Quo 2.11. Design the longitudinal and circumferential joint for aboiler whose diameteris 2.4 meter and is subjected to a pressure of1 N/mm?. The longitudiral joint is a triple riveted butt joint withan efficiency of about 85% and the circumferentialjoint is a doubleriveted lap joint with an efficiency of nbout 70 %. The pitch in theouter rows of the rivets is to be double than in the inner rows andthe width of the cover plate is unequal. The allowable stresses are:0,=7 MPa, r = 56 MPa and o̟ = 120 MPa. Asgume that the resistanceof rivets in double shear is 1.875 times that of single shear. Drawthe complete joint.

Given data,P=1 N/mm2D=2.4mηL=85%(triple riveted butt joint)ηC=70%(double riveted lap joint)σt…

Quo 2.11. Design the longitudinal and circumferential joint for a boiler whose diameteris 2.4 meter and is subjected to a pressure of 1 N/mm?. The longitudiral joint is a triple riveted butt joint with an efficiency of about 85 % and the circumferential joint is a double riveted lap joint with an efficiency of about 70 %. The pitch in the outer rows of the rivets is to be double than in the inner rows and the width of the cover plate is unequal. The allowable stresses are: 0, =7 MPa, r= 56 MPa and o, = 120 MPa. Assume that the resistance of rivets in double shear is 1.875 times that of single shear. Draw

Quo 2.11. Design the longitudinal and circumferential joint for a boiler whose diameteris 2.4 meter and is subjected to a pressure of 1 N/mm?. The longitudiral joint is a triple riveted butt joint with an efficiency of about 85 % and the circumferential joint is a double riveted lap joint with an efficiency of about 70 %. The pitch in the outer rows of the rivets is to be double than in the inner rows and the width of the cover plate is unequal. The allowable stresses are: 0, =7 MPa, r= 56 MPa and o, = 120 MPa. Assume that the resistance of rivets in double shear is 1.875 times that of single shear. Draw

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: Q2 A) For a flow rate of 300 liters/second at a velocity of 1.3 meters/second, design a seamless…

Q: A steel tubing has a 1.5-in outside diameter and a 1.210-in inside diameter. It is made of AISI 1020…

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: Calculate the maximum working pressure (in MPa) of a fire tube boiler constructed using 8-mm thick…

A: Given data:

Q: 2. A cylindrical boiler, working pressure 10 MPa, has an internal diameter of 3 m. The allowable…

A: Given data Working pressure= 10MPa Internal diameter= 3m= 3000mm Allowable stress =80MPa…

Q: With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is…

A: Given: The outside diameter of shell, Ds = 90 cm The shell thickness, t = 8 mm = 0.8 cm The…

Q: Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static…

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U- groove is…

Q: Pipes for bicycle frames are made of (A) Cold rolled steel (B) Hot rolled steel (C) Forged stee

A: Given: Pipes for bicycle frames are made of,

Q: In the figure shown, shaft A, made of AISI 1050 hot-rolled steel, is we by equal and opposite forces…

A: Givenkt=1.6L=610mmFmin=0.25kN=250NFmax=0.5kN=500N

Q: How to calculate the maximum stresses which are produced inside the boiler due to the pressure of…

A: How to calculate the maximum stresses which are produced inside the boiler due to the pressure of…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: FIND THE FORCES IN JOINT A

Q: 4. Determine the efficiency of the riveted butt joint with 20 mm main plate, 12 mm cover plates and…

A: Given data, tmp = Thickness of main plate = 20 mm = 0.02 m tcp = Thickness of cover plate = 12 mm =…

Q: A bolted joint consists of 40-mm thick AISI 1020 steel pl thick aluminum plates and compressed with…

A: GivenAISI 1020 plate thickness ts=40mmthickness of aluminium plate ta=12mmBolt MI4×2, property class…

Q: 25. A de ible strap single rive butt joint joins two (12) mm plates when the diameter of the rivet…

Q: A cylindrical tank with a semi-spherical head as shown. Tank diameter is 1.5 m, the thickness is 20…

A: Given Data: The internal pressure in the tank is Pi= 2 MPa. The diameter of the tank is D = 1.5 m.…

Q: the internal pressure is 2 MPa. Determine the maximum she stress in the cylindrical tank.

