Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 2, Problem 2.51P
To determine
The condition of heat transfer as either steady state or transient, and the variation of heat flux with radius.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Find the steady-state temperature distribution in a (very long) solid cylinder if the boundary temperatures are T(s=0, θ, z)=0 and T(s, θ, z=0)=s*sinθ
The initial temperature of a 50 cm long silver wire is 50 °C. The circumference of the wire in question is completely insulated, but both ends are kept at a temperature of 0 °C (zero degrees Celsius). Obtain the heat conduction along the wire as a function of time and position and, taking a single term in the solution, determine how many degrees Celsius the temperature in the middle of the rod will be after 7 minutes. (For silver wire, α=1.70 cm2/s.)
In this question, we are concerned with the evolution of the temperature u(x, t) in a
homogeneous thin heat conducting rod of length L = 1. We can consider that the rod
is laterally insulated as to have a one-dimensional problem. The evolution of the temperature
is governed by the one-dimensional heat equation
ди
0 0
= K
Ət
Əx2'
Assume that this equation is subject to the following initial conditions
u(x,0) = f(x)
and boundary conditions
(0, t) = 0 and
ди
(1,t) + и(1,t) — 0
(i) Discuss briefly the physical meaning of the boundary conditions.
Chapter 2 Solutions
Introduction to Heat Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r1 has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - Prob. 2.9PCh. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - Prob. 2.13PCh. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Prob. 2.20PCh. 2 - Use IHT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - At a given instant of time, the temperature...Ch. 2 - Prob. 2.27PCh. 2 - Uniform internal heat generation at q.=5107W/m3 is...Ch. 2 - Prob. 2.29PCh. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.32PCh. 2 - Prob. 2.33PCh. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. 2.37PCh. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - Prob. 2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. 2.44PCh. 2 - Beginning with a differential control volume in...Ch. 2 - A steam pipe is wrapped with insulation of inner...Ch. 2 - Prob. 2.47PCh. 2 - Prob. 2.48PCh. 2 - Two-dimensional, steady-state conduction occurs in...Ch. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Prob. 2.62PCh. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Prob. 2.68PCh. 2 - The steady-state temperature distribution in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 0.6-cm diameter mild steel rod at 38C is suddenly immersed in a liquid at 93C with hc=110W/m2K. Determine the time required for the rod to warm to 88C.arrow_forwardA certain material has a thickness of 30 cm and a thermal conductivity of 0.04 W/m- °C. At a particular instant in time, the temperature distribution with x, the distance from the left face, is T = 150x ^ 2 - 30x , where x is in meters. Calculate the heat-flow rates atx x = 0 and x = 30 cm . Is the solid heating up or cooling down?arrow_forwardFind the steady-state temperature u(r,θ) in a quarter semi-circular plate of radius r=5 subject to the heat equation in polar coordinatesarrow_forward
- A plane wall of thickness 8cm and thermal conductivity k=5W/mK experiences uniform volumetric heat generation, while convection heat transfer occurs at both of its surfaces (x= -L, x= + L), each of which is exposed to a fluid of temperature T∞ = 20˚C. The origin of the x-coordinate is at the midplane of the wall. Under steady-state conditions, the temperature distribution in the wall is of the form T(˚C) = a + bx - cx^2, where x is in meters, a =86˚C, b = -500˚C/m, and c=4459. 1) Heat Flux Entering the wall is ? 2) Temperature at the left face is /arrow_forwardThe temperature distribution across a wall 0.3 m thick at a certain instant of time is T(x) = a+ b+cx?, where T is in degrees Celsius and x is in meters, a = 200°C,b = -200°, and c = conductivity of 1 W /m · K. 30°C/m² . The wall has a thermal (a) On a unit surface area basis, determine the rate of heat transfer into and out of the wall and the rate of change of energy stored by the wall. (b) If the cold surface is exposed to a fluid at 100°C, what is the convection coefficient? k=1W/m•k T(x) =200-200x + 30x² 200°C- ĖST 142.7°C q"out | Fluid Too = 100°C,h 9"in |L-0.3marrow_forwardHow long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.arrow_forward
- The temperature distribution across a wall 0.25 m thick at a certain instant of time is T(x) = a + bx + cx², where T is in degrees Celsius and x is in meters, a = 200 C, b = -200 C/m, and c = 30 C/m². The wall has a thermal conductivity of 2.5 W/m.K. (a) Determine the heat flux into and out of the wall (q"in and q'out). (b) If the cold surface is exposed to a fluid at 100 C, what is the convection coefficient h? - Degree Celsius 200°C q" In- q'in q'out= h = Choose... Choose.... Choose... L₂x K = 2.5 W/m.k T(x)-200-200 x +30x² q" Out 142.7 C 11 L=0.25 m Fluid Too = 100 °C harrow_forward0 k(T) = k₂(1+B7) Plane wall L X Example:-Consider a plane wall of thickness L whose thermal conductivity varies linearly in a specified temperature range as K(T) =k₁ (1+BT) where k, and B are constants. The wall surface at x=0 is maintained at a constant temperature 1 of T₁ while the surface at x =L is maintained at T2, as shown in Figure . Assuming steady one-dimensional heat transfer, obtain a relation for:- (a) the heat transfer rate through the wall.. (b) the temperature distribution T(x) in the wall.arrow_forwardA machine element as seen in the figure is made of pure copper. It has an inner diameter of D;=2.9 cm, outer diameter of Do=5.9 cm, and height of H=19 cm. The initial temperature of the element is 749 K, and then suddenly placed in an environment which has a temperature of Too=300O K. The temperature of the element is measured as 489 K, 4.8 minutes after the cooling process. If the lumped system method is applicable, determine the heat transfer coefficient of the environment, in W/(m²K). Note: All the surfaces should be considered to calculate the surface area. Not: Yüzey alanı hesaplamak için tüm yüzeyler dikkate alınmalıdır. Properties of pure copper: k=370 W/(mK), C=920 J/(kg°C), p=8933 kg/m³ H Dịarrow_forward
- Shown in the figure below is an insulated copper block that receives energy at a rate of 200 W from an embedded resistor. The temperature of the resistor is 34°C above the temperature of the copper block. Insulation Δt = Resistor 5000000000000000000000 oooooooooooooo....... Copper block If the block has a volume of 10-3 m³ and an initial temperature of 20°C, how long would it take, in minutes, for the temperature to reach 88°C? -V=10-³ m³ T₁ = 20°C minarrow_forwardQ1 For one -dimension heat transfer conduction consider a shielding wall for a nuclear reactor. The wall receives a gamma-ray flux such that heat is generated within the wall according to the relation 9x = 4, ( 2X+3) Where q0 is the heat generation at the inner face of the wall exposed to the ray Flux. Using this relation for heat generation, derive an expression for the temperature distribution in a wall of thickness L, where the inside and outside temperatures are maintained at Ti and TO, respectively. Also, obtain temperature in the wall at X= 0.1 m. Assume, Ti-100 °C, TO=200 °C, L= 0.2 m, K = 40 w/ m. °C, and q0 = 50 W %D gamma- %3D I 90 y FLUX То Tiarrow_forward(A) Consider a plane wall of thickness L and thermal conductivity k. The two sides of the wall are maintained at constant temperatures of T1 and T2 respectively. Show that the temperature distribution through the wall is represented as Т, - Т, T = - x + x+T| L Assume one dimensional steady state heat conductionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license