and generates 5 KVAR. The sinusoidal voltage10.10 The load impedance in Fig. P10.10 absorbs 2.5 kwsource develops 7.5 kW.a) Find the values of inductive line reactance thatwill satisfy these constraints.b) For each value of line reactance found in (a).o od nshow that the magnetizing vars developed equalsCam the magnetizing vars absorbed.ln boogSvinstis bolleo oels 2uly 2MFigure P10.10ol20 ΩjXΩod olgns 2edad lo onizoa odi ai 1ol+.500/0°V(rms)pire power bein .coadi bns seto the pnohenSource -LineLoadssess youundersProblem

zL=RL-iXczS=20+iXTherefore z=zL+zs=20+iX+RL-iXc=(25+RL)+i(x-Xc)The current flowing through…

0.10 The load impedance in Fig. P10.10 absorbs 2.5 kw and generates 5 kVAR. The sinusoidal voltage source develops 7.5 kW. a) Find the values of inductive line reactance that will satisfy these constraints. b) For each value of line reactance found in (a), od neshow that the magnetizing vars developed equals hm the magnetizing vars absorbed.lb g bolles oels eu Figure P10.10 20 Ω jΧΩ

0.10 The load impedance in Fig. P10.10 absorbs 2.5 kw and generates 5 kVAR. The sinusoidal voltage source develops 7.5 kW. a) Find the values of inductive line reactance that will satisfy these constraints. b) For each value of line reactance found in (a), od neshow that the magnetizing vars developed equals hm the magnetizing vars absorbed.lb g bolles oels eu Figure P10.10 20 Ω jΧΩ

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

Two loads are placed in parallel across a 120Vrms 60Hz line. The first load draws 150VA at a Lagging Power Factor of 0.707, while the second load draws 50-VAR at a Leading Power Factor of 0.8. A third load is purely capacitive and is placed in parallel across the 120-V line in order to make the PF of the system equal to unity. Calculate the value of the capacitance.
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
A resistor of 4 ohmsisconnected in parallel with an impedancecoil whose resistance and inductive reactance are 3 ohms and 9 ohms, respectively. Determine the total current, in amperes, taken from a supply voltage of 120-V RMS sinusoidal source. A resistor of 3 ohmsis connected in parallel with the series combination of a resistor whose resistance is 8 ohms and a capacitorwhose capacitive reactance is 13 ohms If the capacitive branch carries a 5-A RMS sinusoidal current, calculate the total power, in watts, drawn from the supply. Three loads A, B, andC are connectedin series. Load A con sists of a resistor R. Load B con sists of an impedan ce coil with resistance of Ru andreactance of XL connected in series. Load C consists of a lossy capacitor with Rc and Xc in series. The voltages across A, B. and C are 64 volts, 40 volts, and 104 volts, respectively. The current supplied by the 192.66551-volt RMS sinusoidal source is 8 A operating at 0.996546 leadingpower factor. CalculateR, RL, XL,…
In a certain circuit supplied from 50 Hz mains, the potential difference has amaximum value of 500V and the current has a maximum value of 10A. At the instantt=0, the instantaneous values of the p.d. and the current are 400V and 4Arespectively, both increasing positively. Assuming sinusoidal variation, statetrigonometrical expressions for the instantaneous values of p.d. and the current attime t. Calculate the instantaneous values at the instant t=0.015s and find the angle ofphase difference between the p.d. and the current. Sketch the phasor diagram (neednot be to scale).
n The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of th is: Select one: O a. IVthl²/8.Rth O b. [Vth²/4.Rth O c. IVth2/2.Rth O d. Vthl²/Rth consider RMS) The Complex power absorbed by the inductive branch
If a current 5.0 A lags the applied voltage 230 V by an angle o, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled IR and L respectively. It has become the practice to say that the power factor is lagging when the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 µ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 µ F capacitor connected across applied voltage (i) the reactance of the capacitor; (ii) the current.
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
A power station is to supply four regions of loads whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station.
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
For the following numeric values, determine theaverage power, P, the reactive power, Q, and the complex power, S, of the circuit shown in Figure. Note: phasor quantities are rms.
NEED ASAP please solve this problem,Maximum Average Power Transfer. Please show full and complete solution Note: Answer from the book for Pmax is lower than 50W