An inexpensive food and beverage container is fabricated from 25-mm-thick polystyrene
Want to see the full answer?
Check out a sample textbook solutionChapter 1 Solutions
Fundamentals of Heat and Mass Transfer
- 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.arrow_forwardThe air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specifiedarrow_forwardA square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6arrow_forward
- An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.arrow_forwardRepeat Problem 1.35 but assume that instead of surface temperatures, the given temperatures are those of the air on the left and right sides of the wall and that the convection heat transfer coefficients on the left and right surfaces are 6 and 10W/m2K, respectively.arrow_forward1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1arrow_forward
- 1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4arrow_forward2.3 The shield of a nuclear reactor is idealized by a large 25-cm-thick flat plate having a thermal conductivity of . Radiation from the interior of the reactor penetrates the shield and there produces heat generation that decreases exponentially from a value of at the inner surface to a value of at a distance of 12.5 cm from the interior surface. If the exterior surface is kept at 38°C by forced convection, determine the temperature at the inner surface of the field. Hint: First set up the differential equation for a system in which the heat generation rate varies according to .arrow_forwardThe heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18arrow_forward
- a) A 50 mm diameter carbon steel tube (ρ = 7833 kg/m3; Cp = 465 J/kg.K, k = 54 W/mK) at an initial uniform temperature of 18°C is heated in an oven with air circulation that is at a temperature of 250°C and has a convection heat transfer coefficient of 45 W/m2.K. How long must the tube be in the oven for the surface temperature to reach 100°C? b) The figure below illustrates the temperature distribution inside a flat solid at two instants for two different situations (A and B). In both situations is there heat transfer? What causes them to behave differently?arrow_forwarda) A 50 mm diameter carbon steel tube (ρ=7833 kg/m³; Cp = 465 J/kg.K, k = 54 W/mK) at an initial uniform temperature of 18°C is heated in an oven with air circulation that is at a temperature of 250°C and has a convection heat transfer coefficient of 45 W/m².K. How long must the tube be in the oven for the surface temperature to reach 100°C? b) The figure below illustrates the temperature distribution inside a flat solid at two instants for two different situations (A and B). In both situations is there heat transfer? What causes them to behave differently?arrow_forwardQuestion 1: A glass window of width W = 1 m and height H = 2m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 °C and -20 C, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of (last two digit of your Registration number) °C and -15 °C, what is the rate of heat loss from a 1 mx2mwindow? The thermal conductivity of air is ka = 0.024 W/m.K.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning