Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 2, Problem 2.43P
(a)
To determine
The differential equation for variation in temperature with angular coordinate.
(b)
To determine
The expression for temperature distribution
(c)
To determine
The expression for heat rate
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
under steady-state conditions. If you are given T1 = 200 °C and T2 = 164 °C, determine:
a) the conduction heat flux, q,.cond, in
m2
W
from x = 0 to x = L
b) if the dimensions of the triangle ares 15 mm and h 13 mm, calculate the heat
transfer due to convection, q,y, in W at x = L
Finsulation
T2
T
T = 20°C
h = 500 W/m2.K
Triangular Prism
x L
x 0
L= 50 mm
k = 100 W/m-K
Q1
Passage of an electric current through a long conducting
rod of radius r; and thermal conductivity k, results in
uniform volumetric heating at a rate of ġ. The conduct-
ing rod is wrapped in an electrically nonconducting
cladding material of outer radius r, and thermal conduc-
tivity k, and convection cooling is provided by an
adjoining fluid.
Conducting
rod, ġ, k,
11
To
Čladding, ke
For steady-state conditions, write appropriate forms of
the heat equations for the rod and cladding. Express ap-
propriate boundary conditions for the solution of these
equations.
2. A rectangular block has thickness B in the x-direction. The side at x = 0 is held at temperature
T, while the side at x = B is held at T2. The other four sides are well insulated. Heat is generated
in the block at a uniform rate per unit volume of [.
(a) Use the conduction equation to derive an expression for the steady-state temperature profile,
T(x). Assume constant thermal conductivity.
(b) Use the result of part (a) to calculate the maximum temperature in the block for the following
values of the parameters:
T₁-120 °C k-0.2 W/(m K) B-1.0 m T₂-0 F-100 W/m³
Chapter 2 Solutions
Introduction to Heat Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r1 has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - Prob. 2.9PCh. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - Prob. 2.13PCh. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Prob. 2.20PCh. 2 - Use IHT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - At a given instant of time, the temperature...Ch. 2 - Prob. 2.27PCh. 2 - Uniform internal heat generation at q.=5107W/m3 is...Ch. 2 - Prob. 2.29PCh. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.32PCh. 2 - Prob. 2.33PCh. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. 2.37PCh. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - Prob. 2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. 2.44PCh. 2 - Beginning with a differential control volume in...Ch. 2 - A steam pipe is wrapped with insulation of inner...Ch. 2 - Prob. 2.47PCh. 2 - Prob. 2.48PCh. 2 - Two-dimensional, steady-state conduction occurs in...Ch. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Prob. 2.62PCh. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Prob. 2.68PCh. 2 - The steady-state temperature distribution in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- #4: A rod of length L. coincides with the interval [0, L] on the x-axis. Let u(x, t) be the temperature. Consider the following conditions. (A) The left end is held at temperature 0°. (B) The right end is insulated. (C) There is heat transfer from the lateral surface of the rod into the surrounding medium, which is held at temperature 0° (D) The left end is insulated. (E) The initial temperature is 0° throughout. (F) The right end is held at temperature 0°. (G) There is heat transfer from the right end into the surrounding medium, which is held at a constant temperature of 0°. (H) There is heat transfer from the left end into the surrounding medium, which is held at a constant temperature of 0°. In each part below, determine which of the above conditions corresponds to the given initial or boundary condition for the heat equation. (a) u(x, 0) = 0 (b) u(0, 1) = 0 (c) du (d) ou x=L ox|x=0 = -hu(L, 1) = hu(0, 1)arrow_forwardA thermometer has a time constant of 10 s and behaves as a first-order system. It is initially at a temperature 30°C and then suddenly subjected to a surrounding temperature of 150°C. Calculate the 90 percent rise time and the time to attain 99 percent of the steady-state temperature. Repeat these calculations for a time constant of 5 s and compare the results with that of the previous casearrow_forwardFind the steady-state temperature distribution u in a semi-infinite solid cylinder (Fig. 2) of radius a if the base (at z-0) is held at 60° and the curved sides at 0'. Fig 2arrow_forward
- In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conductionarrow_forwardDerive an expression for the temperature distribution within a sphere that has inner radius r, where the temperature T, and outer radius r, where the temperature T,. Assume the heat source within the wall of sphere is q' and the heat conductivity is k. also assume one-dimensional heat transfer (r - direction)arrow_forwarda) First, let's start with the steady-state analysis for the cable. What is the steady-state temperature of the wire surface if this current has been passing through the cable for a long period of time in these underwater conditions? Enter only a numeric value (with no units entered) and express your answer in ∘C. b) Now, let's think about the transient case. Assume that the cable starts at the same uniform temperature as the water and then the electrical current is passed through the cable. We're now interested in the amount of time it takes to heat up. Start by calculating the Biot number for this scenario. Enter only a numeric value (your answer should be unitless). c)arrow_forward
- Subject: ThermodynamicsShow your solution please and givenarrow_forwardThe initial temperature distribution of a 5 cm long stick is given by the following function. The circumference of the rod in question is completely insulated, but both ends are kept at a temperature of 0 °C. Obtain the heat conduction along the rod as a function of time and position ? (x = 1.752 cm²/s for the bar in question) 100 A) T(x1) = 1 Sin ().e(-1,752 (³¹)+(sin().e (-1,752 (²) ₁ + 1 3π TC3 .....) 100 t + ··· ....... 13) T(x,t) = 200 Sin ().e(-1,752 (²t) + (sin (3). e (-1,752 (7) ²) t B) 3/3 t + …............) C) T(x.t) = 200 Sin ().e(-1,752 (²t) (sin().e(-1,752 (7) ²) t – D) T(x,t) = 200 Sin ().e(-1,752 (²)-(sin().e (-1,752 (²7) ²) t E) T(x.t)=(Sin().e(-1,752 (²t)-(sin().e(-1,752 (²) t+ t + ··· .........) t +.... t + ··· .........) …..)arrow_forwardConsider the square channel shown in the sketch operating under steady state condition. The inner surface of the channel is at a uniform temperature of 600 K and the outer surface is at a uniform temperature of 300 K. From a symmetrical elemental of the channel, a two-dimensional grid has been constructed as in the right figure below. The points are spaced by equal distance. Tout = 300 K k = 1 W/m-K T = 600 K (a) The heat transfer from inside to outside is only by conduction across the channel wall. Beginning with properly defined control volumes, derive the finite difference equations for locations 123. You can also use (n, m) to represent row and column. For example, location Dis (3, 3), location is (3,1), and location 3 is (3,5). (hint: I have already put a control volume around this locations with dashed boarder.) (b) Please use excel to construct the tables of temperatures and finite difference. Solve for the temperatures of each locations. Print out the tables in the spread…arrow_forward
- In the design of a certain computer application, a heat flow simulation is required. In the simulation, the heat conductor, which is of length 10m, has a perfectly insulated surface. The temperature at both ends of the conductor is kept consistently at zero. The initial temperature at any point of the conductor is uniform at 25°C. The 1-dimensional heat equation is given as follows: for all 0arrow_forwardSOLVE STEP BY STEO IN DIGITAL FORMAT A horizontal tube 6 m long and 123.5 cm in diameter is maintained at a temperature of 150 °C in a large room in which the air is at 20 "C and 8 W/m² "C The walls of the room are at 38 °C Assume that the emissivity of the tube is 0.76. How much heat is lost from the tube by both convection and radiation?arrow_forwardfor the following differential equation, determine (a) order, (b)degree, (c) linearity, (d) unknown function, and (e) independent variablesarrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Introduction to Diffusion in Solids; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=K_1QmKJvNjc;License: Standard youtube license