H.W.: A 440 V rms source supplies power to a load ZL = 10 + j2 Q through a transmission line having a total resistance of 1.5 Q. Find (a) the average and apparent power supplied to the load; (b) the average and apparent power lost in the transmission line; (c) the average and apparent power supplied by the source; (d) the power factor at which the source operates.

H.W.: A 440 V rms source supplies power to a load ZL = 10 + j2 Q through a transmission line having a total resistance of 1.5 Q. Find (a) the average and apparent power supplied to the load; (b) the average and apparent power lost in the transmission line; (c) the average and apparent power supplied by the source; (d) the power factor at which the source operates.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17P: Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a)...

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by (a) 1202cos(t+60) (b) 120cos(t+60) (c) 1202sin(t+60)
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
c) A heater with resistance 10 N is driven by an AC voltage source (120 V). For the circuit shown below, determine the following: 0.50 j5n Vs 120 V/50 Hz j1n Figure Ql i. The total circuit impedance, Zr, in polar form. 11. The supply current, I.. iiI. The phasor diagram indicating the supply voltage, V, and the supply current, 17 iv. Apparent Power, Real Power, Reactive Power and Power Factor. V. The heater output power. 100
Which of the following descriptions IS NOT correct for loads in power systems? A. The purely resistive load absorbs the real power from the power grid B. The purely inductive load absorbs the positive reactive power from the power grid C. The purely capacitive load absorbs the positive reactive power from the power grid. D. The average value of the instantaneous power through loads is equal to its real power. In an ac circuit, power factor correction or improvement is achieved by A. Connecting a resistor in parallel with the inductive load B. Connecting an inductor in parallel with the inductive load C. Connecting a capacitor in parallel with the inductive load A balanced delta-load can be converted to an cquivalent balanced wye- load by dividing the delta-load impedance by A. square root of 3 В.3 C. 1/3
IL 220230° Load P = 2 kW pf = 0.9 lag Assuming that the source is operating at 60 Hz, determine the following: a.) The value of the current I, in phasor form the magnitude, degrees for the angle) b.) What is the reactive power Q of the load in (volts for KVAR? c.) Is the load consuming or supplying Q? d.) What is the apparent power S of the load in KVA? e.) What is the load resistance? Express your answer in Ohms. f.) What is the load inductance? Express your answer in millihenries.
Chapter 31, Problem 065 SN An ac generator provides emf to a resistive load In a remote factory over a two-cable transmission line. At the factory a step-down transformer reduces the voltage from its (rms) transmission value Vt to a much lower value that is safe and convenient for use in the factory. The transmission line resistance is R per cable, and the power of the generator is P. The generator can supply either Vt = V1 or Vt = V2. (a) What is the ratio of the voltage decrease AV along the transmission line when operating at Vị to the voltage decrease at V2? (b) What is the ratio of the power loss Pd at V1 to the power loss at V2? Express your answers in terms of P, R, V1, and V2. (a) AV,/AV2 = 2 Edit (b) Pa1/Pa2 = %3D 2 Edit
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?