Determine the force T required to hold the uniform bar of mass m and length L in an arbitrary angular position
Want to see the full answer?
Check out a sample textbook solutionChapter 3 Solutions
Engineering Mechanics: Statics
Additional Engineering Textbook Solutions
Manufacturing Engineering & Technology
Heating Ventilating and Air Conditioning: Analysis and Design
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
- The dimensions a = 2 m and b = 1 m. The couple M = 2400 N-m. The spring constant is k = 6000 N/m, and the spring would be unstretched if h = 0. The system is in equilibrium when h = 2 m and the beam is horizontal. Determine the force F and thereactions at A.arrow_forwardDetermine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 90 N and (a) 0 = 29°, 3= 25° and (b) = 14°, 3 = 37° Answers: (a) Fn = (b) Fn = i i B BI A N, Ft= N, Ft= i N Narrow_forwardThe homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.arrow_forward
- The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and luggage is 110 kg with mass center at G. Determine and plot the force in the hydruaulic cylinder BC (report your answer as a positive value) as a function of over the range 5° 0 ≤ 36°, then answer the questions. Assume DE = 2070 mm, CD = 1280 mm, c = 1680 mm, d = 1130 mm, e = 570 mm, f = 2380 mm. t Questions: E B i D If 0 = 11°, BC = If 0 = 21°, BC = i Over this range, the maximum value for BC = i N N N and occurs when 8 =arrow_forwardDetermine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 118 N and (a) e = 30°, B = 25° and (b) e = 21°, B = 29° Answers: (a) Fn= i N, F: = i N (b) Fn = i N. F:= Narrow_forwardThe jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?arrow_forward
- The cable AB prevents bar OA from rotating clockwise about the pivot O. If the cable tension is 820 N, determine the n- and t- components of this force acting on point A of the bar. 2.0 m B Answers: Tn= i Tt= i Attempts: 0 of 4 used Submit Answer -1.5 m Save for Later 63⁰ Z Z N Narrow_forwardThe jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.2 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 40° m 5 KN -2.9 m 1.2 m Questions: (a) If x = 0.8 m, R= (b) If x= 3.2 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN.arrow_forwardThe homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. A 33° = 0.40 B 2.0 darrow_forward
- The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 37° 6 KN 1.2 m 2.8 m Questions: (a) If x= 1.6 m, R= i (b) If x= 3.3 m, R= i (c) The minimum value for R = i (d) The pin should be designed to hold i kN kN kN at x = kN. i Earrow_forwardthe uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position through the tension P in the cable. for position theta=60° calculate the tension T in the horizontal anchor cable 6 m 6 m 8 2m T Barrow_forwardThe jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.0 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 34° x 1.3 m 6 kN -2.9 marrow_forward
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L