Please solve all parts. Consider a sinusoidal voltage expressed as:v (t) = 170 cos(2760t – 40°) Va) Find the angular frequency w=[ Select ]rad/secb) Frequency in Hertz, f=[ Select ]Hzc) The rms value Vrms=[ Select ]d) The peak value Vpeak=[ Select ]e) If this voltage is applied to a 75 ohmresistance, compute the average powerdelivered. P= [Select ]

Answered: Image /qna-images/answer/1941d498-ed6e-4afa-8272-8d45deeb2ae2.jpg

Consider a sinusoidal voltage expressed as: v (t) = 170 cos(2760t – 40°) V a) Find the angular frequency w= [ Select ] rad/sec b) Frequency in Hertz, f= [ Select ] v Hz c) The rms value Vrms= [ Select ] d) The peak value Vpeak= [ Select ] e) If this voltage is applied to a 75 ohm resistance, compute the average power delivered. P= [Select ] >

Consider a sinusoidal voltage expressed as: v (t) = 170 cos(2760t – 40°) V a) Find the angular frequency w= [ Select ] rad/sec b) Frequency in Hertz, f= [ Select ] v Hz c) The rms value Vrms= [ Select ] d) The peak value Vpeak= [ Select ] e) If this voltage is applied to a 75 ohm resistance, compute the average power delivered. P= [Select ] >

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

2. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on at 500µs/cm and volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find (a) the frequency, (b) peak to peak voltage, (c)the amplitude and (d) the rms value
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 5ms/cm and the volt/cm switch is on 3 V/cm. a) the frequency will bel Hz b) the amplitude will be V.
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
For the waveform shown, determine: (a) Peak to Peak value (b) Peak value () RMS value (d) Frequency. If volts/div is 3V/div and Time/div is 25ms/div (No need to show the calculations)
Find thr RMS value..
The sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 50 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.6 cm and the peak to peak height is 5.8 cm. Determine the following: The frequency is = The peak to peak voltage is = The amplitude is = The R.M.S voltage is =
1) the RMS value of the current is? /2) the peak value of the voltage is?/3) the value of the reactive power is?
13 ) RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a. 1.4142 V b. 5 V c. 3.535 V d. 7.07 V
When calculating the average power delivered to a load by an AC signal, it is not as straight forward as DC. It depence on the difference in phase between the einuecidal voltage across and current through the load, and it relates to their RMS values. The average power, or sometimes referred to as the active or real power, is related to the uncierpirning sinusoidal voltage and curent by P-V Co-Walte In this question there is only a resistive load, R-6.60 and the amplitude is 98V. Determine the amplitude of the current through the load I Warkout the P- 96V resistor, 6.80 50Hz V1 R1 6.80 AMA Reset RUN / Stop ✔Electric Potential Power Charge Simulation Speed 0 Charge Flow 0 Power Brightness Current Circuit:
Given the ff. 1 kHz 5V peak-to-peak sine wave.0-3.3 V square wave with a period of 12.5μs200 Hz triangular wave with an amplitude of 4.5 V and an average voltageof 1.5 V. Solve the ff. (show formula and notes) a.) V peak to peak b.) V a (voltage) c.) RMS Voltage