Design a cylindrical pressure vessel to carry compressed air for a self-contaihed breathing apparatus for use by firefighters when operating in smoke-filled buildings. The minimum inside diameter is to be 20 cm, and the length of the cylindrical portion of the tank is to be 45 cm. It must withstand a service pressure of 4.0 MPa. Use a design stress of S/8 to account for a large number of pressurization cycles. The tank is to be made from aluminum alloy 6061- T6

Design a cylindrical pressure vessel to carry compressed air for a self-contaihed breathing apparatus for use by firefighters when operating in smoke-filled buildings. The minimum inside diameter is to be 20 cm, and the length of the cylindrical portion of the tank is to be 45 cm. It must withstand a service pressure of 4.0 MPa. Use a design stress of S/8 to account for a large number of pressurization cycles. The tank is to be made from aluminum alloy 6061- T6

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Barometric pressure is 29.89 in Hg. Convert 100 kPag to psiabs
A U-tube manometer employs mercury having specific gravity of 13.5. one side of the manometer is open to the standard atmospheric pressure of 30 in-Hg and the difference in column heights is measured as 10 mm when exposed to air source at 25°C. Calculate the pressure of the air source in Pascals.
Subject: Hydraulics A closedcylindrical vessel 5 ft in diameter and 6 ft high is 3/4 filled with molasses(SG = 1.24) and rotated about its vertical axis. Air is pressurized at 14.5psi. a. If w = 50 rpm, solve for thepressure at the base at the circumference of the vessel b. If w = 75 rpm, solve for thepressure at the base at the circumference of the vessel c. Solve for w (in rpm) so that thereis no water at the base of the vessel within 1.8 ft radius
A manhole cover with a diameter of 500 mm is used for a gas storage tank. It is to be held by 26 stud bolts and the pressure inside the storage tank is to be maintained at 15 kg per sq. cm. Calculate the size of the stud bolts to be used if the load will be proportionally carried by each bolt.
Need solution through half hr please
What is the minimum duct size needed to move 200 cu ft per minute andmaintain duct velocity below 800 feet per minute?
B. Given: Cylinder Diameter = 95 mm Displacement Distance = 110 mm Pressure Ratio = 8.72 P1 = 145 Kpa T1 = 26 Degree Centigrade Mechanical Efficiency = 78% Solve: Suction Volume, Mass Flow Rate, Work Done and Shaft Power N = 1350 RPM
As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is required to support a load of 10KN if we are to neglect the weight of two pistons. (Answer must be in N) 8. 10 kN 25 mm 400 mm 75 mm0 Hinge 25 mm 0
If the compressor suction pressure is 70 pounds per square inch gaugepressure (psig) and the outside temperature is 85°F, what should thedischarge pressure be reading?
Compare the pressure in question 1A to the pressure in 4A and explain any differences. I got question 1A to the pressure P=145.3atm or 147.53kPa I got question 4A to the pressure 1.4357atm
10. A long, thin-walled cylindrical tank of length L just fits between two rigid end walls when there is no pressure in the tank. Derive the correct expression for the force exerted on the rigid walls by the tank when the pressure in the tank is p and the material of which the tank is made obeys Hooke's Law. Solve the result for p = 200 psi, r = 2 ", t = 1/8 ", v =0.3. L 2r t
A hydraulic press is used to raise an 80 kN cargo truck. If oil of specific gravity 0.82 acts on the piston under pressure of 10Mpa. What is the diameter of piston required?