Problem 1 only. Solve carefully and include the Units in every step. Thanks! 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm2. A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa,A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA?3. In a 2.5 m cantilevered l-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress inbeam is 120 Mpa, determine theA. section modulus, in'.B. The base and height of the beam if the base is 75% of its height, mm.

Given: The torque transmitted by shaft, T = 850 lb.in The shaft diameter, d = 1.75 in The ultimate…

Answered: 1. A taper pin is used to fix a lever…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
Problem 1 only, solve carefully, include the units and dra the diagram. Thanks! . A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, findA. Force that will shear the pin, kNB. Shear pin diameter, mm
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
6. A hydraulic press exerts a total load of 3.5 MN. This load is carried by two steel rods, supporting the upper head of the press. If the safe stress is 85 MPa find the extension in each rod (mm) in a length of 2.5 m.
Problem 1. A shaft with a diameter d = 60 mm must transfer a torque of 350 Nm by using a key joint. The key has the following standard dimensions: b x h x 1= 18 mm X 11 mm x 50 mm. Calculate the stresses.
Determine the torsion on the rigid supports and the maximum shearing stress developed in each segment. Provide a torque diagram, strictlv follow instructed sign convention, and start from left to right. Use 2 decimal places. A 0.5 in. B 5 in. C 500 lb-ft 8 in. 1 in. D 12 in.
A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has the following standard dimensions: b x h x l = 8 mm x 7 mm x 18 mm. Calculate the stresses.
2.A lever secured to a 2 inches round shaft by a steel tapered pin (d = 3/8”) has a pull of 50 lbs at a 30 inch radius from shaft center. Find the unit working stress of the pin.
Problem 2 only, solve carefully, include the units and dra the diagram. Thanks! A 3/4 inch diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet is 80 Mpa, A. What tensile force applied each plate to shear the bolt, pounds?B. What bearing stress that the bolt can withstand, MPA
4. The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable shear stress of the material is 15000 psi. Where and how such a bolt most likely to fail, will it fail in the root diameter or the in the thread.
Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS