As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4

As shown in figure below, two plates are clamped by washer-faced 2 in-20 UNF SAE grade 5 bolts each with a standard 2 N steel plain washer. The top plate is steel and the bottom pplate is gray cast iron. If a total of 8 bolts where used to close 1 feet diameter pipe which applied at maximum pressure of 150 psi. Calculate the static and fatigue safety factor of this joint. Used Goodman theory for tha fatigue safety 1/2 factor. 3/4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ASAP
Design of a bolted assembly using a single M16x2 class 8.8 coarse-thread bolt has resulted in a joint where bolt stiffness is k, = 6 N/mm and the overall member stiffness - 18 N/mm. The fastener is to be reused (nonpermanent). Question 1 Value of joint stiffness constant: 0.25 4.0 0.5 0.1 Question 2 Magnitude of bolt tightening load (preload) Fi [kv]: 85 71 94 63
A thin-walled spherical vessel, which is made of AISI C1020, as rolled steel has a diameter of 2.5 ft. The joint efficiency of the vessel is 80%. Internal pressure of the gas inside the vessel varies continuously from 200 psi to 400 psi. If for a Factor of Safety of 1.75 based on Soderberg criterion and the surface of the vessel is polished, find the minimum safe thickness of the vessel.
19. The Knuckle Joint is made from SAE 1020 Steel having an allowable tensile strength of 15,000 psi and an allowable shear strength of 7500 psi. The axial load is 1 ton (recall, 1 ton = 2205 lb). Yoke Pin Rod -A The dimensions are as follows: D-0.652 in d-0.652 in c = 0.66 in b = 0.33 in m = 1.306 in e = 0.505 in Determine: a) Tensile stress (psi) at section A-A b) Factor of safety for a) c) Shearing stress (psi) in the pin d) Factor of safety for b) e) Bearing stress (psi) between the pin and the rod f) Factor of safety for e) g) Bearing stress (psi) between the pin and the yoke h) Factor of safety for g) i) Tensile stress (psi) across the hole in the rod j) Factor of safety for i) k) Tensile stress (psi) across the hole in the yoke 1) Factor of safety for k)
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
(do both (SR) & Euler and select the proper analysis) no metrics plz
QUESTION 1 A wolded aluminum alloy cyrindrical pressure vessel has a diameter of 8 in and a wall thickness of 3/16 in. The ultimate tensile strength of ue alloy is 65,000psi. Calculate the internal pressure that will cause rapturo O a. 2050 psi O b.2210 psi OC 3050 psa O d.3150 psi QUESTION 2 The longitudinal joint in an B-t-diamotor closed cylindrical steel boilor is butt wolded with a joint etficiency of 85 perceont. The bolor plate is 3tn thick with an allowable tensle stress of 11,000 psi. Calculate the maximum safo internal pressuro O a 154 2 psi Ob. 146.1 pi OC 1333 ps O d. 122 3 psi Click Save and Sulmit to sace andsubunit. Chick Sune All Anncers to saie all annuers
A 12 in x 14 in x 350 rpm single acting oil engine has a compression pressure of 328 psi and a maximum explosion pressure of 628 psi. The connecting rod for this engine is to be made of cold drawn, C1040 steel. What should be the factor of safety of this design? What diameter is allowed using this factor of safety?
An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load varying between +40kN and +60kN. E70XX (Sut = 482MPa, Sy = 393MPa) will be used as the welding electrode. Find the factor of safety of the weld zone. Note: that both static and dynamic loads are applied to the source.
A joint is subject to a cyclic loading. There is an acceptable preload of 1,200 lbs, and the axial load is fully reversed with an amplitude of 1,600 lb. THe tensile bolt area is 0.160 in^2. Ignore any design factors and (take all nd=1) and assume the loads include the 1.2 bolt factor. If the joint constant is 0.25, the alternate and means axial stress for the bolt are: a) sa = 1,250 psi sm = 0 b) sa = 1,250 psi sm = 8,750 psi c) sa = 2,500 psi sm = 0 d) sa = 2,500 psi sm = 7,500 psi