Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.

Q: Q3/ An engine indicator has a plunger diameter of 20mm. the indicator spring attached to this…

A:

Q: A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers.…

A:

Q: Calculate the maximum allowable pressure difference between the inside and outside of a sphere 50 mm…

A:

Q: For a specific spring where the load applied is 100 N, coil diameter is 4 mm, spring diameter is 20…

A:

Q: Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…

A:

Q: D. If the critical load for the valve push for an overhead valve engine is 380 lbs, calculate the…

A: Given data as per the question Critical load =380 lbslength =1 ft=12 inEsteel=2.9 ×107 psi

Q: Principal stresses:σ1=31.69 MPa σ2=−30.56 MPa Maximum in−plane stress: σmax=31.69 MPa

A:

Q: spherical pressure vessel designed using steel has diameter of 36inches, shell thickness of 3/16…

A: We know that in a spherical pressure vessel the longitudinal and circumferential stresses is given…

Q: An aircraft engine develops 150kW at 1500rpm. The engine output shaft is steel which fails when the…

A:

Q: bläi 10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=7000O MPa 100 kN RALU30 MM Aluminum…

A:

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: 10 95 MPa 10 cm 5 cm

A: To Find : Maximum Stress in Plate =?

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: A cast ALuminum cy linder o f Purtable hydraulic a riveter is 208 mm in diameter The Pressure 16,8…

A: The above questioni is based on cylinder analysis.

Q: A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium…

A:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: The information provided in the image includes:Maximum cylinder pressure: 3.15 N/mm²Cylinder bore:…

Q: 2) Steam of 3.5MPA is transported in a pipe of outside diameter 450mm. (Pressure 3.5MPA) The walls…

A: Given data  Steam pressure = 3.5 MPa OD of pipe (D) = 450 mm  thickness of pipe (t) = 10mm bolt dia…

Q: (15) A 150mm pulley is mounted to the motor 100mm from the bearing. The motor is 20kW & rotates @…

A: Write the given data. d=150P=20 kWN=640 rpmθ=170°

Q: min. Cylinder wall thickness for safe design

A: Given; Thin cylinder with an internal radius=100 mmor, d=2r           =100×2           =200…

Q: Required : 1. Determine the safest thickness of the vessel in mm 2. If the vessel has spherical…

A:

Q: Q1. A (50) mm diameter shaft is made of steel with a yield strength of 440 MPa. There are two…

A: Given Data The diameter of the shaft is: d=50 mm The yield strength of the shaft is: σy=440 MPa The…

Q: 0.10-in radius T 2.00-in dia. 1.25-in dia. Applied torque 2200 lb-in

A: GivenT=2200lb-inD=2ind=1.25inr=0.10in

Q: QUA four stroke internal combustion engine has the following specifications: Brake power-7.5 kW;…

A: four stroke engine Brake power (B.P.)= 7.5 KWSpeed (N)= 1000 rpmImep (Pm)= 0.35 N/mm2max. gas…

Q: A piston rod, made of AISI 3140 steel, OQT 1000 F (Fig. AF 2), is subjected to a repeated, reversed…

A: Given Data :  Piston rod material :AISI 3140 steel, OQT 1000 F piston rod diameter d = 25 in…

Q: A pressure vessel has an outside diameter of 50 mm and a wall thickness of 2mm and is subject to an…

A: Given data, Outside diameter of pressure vessel, Do = 50 mm Thickness of the pressure vessel, t = 2…

Q: The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter…

A:

Q: The wall thickness of a spherical thank is 8mm, calculate the diameter if allowable stress is 140MPa…

A:

Q: What force is required to compress a 200mm diameter hollow post with a thickness of 50mm thickness…

A: Given Data⇒ Internal diameter of hollow post(d)=200 mm Since 1 m=1000 mm Internal diameter of hollow…

Q: with a stress of 52.89  and diameter of 4cm and thickness of 2mm  (P) load of 2MPa how was the…

A:

Q: Q- Compute the tensile and compression stresses for below 40 KN 120 24 KN/m C B D 2m A NA mm 5m 3m…

A:

Q: Try One - scene 8 of 8 Pin diameter = 24 mm For the pin connection shown, determine the normal…

A: Write the formula for the normal stress acting on the gross area. σgross=PAgross Here, P is the…

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.