Solve the following related to AC power analysis Q.5:An industrial load is supplied through a transmissionline that has a line impedance of 0.1 + j0.2 N. The60-Hz line voltage at the load is 480 /0° V rms. Theload consumes 124 kW at 0.75 pf lagging. What value ofcapacitance when placed in parallel with the load willchange the power factor to 0.9 lagging?CS

Given in the question: The line voltage is: VL=480<00V The active power consumed by the load is:…

An industrial load is supplied through a transmission line that has a line impedance of 0.1 + j0.2 2. The 60-Hz line voltage at the load is 480 /0° V rms. The load consumes 124 kW at 0.75 pf lagging. What value of capacitance when placed in parallel with the load will change the power factor to 0.9 lagging? C S

An industrial load is supplied through a transmission line that has a line impedance of 0.1 + j0.2 2. The 60-Hz line voltage at the load is 480 /0° V rms. The load consumes 124 kW at 0.75 pf lagging. What value of capacitance when placed in parallel with the load will change the power factor to 0.9 lagging? C S

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30MCQ: Under balanced operating conditions, consider the three-phase complex power delivered by the...

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
compute the RMS value for the current waveform and ys them to determine average power supplied to the resistor....
n The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of th is: Select one: O a. IVthl²/8.Rth O b. [Vth²/4.Rth O c. IVth2/2.Rth O d. Vthl²/Rth consider RMS) The Complex power absorbed by the inductive branch
A load is connected across a 25,000 Volts, 60 Hz source and draws a current of 90 A rms. If the power factor of the load is to be corrected from 0.75 lagging to 0.9 lagging, find the capacitance of the capacitor to be connected in parallel with the load.
When connected to 230 V (rms),50 Hz power line, a load absorbs 4 kW at a lagging power factor of 0.8. Find the supply current in phasor form and the value of capacitance necessary to raise the power factor to 0.95 lagging.
Two loads are connected in parallel across a 1000-V rms, 60-Hz source. One load absorbs 450 kW at 0.6 power factor lagging, and the second load absorbs 500 kW and 400 kVAR. Determine the value of the capacitor that should be added in parallel with the two loads to improve the overall power factor to 0.9 lagging.
13 ) RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a. 1.4142 V b. 5 V c. 3.535 V d. 7.07 V
A Load of 250 kW is operating at 0.95 lagging power factor.Reactive power consumed by it is ____________ a. 82.17 b. 128.07 c. 130.00 d. 129.06
A 1000-W electric motor is connected to a 120 V rms, 60-Hz source. The power factor seen by the source is 0.8, lagging. To correct the pf to 0.95 lagging, a capacitor is placed in parallel with the motor. Calculate the current drawn from the source with and without the capacitor connected. Determine the value of the capacitor required to make the correction.