A: For solution refer below images.

Q: Why are we assuming values for h? And where does the critical force come from?

A: The h indicates the thickness of the link OB. In question, we need to determine the thickness of the…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: we have to evaluate the value of F

Q: 1, the plates are joined by a double riveted lap joint and pitcli the riveted ioint and (ii)…

Q: Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a…

Q: Solve this problem with diagram

A: Step 1:Step 2: Step 3: Step 4:

Question

Quo 2.11. Design the longitudinal and circumferential joint for a
boiler whose diameteris 2.4 meter and is subjected to a pressure of
1 N/mm?. The longitudiral joint is a triple riveted butt joint with
an efficiency of about 85% and the circumferentialjoint is a double
riveted lap joint with an efficiency of nbout 70 %. The pitch in the
outer rows of the rivets is to be double than in the inner rows and
the width of the cover plate is unequal. The allowable stresses are:
0,=7 MPa, r = 56 MPa and o̟ = 120 MPa. Asgume that the resistance
of rivets in double shear is 1.875 times that of single shear. Draw
the complete joint.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
Q2 A) For a flow rate of 300 liters/second at a velocity of 1,3 meters/second, design a seamless steel. Take factor of safety of 2.5. Longitudinal efficiency of joint, n=0.80, and internal pressure= 4 N/mm?.
(2) h Q11 what the value of P Which are safer on the rivets as shown in figure below. given that : T=100.34 MPa, ob=370.3 MPa, 19mm diameter of .rivets 12.5m 19mm 12.5m 250mm P.
A steam boiler, d meter in diameter and L m in length, is made of hard steel, generates steam at a gauge pressure of p N/mm2 . Assuming the efficiency of the riveted joints as e %. It is closed at both ends by flat cover plates which are made of Mild steel and freely supported. 1. Determine the wall thickness of the cylinder if the ultimate tensile stress = A MPa and factor of safety = B. 2. Calculate the minimum thickness necessary of the cover plates with uniformly distributed load, if the the yield point stress is C MPa and factor of safety of F. 3. Also find the increase in internal diameter, the increase in length and the increase in volume. Take E = 200 kN/mm2 and u = 0.3. d= 1.1 L= 1.54 ; p= 5.68 ; A= 328 B= 4.6 ; C= 494 ; F = 3 e= 69
Te - Effective throat thickness well in mm = 6 sin45° Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 150 mm. The plates have an ultimate strength of 275 MPa and the welding was done with F70 welding electrodes, which possesses an ultimate strength of 483 MPa. Consider a partial factor of safety of 1.7 for the welded joint and determine the design strength of the weld joint, both in tension (Tdw) and in shear (Vdw) due to the forces acting on it. a) Determine the design strength of the following weld in tension ( ) due to vertical forces. b) Determine the design strength of the weld in shear ( ) due to horizontal forces. Attached pic is shear equation for calculation Tension equation for calculation is: Tdw = FyLwte /Ymw
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.1 m, the wall thickness is 32 mm, and the internal pressure is 12 MPa. Determine the maximum shear stress in the cylindrical tank. Welded seams Lutfen birini seçin 8.75.89 MPa b. 62 50 MPa C. None d. 22.67 MPa e 103 13 MPa
H.W Find the No.of rivets wanted to joint two plates type Double cover Butt joint ,the diameter of rivet is 20cm and the shear stress 200MN/m2 and tensile force 600OMN.
Please answer, thankyou
Please solve step by step , Don't use any Ai
An angle iron made of AISI 1040 CD steel is welded to metal as shown and loaded with a dynamic load varying between +40kN and +60kN. E70XX (Sut = 482MPa, Sy = 393MPa) will be used as the welding electrode. Find the factor of safety of the weld zone. Note: that both static and dynamic loads are applied to the source.