assumptions? b. What is the heat loss per unit length of pipe without insulation? c. What is the heat loss per unit length of pipe if the insulation thickness is 10 mm? V = 5 m/s Too= -10 °C Air Tsi = 150 °C Insulation k, = 0.026 W/m-K D = 500 mm Ts.o Os8s 50 mm Steam Thermophysical Properties of Air at Atmospheric Pressure' k 10 4.107 (N-s/m) v• 10 (m/s) a 10 (m/s) T (K) (kg/m') (kJ/kg - K) (W/m K) Pr 100 3.5562 1.032 71.1 2.00 9.34 2.54 0.786 150 2.3364 1.012 103.4 4.426 13.8 5.84 0.758 200 1.7458 1.007 132.5 7.590 18.1 10.3 0.737 250 1.3947 1.006 159.6 11.44 22.3 15.9 0.720 300 1.1614 1.007 184.6 15.89 26.3 22.5 0.707…arrow_forwardA modern cabin has a concrete floor that is 4.50 inches thick. Aroaring fire keeps the interior of the cabin at 21.0 0C while the airtemperature below the cabin is a chilly 2.00 0C. How much heat(J) is lost through the concrete floor in 4 hrs if the cabin measures4.50 m by 6.50m to 3 sig fig?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license