Concept explainers
A 9.0 m uniform beam is hinged to a vertical wall and held horizontally by a 5.0 m cable attached to the wall 4.0 m above the hinge, as shown in Figure 10.62. The metal of this cable has a test strength of 1.00 kN, which means that it will break if the tension in it exceeds that amount. (a) Draw a free-body diagram of the beam. (b) What is the heaviest beam that the cable can support with the given configuration? (c) Find the horizontal and vertical components of the force the hinge exerts on the beam.
Figure 10.62
Problem 44.
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
College Physics (10th Edition)
Additional Science Textbook Solutions
Conceptual Physics (12th Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Conceptual Integrated Science
Sears And Zemansky's University Physics With Modern Physics
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
Essential University Physics: Volume 2 (3rd Edition)
- A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.arrow_forwardA wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.arrow_forwardA stepladder of negligible weight is constructed as shown in Figure P12.40, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P12.40 Problems 40 and 41.arrow_forward
- An individual leans forwards to pick up a box of 100 N. The weight of his upper body has a magnitude of 450 N. The back is pivoting around the base of the vertebral column. Consider the back of the individual as a rigid bar that is controlled by a muscle with an angle of 12° (See picture, d = trunk-head distance = 1 m).a) Calculate the magnitude of muscle force required to lift the box.b) Calculate the magnitude of the force at the base of the vertebral column. Hints: For (a) solve the equilibrium of moments, i.e. what force is required in the muscle to balance out the moments acting around the base of the spine.For (b), solve the equilibrium of forces acting on the spine, including the muscle force you’ve just calculated, in x and y separately. There are two extra forces not shown in the diagram: x and y contact forces acting at the base of the spine. These are whatever is needed to keep the total forces acting on the spine = 0 (so the spine isn’t accelerating off in some…arrow_forwardA 5.15-N beam of uniform density is 1.70 m long. The beam is supported at an angle of 35.0° by a cable attached to one end. There is a pin through the other end of the beam (see figure below). Use the values given in the figure to find the tension in the cable. (Assume L = 1.70 m and d = 0.390 m.)arrow_forwardA traffic light hangs from a 7.2-m long beam (AB) that is attached to a pole by a hinge (A), as shown. A horizontal (massless) cable (CD) supports the beam, making a 37° angle. The cable is attached to the pole 3.8 m above the hinge. The mass of the beam is 12 kg, and the mass of the traffic light is 22 kg. What is the tension in the cable? Also, the hinge exerts a force— with both horizontal and vertical components— on the beam. Find the magnitude of this force.arrow_forward
- A 8 000-N shark is supported by a rope attached to a 5.00-m rod that can pivot at the base. 20.0° 60.0° (a) Calculate the tension in the cable between the rod and the wall, assuming the cable is holding the system in the position shown in the figure. (Give you answer to three significant digits.) N (b) Find the horizontal force exerted on the base of the rod. magnitude direction to the right N (c) Find the vertical force exerted on the base of the rod. Ignore the weight of the rod. magnitude direction upwards Narrow_forwardA 3 meter long beam with weight 200 N is supported by a hinge at the wall and a vable as shown. A 300N block is positioned along the beam at a distance x from the wall. If the breking strength of the cable is 500 N, what is the maximum value of x? note: Please answer with most steps explained. Thank you!!! :)arrow_forwardA uniform steel bar of length 10 m is supported at point A and B using two cables as shown in the figure. The bar is hinged at point C and has a weight 500 N. What is the tension (T) force in the cable?arrow_forward
- A 420-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 150-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a 30.0 ICE CREAM SHOP (a) Find the (magnitude of the) tension T in the cable. (b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component vertical componentarrow_forwardA uniform, 8.00 m, 1150kg beam is hinged to a wall and supported by a thin cable attached to a 2.00 m from the free end of the beam as shown. Find the tension in the thin cable. Do not forget the force of gravity on the beam. b) How hard does the beam push inward on the wall? what is the horizontal force on the beam from the wall?arrow_forwardA uniform 400 N beam of length L = 4 m is supporting a 2000 N box as shown. Find the tension in the tie rope and the force F exerted by the hinge at point P. P.S. You don't have to answer the whole question. Please just explain how to solve the tension.arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning