Problem 12. (Problem 10.50 Page 394) The variable resistor Ro in the circuit shown in is adjusted until maximum average power delivered to Ro. a) What is the value of Ro in ohms? b) Calculate the average power delivered to Ro. c) If Ro is replaced with variable impedance Zo what is the maximum average power that can delivered to Zo? 10 -j5N 100/0° V (rms) V 3j50 Ro Copyigh 2011 Peason Education ns p ng as Pretie Ha Solution:

Problem 12. (Problem 10.50 Page 394) The variable resistor Ro in the circuit shown in is adjusted until maximum average power delivered to Ro. a) What is the value of Ro in ohms? b) Calculate the average power delivered to Ro. c) If Ro is replaced with variable impedance Zo what is the maximum average power that can delivered to Zo? 10 -j5N 100/0° V (rms) V 3j50 Ro Copyigh 2011 Peason Education ns p ng as Pretie Ha Solution:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
For the following voltage and current phasors in rms Voltage magnitude in (V) is 136 and phase angle in degree is 18 Current magnitude in (A) is 0.7 and phase angle in degree is 69 The power factor is: O 0.052 (lagging) O 0.951 (leading) O 0.777 (lagging) O 0.629 (lagging) O 0.629 (leading) O0.777 (leading)
P.3: Find the rms value for the following sinusoidal waveforms a. v= 120 sin(377t + 60°) b. i=6x 10³ sin(2# 1000r) c. u=8 x 10-6 sin(2# 5000 + 30°) P.4: Find the rms value for the following sinusoidal waveforms a. v= 20 sin 754r b. v= 7.07 sin 377r c. i=0.006 sin(400r + 20°) d. i 16 x 10³ sin(377r - 10%) P.5: Write the sinusoidal expressions for voltages and currents having the following rms values at a frequency of 60 Hz with zero phase shifts: a. 4.8 V b. 50 mA c. 2 kV
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 16 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is doubled? Select one: O 16 Vrms 32 Vrms O 8 Vrms . 8 Vrms ..... O 5.657 Vrms 5.657 Vrms ....... O 8 Vrms . 16 Vrms O 16 Vrms 8 Vrms ......
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
Find the RMS value of Vit)-100 sin(377t+76) V 141,421 V 55,10 V 100 V 70.71 V
A sinusiodal voltage having maximum amplitude of 680 V is applied to the terminals of 65 Ohm resistor. Find the rms value of current in the resistor. (Unit: A) Submit Answer
1) the RMS value of the current is? /2) the peak value of the voltage is?/3) the value of the reactive power is?
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.
Two ac generators supply the same voltage. However, the first generator has a frequency of 1.2 kHz, and the second has a frequency of 5.7 kHz. When an inductor is connected across the terminals of the first generator, the current delivered is 0.15 A. How much current is delivered when this inductor is connected across the terminals of the second generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. Number i Units 1₂ L 0000 V sin 2π f₁t Circuit 1 12 L 0000 Vo sin 2x f₂t Circuit 2