MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.

MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the size of 14 bolts required for C.I.steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm.
As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4
The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter on the outside and 17 mm wire diameter. It measures 210 mm in free length. 82 Gpa is the modulus of rigidity. Calculate the initial compression length of the wire required to maintain a boiler pressure of 1.35 Mpa on a 30 mm diameter valve seat. (Draw the diagram)
3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
Q2/ Calculate the maximum axial stress for a 40-ft joint of 11.75-in, 60 lbm/ft, J-55 casing with short threads coupling. Where the casing is subjected to 280000 lb, axial tension load in a portion of a directional wellbore with dogleg severity of 2"/50 ft. In case of: (1)Uniform contant between the casing and the borehole wall. (2)Assuming contant between borehole wall and the casing only at the couplings,andF n+ (3)Calculate the joint setrength of the API round thread couplings.(oult = 75000 psi, wall thickness 0.489-in, Pc= 2660 psi. o yb-952000 lb, Fj-649 000 lbf).
Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.
Use LRFD and design a 13-foot-long tension member and its connection for a service dead load of 8 kips and a service live load of 24 kips. No slip of the connection is permitted. The connection will be to a 3⁄8-inch-thick gusset plate, as shown in Figure . Use a single angle for the tension member. Use Group A bolts and A572 Grade 50 steel for both the tension member and the gusset plate.
Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm2 . Take the permissible tensile stress as 35 MPa.
Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical shape, what would be it's wall thickness in mm 3. Calculate the tensile force exerted on the wall cross section area in problem (2) 4. How about the bursting force in problem (2)
The cylinder of a four stroke diesel engine has the followin, specifications : Cylinder bore :150 mm Maximum pressure : 3.5 MPa Cylinder material : GCI FG200 Factor of safety : 6 Poisson's ratio : 0.25 Determine the thickness of the cylinder wall. Also calculate the apparent and net circumferential stresses in the cylinder wall.