Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 2, Problem 2.17P
(a)
To determine
The thermal conductivity of the stainless steel sample material.
The average temperature of the samples.
(b)
To determine
The thermal conductivity of the stainless steel sample material.
The average temperature of the Armco iron.
(c)
To determine
The advantage in constructing the apparatus with two identical samples sandwiching the heater rather than with a single heater sample combination.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2.2: Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?
spherical shaped vessel of 14 m outer diameter is 90 mm thick Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C Thermal conductivity of the material of the sphere is 0.083 W/mK
Provide two sample question regarding Heat transfer between two fluids separated by walls of a composite tube of solid materials
Chapter 2 Solutions
Introduction to Heat Transfer
Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - Assume steady-state, one-dimensional conduction in...Ch. 2 - A hot water pipe with outside radius r1 has a...Ch. 2 - A spherical shell with inner radius r1 and outer...Ch. 2 - Assume steady-state, one-dimensional heat...Ch. 2 - A composite rod consists of two different...Ch. 2 - A solid, truncated cone serves as a support for a...Ch. 2 - To determine the effect of the temperature...Ch. 2 - Prob. 2.9PCh. 2 - A one-dimensional plane wall of thickness 2L=100mm...
Ch. 2 - Consider steady-state conditions for...Ch. 2 - Consider a plane wall 100 mm thick and of thermal...Ch. 2 - Prob. 2.13PCh. 2 - In the two-dimensional body illustrated, the...Ch. 2 - Consider the geometry of Problem 2.14 for the case...Ch. 2 - Steady-state, one-dimensional conduction occurs in...Ch. 2 - Prob. 2.17PCh. 2 - Prob. 2.18PCh. 2 - Consider a 300mm300mm window in an aircraft. For a...Ch. 2 - Prob. 2.20PCh. 2 - Use IHT to perform the following tasks. Graph the...Ch. 2 - Calculate the thermal conductivity of air,...Ch. 2 - A method for determining the thermal conductivity...Ch. 2 - Prob. 2.24PCh. 2 - Prob. 2.25PCh. 2 - At a given instant of time, the temperature...Ch. 2 - Prob. 2.27PCh. 2 - Uniform internal heat generation at q.=5107W/m3 is...Ch. 2 - Prob. 2.29PCh. 2 - The steady-state temperature distribution in a...Ch. 2 - The temperature distribution across a wall 0.3 m...Ch. 2 - Prob. 2.32PCh. 2 - Prob. 2.33PCh. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - Prob. 2.36PCh. 2 - Prob. 2.37PCh. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - The steady-state temperature distribution in a...Ch. 2 - One-dimensional, steady-state conduction with no...Ch. 2 - Prob. 2.42PCh. 2 - Prob. 2.43PCh. 2 - Prob. 2.44PCh. 2 - Beginning with a differential control volume in...Ch. 2 - A steam pipe is wrapped with insulation of inner...Ch. 2 - Prob. 2.47PCh. 2 - Prob. 2.48PCh. 2 - Two-dimensional, steady-state conduction occurs in...Ch. 2 - Prob. 2.50PCh. 2 - Prob. 2.51PCh. 2 - A chemically reacting mixture is stored in a...Ch. 2 - A thin electrical heater dissipating 4000W/m2 is...Ch. 2 - The one-dimensional system of mass M with constant...Ch. 2 - Consider a one-dimensional plane wall of thickness...Ch. 2 - A large plate of thickness 2L is at a uniform...Ch. 2 - Prob. 2.57PCh. 2 - Prob. 2.58PCh. 2 - A plane wall has constant properties, no internal...Ch. 2 - A plane wall with constant properties is initially...Ch. 2 - Consider the conditions associated with Problem...Ch. 2 - Prob. 2.62PCh. 2 - A spherical particle of radius r1 experiences...Ch. 2 - Prob. 2.64PCh. 2 - A plane wall of thickness L=0.1m experiences...Ch. 2 - Prob. 2.66PCh. 2 - A composite one-dimensional plane wall is of...Ch. 2 - Prob. 2.68PCh. 2 - The steady-state temperature distribution in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4arrow_forward3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.arrow_forward2.7 A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue. Both surfaces of this chip-aluminum system are cooled by air at , where the convective heat transfer coefficient of air flow is . If the heat dissipation per unit area from the chip is under steady-state conditions, draw the thermal circuit for the system and determine the operating temperature of the chip.arrow_forward
- 1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.075 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are hi = 18,000 W/m²-K and ho 12 W/m²-K. Determine the heat loss (kJ/min) from 5 m of pipe.arrow_forwardChoose the false statement? We can express lumped capacitance relation as the combination of Biot and Fourier numbers At very low values of Prandtl number, material has higher thermal conductivity compared to its momentum diffusivity We can calculate convective heat transfer coefficient from Nusselt number If Biot number is less than 0.1, we can neglect thermal resistance in some direction None of the givenarrow_forwardFor each of the following cases, determine an appropriate characteristic length Lc and the corresponding Biot Bi number that is associated with the transient thermal response of the solid object. Say if the global capacitance approximation is va lid. If temperature information is not provided, evaluate properties T = 300K a)oroidal shape with diameter D = 50mm and cross-sectional area AC = 5 mm², with thermal conductivity k = 2.3W / (mK) The surface of the toroid is exposed to a refrigerant corresponding to a convective coefficient eta = 50 W/( m2.k) b)A long stainless steel heated bar (AISI 304), with rectangular cross section, and dimensions w = 3mm , W = 5mm and L = 100mm . the bar issubjected to a refrigerant that provides a heat transfer coefficient of h =15 W/(m2 K) on all exposed surfaces. c)A long extruded aluminum tube (2024 Alloy) with internal dimensions and external w = 20 mm and W = 24 mm , respectively, suddenly submerged in water, with a convective coefficient of h =…arrow_forward
- H.W.5 A wall having a thickness of (4cm) has an internal heat generation of (280MW/m') and a thermal conductivity of (15 W/m.C). One side of the plate is insulated and the other side exposed to air at (30C) and heat transfer coefficient of (10W/m².C). Start from the principle to determine the maximum temperature in the plate and draw the temperature profile inside the wall.arrow_forwardThe steady-state temperature distribution in a one-dimensional wall of thermal conductivity 50 W/m -K and thickness 50 mm is observed to be T(°C) = a + bx, where a = 200 °C, b=-2000 °C/m², and x is in meters. i. ii. What is the heat generation rate in the wall? (8) Determine the heat fluxes at the two wall faces. In what manner are these heat fluxes related to the heat generation rate? (arrow_forwardGiven: Plate thickness: 30 mm k = 45 W/m°C Uniform volumetric heat generation: q = 25 MW/m³ Temperature on the right surface: 450K Temperature on the left surface: 390K Determine the following: (i) The equation for t(x). (ii) The maximum temperature and its location. (iii) The heat flow from each surface of the plate.arrow_forward
- An oven in our factory has wall of 35 cm thicknesi with inner tempereture Ot 650°C and outer tempercture 95°C, Air flows at 23°C (it is also tempereture of surrounding) 0.8 end heat convection coefficient betwren woll end air is h=20 heat conduction coefficient of the woll? )on this woll, woll's outer surfoce heat emmisivity coefficient is colculotearrow_forwardHEAT TRANSFER Calculate insulation thickness in mm (minimum value)required for a pipe carrying steam at 1800°C. The pipe sizeis 8 in and the maximum allowable temperature of outer wallof insulation is 500°C. Thermal conductivity of theinsulation material for the temperature range of the pipecan be taken as 0.04 W/m·K. The heat loss from steam permeter of pipe length has to be limited to 80 W/m. SHOW COMPLETE SOLUTION IN A PAPERarrow_forwardA body having a cylindrical shape of length equals temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 4.2 W/m^2.K. What condition should the thermal conductivity k verify in order to apply the lumped capacitance method. 1.9 m and diameter equals to 400 mm is inside a room where the ambient Select one: a. k is less than 4.2 W/m.K b. k is greater than 1.6 W/m.K O c. k is greater than 3.8 W/m.K O d. k is less than 2.1 W/m.Karrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license